Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: First tuning attempt  (Read 2079 times)

0 Members and 1 Guest are viewing this topic.

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
First tuning attempt
« on: March 30, 2016, 12:31:06 AM »

Well I've had a go at tuning my first box, and it didn't turn out too badly, I think :Ph
Here's a quick demo of how it turned out: https://www.youtube.com/watch?v=nw2FMznPNe0

It's a little A/D black celluloid thingy my partner picked up on German eBay. It was in a bit of a state (nails!), but I've largely finished restoring it now, bar the bellows tape and squeaky bass levers. It has a surprising amount of dynamic range and a very sweet sound. I tuned it right down to somewhere in the swing range from the original +33 cents wetness (think it ranges from +2 at the low end to +8 at the high end at the moment), and replaced/adjusted a broken reed. Probably needs adjusting a bit more this week as some of the reeds have shifted a bit since I tuned them.

I have a few questions before I have a bash at my next project:
  • I had a bit of trouble getting the chords sounding right, I ended up flattening the thirds a bit as I read somewhere that that's not uncommon. Is there any guideline to how much to flatten them, or is it more of a trial and error job?
  • Is there a correct technique for raising/lowering the reed height? I found a guide for harmonica reed adjustment which said to press at the bass of the reed and lift the tip up, and I seem to have got them all responding roughly the same, but I couldn't find much other info on how to do it.
  • When tuning a reed down by a large amount, is it correct to use a scratcher to do this, or would it be better/neater to file it?
  • When scratching a reed I tried not to make any specific scratch too deep in case it weakened the structure, so it results in quite a few separate ones for the larger adjustments. Is that a reasonable approach?
« Last Edit: March 30, 2016, 12:43:28 AM by robotmay »
Logged

forrest

  • Other Places::
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1009
  • digits still functioning
Re: First tuning attempt
« Reply #1 on: March 30, 2016, 07:15:50 AM »

Well I've had a go at tuning my first box, and it didn't turn out too badly, I think :Ph
Here's a quick demo of how it turned out: https://www.youtube.com/watch?v=nw2FMznPNe0
I have a few questions before I have a bash at my next project:
  • I had a bit of trouble getting the chords sounding right, I ended up flattening the thirds a bit as I read somewhere that that's not uncommon. Is there any guideline to how much to flatten them, or is it more of a trial and error job?

  The sound of your box is quite pleasant. If you intend to keep the thirds on the chord side, flattening them will make the 1-3 interval sweeter. You can flatten up to 13.5 cents, where the third is at it's best, but..... this could cause problems playing with others, especially instruments tuned in equal temperament. Personally, my boxes have thirds tuned in the range of 5 to 8 cents, except for my Welty 4 stopper, which is at 10 cents flat (it was factory tuned to be 18 cents flat, I don't know why). See the thread here if you haven't already. And when you decide how much you wish to flatten your thirds, (it's all up the the ear of the beholder) then make sure that your chord thirds match your treble row thirds, or there will be some discord.
« Last Edit: March 31, 2016, 06:22:01 AM by forrest »
Logged

Rog

  • Hero Member
  • *****
  • Online Online
  • Posts: 2525
  • Repair and tuning in Hants
Re: First tuning attempt
« Reply #2 on: March 30, 2016, 07:32:14 AM »

Sounds nice. What do the higher notes sound like?

robotmay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 820
Re: First tuning attempt
« Reply #3 on: March 30, 2016, 09:09:28 AM »

    Well I've had a go at tuning my first box, and it didn't turn out too badly, I think :Ph
    Here's a quick demo of how it turned out: https://www.youtube.com/watch?v=nw2FMznPNe0
    I have a few questions before I have a bash at my next project:
    • I had a bit of trouble getting the chords sounding right, I ended up flattening the thirds a bit as I read somewhere that that's not uncommon. Is there any guideline to how much to flatten them, or is it more of a trial and error job?

      The sound of your box is quite pleasant. If you intend to keep the thirds on the chord side, flattening them will make the 1-3 interval sweeter. You can flatten up to 13.5 cents, where the third is at it's best, but..... this could cause problems playing with others, especially instruments tuned in equal temperament. Personally, my boxes have thirds tuned in the range of 5 to 8 cents, except for my Welty 4 stopper, which is at 10 cents flat (it was factory tuned to be 18 cents flat, I don't know why). See the thread here if you haven't already. And when you decide how much you wish to flatten your thirds, (it's all up the the ear of the beholder) then make sure that your chord thirds match your treble row thirds, or there will be some discord.[/list]

    I think the ones I flattened are just below 0, so probably around -2. It sounded rather odd with them at 0 for some reason, perhaps they were going sharper under increased bellows pressure? Thanks for the tips! ;D

    Sounds nice. What do the higher notes sound like?

    Not quite as squeaky as a 2 voice D/G, at least (though still pretty up there)! I'll do another little clip later on when I'm more awake/not in pyjamas :o
    Logged

    Steve_freereeder

    • Content Manager
    • Hero Member
    • ***
    • Offline Offline
    • Posts: 7511
    • MAD is inevitable. Keep Calm and Carry On
      • Lizzie Dripping
    Re: First tuning attempt
    « Reply #4 on: March 30, 2016, 09:54:16 AM »

    Well I've had a go at tuning my first box, and it didn't turn out too badly, I think :Ph
    Here's a quick demo of how it turned out: https://www.youtube.com/watch?v=nw2FMznPNe0

    I think you have made a really nice job of the tuning there, well done! I would be happy to play that box so far. However, as Roger commented, I'd like to hear the higher notes too.

    Quote
    I had a bit of trouble getting the chords sounding right, I ended up flattening the thirds a bit as I read somewhere that that's not uncommon. Is there any guideline to how much to flatten them, or is it more of a trial and error job?
    It depends on what you find suits your ear best and also whether you can detect any clash between LH flattened thirds and the RH equivalent notes (which normally won't be flattened). This in turn depends on the degree of RH tremolo - generally the greater the tremolo, the more it can mask any clashes.

    Ideally to make the sweetest major chords, the thirds need to be tuned about 14 cents flat of ET, but that's normally far too much to be acceptable except for Cajun one-rows (where the RH is usually tuned similarly). Based on my own experience, and having learned a lot form Theo and Rees, for a two row box I generally tune my LH thirds no more than 5 cents flat. Any more than that and it begins to clash with the RH side to my ears.

    Also note that for minor chords, this doesn't apply. Tempering the thirds for minor chords is less well-defined, but generally around 7 cents sharp of ET makes a lovely sound. However, that may be too much to avoid the RH clash, so I compromise by either leaving the thirds at 0 cents offset or else making them slightly sharp - say by 3 or 4 cents.

    Quote
    Is there a correct technique for raising/lowering the reed height? I found a guide for harmonica reed adjustment which said to press at the bass of the reed and lift the tip up, and I seem to have got them all responding roughly the same, but I couldn't find much other info on how to do it.
    I've learned form Theo: With the reed block directly on the tuning bellows, I gently test the pull and the push alternatively to see if there is the slightest delay or breathiness in the reeds speaking. I use the combination of a cocktail stick and a dentist's hand scaling tool (made of softish steel and has hooked end a bit like a '?') to adjust the height of the reeds up or down as required. I assume you are aware of what adjustments are needed - if not, ask here again. As setting the reed tip height can have a small effect on the reed pitch, I do all the setting/response optimisation before the final tuning.

    Quote
    When tuning a reed down by a large amount, is it correct to use a scratcher to do this, or would it be better/neater to file it
    I prefer to use a file to make large pitch adjustments or else a large-size scratcher for bass reeds sold by Charlie Marshall:
    http://www.cgmmusical.co.uk/CGM_Musical_Services/Reed_Tuning_Tools.html#0

    Quote
    When scratching a reed I tried not to make any specific scratch too deep in case it weakened the structure, so it results in quite a few separate ones for the larger adjustments. Is that a reasonable approach?
    On the larger and medium-sized reeds you can go fairly deep with the scratcher, but a few separate scratches is also acceptable. On the small, high reeds go carefully and not too deep!

    Overall, it sounds as if you are doing all the right things and asking the right questions of both us and yourself, which is good. There is ultimately only one way to learn and that is to do it for yourself and gain the experience. I have a little mantra which I try to repeat in my head whenever I'm tuning: "respect the reeds, respect the reed maker, respect the steel". I find it helps me concentrate on the job and be careful.
    Logged
    Steve
    Sheffield, UK.
    www.lizziedripping.org.uk

    robotmay

    • Hero Member
    • *****
    • Offline Offline
    • Posts: 820
    Re: First tuning attempt
    « Reply #5 on: March 30, 2016, 11:17:33 AM »

    Thanks Steve! Here's a quick demo of the higher end, with some possibly dodgy audio sync, but it's too early in the day for me to faff around with that:

    https://www.youtube.com/watch?v=tNvneJ6r0iE

    I wasn't sure if there was a correct way of raising/lowering the reeds to adjust the gap. I just ended up poking them one way or the other until they stopped stalling and started as easily as possible ;D
    Thanks for the link to the large scratcher. My current one is only 1mm, so that looks like it'd be useful.

    I've got a rather nice condition Hohner Student II PA that I'll take a stab at next I think, before I get started on my Bb/Eb Erika that I'm really excited about (and therefore don't want to cock up).
    Logged

    playandteach

    • Hero Member
    • *****
    • Offline Offline
    • Posts: 3526
    • Currently a music teacher in a high school.
    Re: First tuning attempt
    « Reply #6 on: March 30, 2016, 01:00:50 PM »

    I agree - very quickly found myself not listening to tuning, but to the playing and sound of box (and the tune - I must find the dots) which must be a good thing.
    Logged
    Serafini R2D2 GC, Serafini GC accs 18 bass

    robotmay

    • Hero Member
    • *****
    • Offline Offline
    • Posts: 820
    Re: First tuning attempt
    « Reply #7 on: March 30, 2016, 01:39:36 PM »

    The dots for that one are in the second Naragonia tunebook (:)
    Logged
    Pages: [1]   Go Up
     


    Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
    SimplePortal 2.3.5 © 2008-2012, SimplePortal