Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: How to remove treble action  (Read 3524 times)

0 Members and 1 Guest are viewing this topic.

Frank Bruce

  • Member
  • *
  • Offline Offline
  • Posts: 13
How to remove treble action
« on: May 12, 2016, 12:53:03 AM »

I'm not sure how to remove the treble action from this recent buy. It is not branded anywhere.

Each lever/key has its own compartment. There is the end of a rod at the side which may possibly run the width of the action and act as a pivot, but seems a bit seized or I would have to pry of the top. I'm reluctant to do either without advice in case I do some damage.

Also, what metal would be a good choice to cut new latches from and to make the metal corner strengthener?

Any suggestions would be much appreciated.
« Last Edit: May 12, 2016, 09:27:00 AM by Frank Bruce »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to remove treble action
« Reply #1 on: May 12, 2016, 10:20:51 AM »

The rod you can see sticking out at one end is indeed the axle that all the keys work on.  They can be very difficult to remove, and if brass can break off very easily.  There is no simple easy answer, but things you can try are -

rotating the rod carefully, this may be enough to free it and then pulling while continuing to rotate it may get it moving.  Getting a good grip on the rod without causing damage is difficult too.   I've found the best tool for this is the chuck from a drill.  Second best is a vice.  Pliers are more likely to do damage than to extract the rod.

I have seen suggestions of passing a low voltage electric current through the rod to warm it up which can loosen it, but I've never had any success with this method and there are dangers of causing damage if things get too hot. 

It's a difficult one. If al the keys move freely I would leave the axle rod where it is.

Hard brass would be the metal for the latches.  The originals are probably nickel plated brass. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

deltasalmon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1002
Re: How to remove treble action
« Reply #2 on: May 12, 2016, 10:48:24 AM »

To remove the rod from my one row I used one of these. I put the small end at the end of the rod and very lightly tapped the other end with a hammer or mallet. I've only tried this method on one accordion (the only one I've ever tried to remove the rod) but it worked great for me.
Logged
Sean McGinnis
Bordentown City, NJ, USA

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: How to remove treble action
« Reply #3 on: May 12, 2016, 12:38:42 PM »

Is hard Brass really the best material?
The original material did not work.  (In the long run)
 Is not it better to upgrade one step at a slightly stronger material? 

I have the same problem on an old Koch that I  will try to fix, . . .   soooon  I belive.   

And then corners on an even older Gessner.
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: How to remove treble action
« Reply #4 on: May 12, 2016, 12:47:31 PM »

On some cheaper models they are made of zinc which is rather weak.  Brass ones  on older instruments are better. Probably wise to make them thicker than the originals. In reality it is a poor design, screws through the ends as on a modern one row, or pins are both better.  It all depends on Franks intended use for the box, and how much it will be played.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Frank Bruce

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: How to remove treble action
« Reply #5 on: May 12, 2016, 05:13:01 PM »

Many thanks for the replies. The action has to come out as there are broken and missing springs and it feels as if there is gloop of some sort in there. Not sure what I'm going to clean it out with but I've got a chuck and also one of the ball inflater needles - so hopefully one of these will get the axle out. I don't think it is brass.

As for the latches - I have put new gasket to replace the old leather, so it will need a bit more pressure, so I will maybe go for a thicker brass to hold it firmly. All the old latches have broken off apart from one - they do look a bit thin and cheap, as do the corner things. Theo is right - a bad design. I've glued in some little bits on the inside to strengthen it up a bit.

I haven't thought about how much I will use. It won't be heavy use however - I'm afraid I was just seduced by the fancy inlay! From what I can tell, though, the reeds have a nice 'old' sound.
Logged

Frank Bruce

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: How to remove treble action
« Reply #6 on: May 12, 2016, 10:23:48 PM »

I've had a go at the axle with no joy - my needle thing was maybe not long enough. I'll have to see if I can get something longer that has the same strength. I wonder if one end might be threaded to keep it in. Or is there a chance I could get the defective springs out without taking the rest out.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: How to remove treble action
« Reply #7 on: May 13, 2016, 12:07:58 AM »

I wonder if one end might be threaded to keep it in. Or is there a chance I could get the defective springs out without taking the rest out.

I would doubt very much that it is threaded. It should be possible to replace springs without having to remove the rod.
Logged

Frank Bruce

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: How to remove treble action
« Reply #8 on: June 23, 2016, 08:58:15 PM »

For anybody who might face this problem, here is the end of the saga. I ended up sending the treble end off to my brother who is a clock-maker. He had offered to try and remove the axle with special tools he felt could do the job. They didn't - he said the problem is that the tannins in the wood action would have corroded the metal so there would be twenty-one little bits of corrosion all along it. His all or nothing solution was to remove a bit of the wood covering to get decent access, and give the rod a hard dunt - it worked - and replace the little bit of wood. He has now put in a brass rod which he says won't corrode.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: How to remove treble action
« Reply #9 on: June 23, 2016, 10:05:14 PM »

I've used a car battery with jump leads connected to each end of the axle (on an Oakwood!!!). Much smoke ensued but it did free it off just enough to drift out, but a very large mallet was needed.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: How to remove treble action
« Reply #10 on: June 24, 2016, 11:11:26 AM »

I've gently tapped one out with a bicycle spoke before now, then used the (stainless steel) spoke to replace the axle.

Frank Bruce

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: How to remove treble action
« Reply #11 on: June 24, 2016, 12:34:16 PM »

I like the battery idea just for the sake of using my jump leads for something novel.

I did get a bicycle spoke on the promise of playing a shanty on the repaired instrument to the bike shop owner, but the spoke diameter was too big. A spoke would have been good though as it has a nice curl on the end to make future removal easier - also not likely to corrode.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: How to remove treble action
« Reply #12 on: June 24, 2016, 02:04:18 PM »

On the one-row building course, Emmanual Pariselle used bicycle spokes for the axles.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: How to remove treble action
« Reply #13 on: June 24, 2016, 06:38:38 PM »

"On the one-row building course, Emmanual Pariselle used bicycle spokes for the axles"

Double butted ?
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: How to remove treble action
« Reply #14 on: June 24, 2016, 08:19:42 PM »

"On the one-row building course, Emmanual Pariselle used bicycle spokes for the axles"

Double butted ?

15/17 gauge, chrome plated   ;)
Logged

gettabettabox

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 684
Re: How to remove treble action
« Reply #15 on: June 24, 2016, 08:54:10 PM »

I've used a car battery with jump leads connected to each end of the axle (on an Oakwood!!!). Much smoke ensued but it did free it off just enough to drift out, but a very large mallet was needed.

two ''on the lash'' melodeon fettlers with jump leads walked into a pub.
''two pints please mate''
barman says ''look lads...i'll serve you,... but don't start anything...''
« Last Edit: June 24, 2016, 08:58:34 PM by gettabettabox »
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: How to remove treble action
« Reply #16 on: July 25, 2016, 02:05:30 AM »

Have used the jumper lead trick several times in the past. Sometimes it was a bit brutal getting the rod out, but I was working on 20 inch long rods. I found that heating it several times with a 2-3 mi pause in between almost always works.
 Twisting the heated rod while pulling works best. If can get a chuck on it I will spin it while pulling.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal