Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: The new system  (Read 4737 times)

0 Members and 1 Guest are viewing this topic.

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
The new system
« on: April 15, 2016, 10:10:33 AM »

Hey people!!!
The new system, treble key lever ,bearing...
What do you think ?? Perhaps a good,, ??? Perhaps the bearing build-up of dirt,,??

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: The new system
« Reply #1 on: April 15, 2016, 10:57:51 AM »

Yes that looks very strong and stiff.   Should make an action with a very positive feel.    Is it available from Carini, or somewhere else?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: The new system
« Reply #2 on: April 15, 2016, 11:12:16 AM »

That's the system available from Slovenia - I bought a set  a few years ago.

I found that the supplied rod was a little loose in the brass ferrules, and I ended up drilling/reaming out to a slightly larger diameter.

It took some tweaking to drill the holes for the springs, but once the springs were there, the system worked pretty well.

I ended up using the 'Carini'-system instead, where the fulcrum-rod fits in the brass clip, rather than through the solid brass nut. It found that the fit around the pivot point was too hard to get 'right', and despite being a good solid construction, I ended up with a slightly wobbly feel. Perhaps you need better tools and/or skills than me to ream out the centre holes, and if you can get that 100% wobble-free, it's a pretty good mechanism.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: The new system
« Reply #3 on: April 15, 2016, 11:17:33 AM »

It took some tweaking to drill the holes for the springs, but once the springs were there, the system worked pretty well.


I think I can see holes for springs already in these levers.

What kind of reamer did you use Lars?
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: The new system
« Reply #4 on: April 15, 2016, 01:40:46 PM »

http://vsezaharmoniko.com/mehanika-za-harmoniko/diskant-mehanika


I have a 3 mm reamer,, and 3 mm silver steel stick,,
There will be a very good  (:)
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: The new system
« Reply #5 on: April 15, 2016, 01:47:27 PM »

looks a bit heavy? Would holes save weight without loss of strength?
Logged
  _       _    _      _ 

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: The new system
« Reply #6 on: April 15, 2016, 02:42:44 PM »

I made a reamer out of the same hardened steel I used as fulcrum rod. Tapered with a file, and roughed the surface with 1200 grit sandpaper. Took forever, but good results. By using the same rod as base for a reamer, I was sure that the final size of the hole would be perfect.

Not all levers has holes for the spring. Out of a set of just under 40 levers I bought, only 3 had holes for the springs.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: The new system
« Reply #7 on: April 15, 2016, 03:10:36 PM »

Surely, if you managed to taper it with a file, you could also have filed in a spiral cutting edge? It would have made the reaming much quicker and easier.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: The new system
« Reply #8 on: April 16, 2016, 12:39:24 AM »

Straight cutting edges can work very well, especially in brass, if you go for multiple cutting edges make sure to use an uneven number (5 is traditional for clock / watchwork which tends to mean holes in brass) helically# edged reamers are a comparatively modern tool !

Silver steel* can be filed to shape, water hardened and then oilstoned to attain the cutting edge, easy sharpness test method, try to gently push the cutting edge along a finger or thumbnail, if it digs in then its sharp, if it slides, go back to the oilstone for a while.

A favourite simple reamer for model engineers is made by filing an oblique flat surface of about 30 degrees on the endpart of a bit of silver steel, the face ends up as an elongated oval** - normally for lathe use but if these arms are clamped and the bit run through them from a drill in a stand ought to work, I have never tried one hand held and suspect in a short bush the hole might wander.

Hope the project works out well

#Helix, think screw thread, Spiral, think record groove  ;)
* Known as Drill rod in the US of A - High carbon, water quenchable steel, ground to a very close tolerance for making drills reamers punches, chisels and other accurately sized or easily hardened items from.
**A 1/4" reamer of this pattern worn too short for further use is the weapon of choice for cleaning grot from finger nails hereabouts  (:)
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: The new system
« Reply #9 on: April 16, 2016, 02:25:46 PM »

Surely, if you managed to taper it with a file, you could also have filed in a spiral cutting edge? It would have made the reaming much quicker and easier.

Sure, but I found that the tapered end with nothing more than a roughed (with grit 1200) surface gave a nice and very clean inner surface. I only had to take it out from 2.8 mm to 3.0 mm.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: The new system
« Reply #10 on: April 16, 2016, 04:01:09 PM »

Mind you, I was only working with rubbishy old wood, as well. I've still got to figure out a way to get the axle out of a no-name 2-row when I get back.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: The new system
« Reply #11 on: April 16, 2016, 04:08:29 PM »

Applying heat to the end of the rod often softens the old grub and dirt enough to get it out. And patience, determination, and a few coffee breaks when it's not working:)
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: The new system
« Reply #12 on: April 16, 2016, 04:12:11 PM »

For the usual 3mm (actually 2.98 or 2.99 mm!) rod as can be obtained from Carini a 3.00 reamer will guarantee a wobbly lever. You must  start with a 2.97 reamer and then work your way up with (home made) reaming rods and fine oiled steel wool more or less as described by Lars. Reaming is tricky business and requires quite some practice and patience. Among other things it is vital to continuously remove any brass residue that will inevitably appear on the steel rods during the process.
« Last Edit: April 16, 2016, 04:29:01 PM by diatonix »
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: The new system
« Reply #13 on: April 16, 2016, 05:18:19 PM »

The shaft silver steel 2.98 m
reamer 3.0mm
loose 1 mm  ..    away from the shaft 130 mm
Is it too much
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: The new system
« Reply #14 on: April 17, 2016, 10:12:02 AM »

Any lateral movement is too much. You must start with a 2.97 reamer.
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: The new system
« Reply #15 on: April 17, 2016, 10:55:12 AM »

OK. thank you for doing this to me difficult... :'(
maybe fine Trizact Compound ???
Logged

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: The new system
« Reply #17 on: April 17, 2016, 11:32:07 AM »

I'd be very unhappy about having to clart-on with reaming brand new gear! Surely they should be a good enough fit from the factory? I'd certainly be asking the manufacturers why they weren't, if they aren't.

Reaming the individual pivots could prove to be very awkward without constructing some sort of jig to keep them perfectly aligned. Considering the length of the arms, it wouldn't take very much of a misalignment at the pivot to render them almost useless by the time they reach the button or the pallet.

Google Translate to Finnish:

Olisin hyvin tyytymättömiä ottaa hyytymään kanssa väljentäminen uusi vaihde! Varmasti ne pitäisi olla tarpeeksi hyvä istuvuus tehtaalta? Olisin varmasti kysyä valmistajilta, miksi ne eivät olleet, jos ne eivät ole.
Väljentäminen yksittäiset kääntyy voi osoittautua erittäin hankala ilman rakentaa jonkinlaista jigi pitää ne täysin suorassa. Ottaen huomioon varsien pituus, se ei ota kovin paljon on vinoutuminen on pivot niiden tekemiseksi lähes hyödytön, kun he saavuttavat painiketta tai lavan.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

dino.pafftti

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 464
Re: The new system
« Reply #18 on: April 17, 2016, 12:02:07 PM »

this is difficult, I have Italian bearing hole 3.0 mm shaft 2.98,5 Slovakian bearing, bore 29.8mm,, axis of 2.97 mm..
I think that this axis that I have silver steel, 2.98 m in diameter the same hole Slovakian bearing  :M :D
very small grinding,,
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: The new system
« Reply #19 on: April 17, 2016, 09:32:10 PM »

A close-up of my 2.97mm reamer. I bought this and others quite some years ago in one of Castelfidardo's hardware shops and even after having been used on  close to 8000 levers it's still as good as new. It must be used as a hand tool, so don't put it on an electric drill.
Carini too can supply these (reamer =alesatore), price used to be around EUR 100 per piece, probably even more expensive today. There is also a Swiss manufacturer (Wyss).
« Last Edit: April 17, 2016, 09:36:03 PM by diatonix »
Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal