Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: travelling buttons  (Read 2201 times)

0 Members and 1 Guest are viewing this topic.

Lizzy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 654
travelling buttons
« on: March 09, 2016, 04:05:36 PM »

Hello

I know this has been discussed many times, and I have looked at past posts but the answers look complicated with different solutions for different boxes. Please could someone point me in the right direction. My friend has an Erica with the buttons disappearing into the holes, how would she go about stopping this happen.
Thank you.

Lizzy
Logged
Hoppicking in Herefordshire

Castagnari Tommy, , Giordy.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: travelling buttons
« Reply #1 on: March 09, 2016, 04:08:17 PM »

Diy, or someone to do it for you?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lizzy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 654
Re: travelling buttons
« Reply #2 on: March 09, 2016, 04:13:00 PM »

 Hello Theo

DIY..... well its her son who works with wood.

Thanks
Logged
Hoppicking in Herefordshire

Castagnari Tommy, , Giordy.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: travelling buttons
« Reply #3 on: March 09, 2016, 04:20:46 PM »

Remove the treble end
Remove the grill
Seek out the two screws that hold the keyboard on
Remove the keyboard
Shape a piece of wood to lay under the treble mechanism to restrict the button travel in the area behind where the keyboard fits
Replace keyboard
Replace grille
Refit treble end

May try to take some photos of the process tomorrow.

Lizzy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 654
Re: travelling buttons
« Reply #4 on: March 09, 2016, 04:23:53 PM »

Lester many thanks  (:)
Logged
Hoppicking in Herefordshire

Castagnari Tommy, , Giordy.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: travelling buttons
« Reply #5 on: March 09, 2016, 06:12:45 PM »

Here is a set of photos showing how to put a stop under your buttons. 
I use a soft wood like cedar or spruce.  Some people like to soften the stop with a thin layer of leather over the strip of wood.
The thickness of the wood strip needs care to get the right amount of button travel.

https://www.facebook.com/media/set/?set=a.137624888166.109685.709188166&type=1&l=9432526a79

On Facebook but set to public viewing, so you should be able to see them even if you are not a fb member
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: travelling buttons
« Reply #6 on: March 09, 2016, 06:35:04 PM »

I found some pine strips in B&Q which are already the correct thickness and depth, which was handy. Somewhere in the door/frame section I think. The last couple of boxes I limited I filed grooves into the strip for each lever as per Theo's guide (which is very useful), but I might try a thinner bit of wood and some leather next time.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: travelling buttons
« Reply #7 on: March 09, 2016, 07:22:31 PM »

I use a soft wood like cedar or spruce.  Some people like to soften the stop with a thin layer of leather over the strip of wood.

Yes - I like to use a thin (0.5 - 0.8 mm) strip of leather as described. It cushions the action just a little and makes it quieter. 

I make the grooves in the wood strip first using Theo's method, and then round them out a little using a fine rat-tail file. I then test the assembly for correct button travel first, allowing a bit extra to take up the eventual thickness of the leather. Then I glue the leather on to the strip of wood, pressing the leather gently into the rounded grooves. I use a thin spreading of contact adhesive to glue the leather - it doesn't set rock-hard (unlike PVA), so if the leather ever has to be renewed at some future stage*, it is relatively easy to remove.

* I've used this method on several instruments; the longest running has been over 8 years and the leather in the grooves is still good and not worn through.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lizzy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 654
Re: travelling buttons
« Reply #8 on: March 09, 2016, 07:55:05 PM »

Many many thanks I have passed on the information will update in the future.
Lizzy
Logged
Hoppicking in Herefordshire

Castagnari Tommy, , Giordy.

laurenth

  • Member
  • *
  • Offline Offline
  • Posts: 40
Re: travelling buttons
« Reply #9 on: March 14, 2016, 01:44:30 PM »

Hi,

on his tips & tricks section, Bernard Loffet describes a similar job for the Pokerwork/2915, using a piece of floor carpet.
Logged
Laurent :||:

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: travelling buttons
« Reply #10 on: March 14, 2016, 02:23:33 PM »

Just don't push them all the way down in to the holes!!!
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Lizzy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 654
Re: travelling buttons
« Reply #11 on: March 16, 2016, 03:53:55 PM »

Many thanks to all. The box has now been adjusted so the buttons do not travel as far into the hole.

Many thanks to Sammypenn of this Parish who did the work for my friend he has done a splendid job. This box now plays like a dream.
Logged
Hoppicking in Herefordshire

Castagnari Tommy, , Giordy.

Johnniez

  • Good talker
  • **
  • Offline Offline
  • Posts: 51
Re: travelling buttons
« Reply #12 on: May 15, 2016, 01:06:15 PM »

Here is a set of photos showing how to put a stop under your buttons. 
I use a soft wood like cedar or spruce.  Some people like to soften the stop with a thin layer of leather over the strip of wood.
The thickness of the wood strip needs care to get the right amount of button travel.

https://www.facebook.com/media/set/?set=a.137624888166.109685.709188166&type=1&l=9432526a79

On Facebook but set to public viewing, so you should be able to see them even if you are not a fb member

Hi Theo

What would be optimum as far as the depth that the button stops?
On my114 they all bottom out and I think contributes to spring breakage.

Are your buttons in your pics set at that point which I see as pretty much flush with the keyboard when depressed? Is that the point roughly??

Tnx for pics great help

If you or anyone else have done this to a 114 could I get the dimensions width, height and thickness if possible ..Cedar is the wood for the project . right ?

========================

Also like to thank whoever posted about the crochet hook info for spring removal and replacement..Sure made life a lot easier doing the job. A LOT easier..

Johnnie
« Last Edit: May 15, 2016, 01:17:59 PM by Johnniez »
Logged
Every Day Is A Great Day
Some Are Better Than Others

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: travelling buttons
« Reply #13 on: May 15, 2016, 01:52:48 PM »

The limit on button travel is a matter of personal preference.  I like them to stop when they feel as if they are flush with the top of the keyboard.  When I've measured they are actually slightly below. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Grape Ape

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1209
Re: travelling buttons
« Reply #14 on: May 30, 2016, 07:19:15 PM »

Just did this to my Hohner Presswood yesterday.  The hardest part was getting the piece of wood just the right size.  As it is, the top few buttons have a bit more play than the rest, but the effect is still quite dramatic.  Previously the buttons sank way down into the holes and took my fingers with them.  The action was mushy and slow.  Now the action is more comparable to a high end box.  Last night I couldn't stop playing it.  What a difference!
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal