Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Simple tuning table  (Read 1152 times)

0 Members and 1 Guest are viewing this topic.

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Simple tuning table
« on: May 24, 2016, 04:09:22 PM »

Hi,
Pictures of a simple tuning table with foot pedal. Made from an old school examination desk, old bellows, a few bits of wood and three door hinges. I might raise it a bit higher or simply mount the pedal and bellows under my bench. But it does work pretty well and functionally is the same as Theo's  ... ( because I borrowed his design ...)
https://goo.gl/photos/ACHBkNaJSSune5so6
« Last Edit: May 24, 2016, 04:24:56 PM by RogerThomas »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Simple tuning table
« Reply #1 on: May 24, 2016, 04:26:08 PM »

Nice variation on the theme.

I now have to make a collapsible version that I can take to France for Emmanuel's course in July.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Simple tuning table
« Reply #2 on: May 24, 2016, 04:31:00 PM »

Well this would collapse if I came up with a solution to fix the bellows to the underside of the table. It is hot glued at the moment but I guess it could be screwed...so you'd just need to do a minor bit of assembly when you get there...unless you are flying?
..the desk folds flat.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Simple tuning table
« Reply #3 on: May 24, 2016, 04:51:57 PM »

Mine is similar, but a tabletop version with a handle underneath. This has serious drawbacks, as the top tends to fill up with cr*p and tools etc and I have to keep tidying it  8) I had intended to use a bungee to bring it back up, but haven't quite bothered yet.

Interested to know what diameter holes you have in the top? I think mine are 11mm but I sometimes wonder if that's too small.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Simple tuning table
« Reply #4 on: May 24, 2016, 05:24:44 PM »

12mm. The desk is a bit low - my bench is 90cm high, whereas 'standard' table height is quite a bit lower. If I can bring myself to drill holes in my custom bench i might stick the bellows under there. I don't think it would matter either if they were set lengthways on.

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Simple tuning table
« Reply #5 on: May 25, 2016, 07:58:54 AM »

Mine has several hole arrangements with sliding air cutoffs. A double one for tuning pairs,a slightly larger one for single larger left side reeds ,and a big one for bass reeds. I also have several adjustable adapters for tuning plate reeds and bass pairs. The bellows are suction/pressure driven by a blower with a shuttle valve that allows me to instantly flip the air direction.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Simple tuning table
« Reply #6 on: May 25, 2016, 09:01:08 AM »

Yes I've seen your adjustable adapters for reed plates. I have an assortment of blocks/slots and gaskets for same. But I am interested to hear that you pump your 'bellows' electrically? I've tried driving an air table with a pump but even though I muted the motor so you can barely hear it, the sound of the air moving in an out of the table is too much, and in any case it doesn't give consistent readings. I've managed to get control of the motor speed etc, but at the end of the day the foot bellows are great...so I give up on the air pump table (:) I mean if I had endless time to develop it...but I don't...
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal