Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Hohner reed lifting tool  (Read 7153 times)

0 Members and 1 Guest are viewing this topic.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner reed lifting tool
« Reply #20 on: May 09, 2016, 08:23:16 AM »

Another source for music wire is guitar or electric bass (the core, for larger diameters) strings.

Have you actually tried these? They may be steel strings, but my gut feeling is that they would not be stiff enough for reed lifters. I may be wrong of course!
The saxophone springs I mentioned in my earlier post are blued spring-tempered steel.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner reed lifting tool
« Reply #21 on: May 09, 2016, 12:47:01 PM »

I get piano wire from a harpsichord maker. I've made several different sizes. Important, also, that the hook twists slightly in the direction you push the reed. As Theo says, essential (and brilliant) for tuning without having to remove the reed blocks (and much quicker too).

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner reed lifting tool
« Reply #22 on: May 09, 2016, 12:49:10 PM »

Important, also, that the hook twists slightly in the direction you push the reed.

??? Lost me there?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner reed lifting tool
« Reply #23 on: May 09, 2016, 12:58:58 PM »

Yes, sorry, a bit cryptic. I was referring to the shape of the hook. So if it is U shaped, the hook arm also twists a few degrees off the verical. If if I can get a close up picture I'll post one.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner reed lifting tool
« Reply #24 on: May 09, 2016, 01:58:28 PM »

So the leg that lifts the reed is slightly trailing  - or leading - wrt the main leg?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Hohner reed lifting tool
« Reply #25 on: May 09, 2016, 02:13:04 PM »

Quote
Have you actually tried these? They may be steel strings, but my gut feeling is that they would not be stiff enough for reed lifters. I may be wrong of course!
The saxophone springs I mentioned in my earlier post are blued spring-tempered steel.

Yes I have actually used old strings to make new springs or reed lifters.  Works for me.  As far as I know it's the same piano wire Theo and Roger mention.  See https://en.wikipedia.org/wiki/Piano_wire

And here is a picture with a twist.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner reed lifting tool
« Reply #26 on: May 09, 2016, 06:48:47 PM »

Quote
Have you actually tried these? They may be steel strings, but my gut feeling is that they would not be stiff enough for reed lifters. I may be wrong of course!
The saxophone springs I mentioned in my earlier post are blued spring-tempered steel.

Yes I have actually used old strings to make new springs or reed lifters.  Works for me.  As far as I know it's the same piano wire Theo and Roger mention.  See https://en.wikipedia.org/wiki/Piano_wire

And here is a picture with a twist.
OK - thanks for the extra insight!  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner reed lifting tool
« Reply #27 on: May 14, 2016, 10:22:15 AM »

The hook is very easy to make from a scrap of piano wire of about 0.7mm
Took about ten minutes to make one (including handle), and having the right size does make a great deal easier to use.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Hohner reed lifting tool
« Reply #28 on: May 14, 2016, 01:25:17 PM »

On the subect of handles for homemade lifters, I use a pin vice to turn cobolt drill bits into scratchers and the same pin vice would hold a wire lifter. Double ended pin vices are available and I use one with two diameters of scratcher but it could have a scratcher at one end and a lifter at the other. I use a stiffish feeler gauge for supporting the reed when scratching or filing with a pen sander.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner reed lifting tool
« Reply #29 on: May 21, 2017, 04:00:32 PM »

Having made a German type lifting tool from an 0.3mm feeler gauge, and got the hang of using it, I find I've bent the tips of a couple of reeds with it.

Since others seem to use to same thickness, is there a particular technique?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner reed lifting tool
« Reply #30 on: May 21, 2017, 04:21:40 PM »

is there a particular technique?

Yes, but I could not explain in words.

But...

.3mm of rather hard steel may be too thick for some reeds. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner reed lifting tool
« Reply #31 on: May 21, 2017, 04:32:08 PM »

Yes, I think you're right. They were the top reeds.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Hohner reed lifting tool
« Reply #32 on: May 21, 2017, 08:00:10 PM »

For medium and large reeds I made a dual ended magnetic lifter by epoxying two 10mm x 5mm x 1.5mm rare-earth magnets in slots cut in brass tubing. Works fast with no chance of 'trauma' to reeds or valves.

Scott

BellingersButtonBoxes.com
Logged
too many boxes...please buy one, or two, or

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner reed lifting tool
« Reply #33 on: May 21, 2017, 08:31:19 PM »

Very neat.  (:)
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Hohner reed lifting tool
« Reply #34 on: May 22, 2017, 12:12:43 AM »

A very useful tool, Scott.

Some while ago, after a desktop hard drive failure, I dismantled said HD and salvaged the magnet, which I now use as a reed lifter. I can see the advantage of Scott's design in that the magnet is smaller, so will work well with the valve attached, whereas I have to remove and then re-attach  the valve, often more than once (!), though from experience I can usually compensate for the flattening effect of the valve fairly accurately while tuning.

However, it doesn't work too well on the very highest reeds, especially those with thicker reedplates, because it is attempting to pull them beyond the limit to which the reed will happily bend.

IMHO, with the highest pull reeds, if they need to be sharpened, there is no substitute for removing them from the block and tuning them a little higher than required, wax them back in and then *carefully* using a scratcher to flatten the pitch to where it is required.
Logged
Tuner/repairer, now retired.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Hohner reed lifting tool
« Reply #35 on: May 22, 2017, 08:49:01 AM »

These guys were giving me the most grief.  I could lift them with a hook but they always escaped before I could hold them in position. 
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner reed lifting tool
« Reply #36 on: May 22, 2017, 09:21:36 AM »

....IMHO, with the highest pull reeds, if they need to be sharpened, there is no substitute for removing them from the block and tuning them a little higher than required, wax them back in and then *carefully* using a scratcher to flatten the pitch to where it is required.

This is a good method and I have used it successfully. However, it is still a pest having to remove the reeds from the block to do this, and rewax them afterwards. Easier, of course if the reed plates are nailed or screwed rather than waxed.

These guys were giving me the most grief.  I could lift them with a hook but they always escaped before I could hold them in position. 

I've stopped trying to use a reed lifter for the tiny high-pitched reeds; too much risk of over-bending and damaging the reed tongue.

Other than Malcolm Clapp's method described above, I seem to have settled on two alternatives to sharpen the highest pull reeds:

1. I support the tip of the reed tongue using a flat bar of brass (just happened to have it lying around from a separate project) about 5 mm wide and 3 mm thick, which is poked through the reed block opening and held flat against the reed tongue to support it. I can then very carefully use a fine tipped, sharp scratcher to stroke the reed tongue close to the tip. This gently removes tiny amounts of steel and hence raise the pitch, testing the pitch frequently as I work. It's quite slow going, but then again one shouldn't be hurrying work on these delicate reeds.

2. Alternatively, I use a thin and very fine (400 grade) diamond round needle file poked through the reed plate slot to extremely carefully remove steel directly from the area of the reed tip, testing the pitch frequently. This method relies on feeling and working with the natural springiness of the reed tongue, which remains unsupported. Again, the file action should be thought of as no more than a gentle stroking. The reed tongue does not need to be, should not be, pushed beyond a millimetre or so out of its rest position. I also take great care not to contact the sides of the reed plate slot with the file.

Both methods need very gentle and sensitive work in order not to damage the reed tongue or the reed plate slot. Care and patience!


Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Prestidigitator

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 448
  • Saltarelle, Hohner, Oakwood Baffetti
Re: Hohner reed lifting tool
« Reply #37 on: May 22, 2017, 10:11:36 AM »

For medium and large reeds I made a dual ended magnetic lifter by epoxying two 10mm x 5mm x 1.5mm rare-earth magnets in slots cut in brass tubing. Works fast with no chance of 'trauma' to reeds or valves.

Scott

BellingersButtonBoxes.com

Same here, but a bit cruder. I find these very useful for all sizes of reeds, and I made some right-angle brass and bronze "lifters" of various sizes to support the reeds lifted by magnet, when working in confined spaces. The black marks on mine are so that I recognise them when delving in the tool boxes.
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Hohner reed lifting tool
« Reply #38 on: May 27, 2017, 05:02:22 PM »

Since I never saw anyone else tune reeds before I got into this 20+ years ago I designed my own tools, they don't look anything like yours, I'll post pics.
The magnet suggested by another poster is a great tool, it works great for pulling up outside reeds that have no gap so you can't get a shim under them.
 I just remove really high reeds if I need to raise the pitch of the inside reed. It's just too easy to damage them.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal