Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Attaching plastic valves  (Read 3063 times)

0 Members and 1 Guest are viewing this topic.

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Attaching plastic valves
« on: June 25, 2016, 06:45:18 PM »

Hi all,
I'm about to start sorting out the reeds in one of my old boxes. I am getting some valves and was wondering what type of glue I should use to attach them to reeds with. If anyone could enlighten me I would be very grateful.
Cheers
Mr hohner
Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Attaching plastic valves
« Reply #1 on: June 25, 2016, 06:47:29 PM »

I use EvoStik Impact

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Re: Attaching plastic valves
« Reply #2 on: June 25, 2016, 07:32:39 PM »

I use EvoStik Impact



Thanks Lester, I'll try using that.
 :||:
Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Attaching plastic valves
« Reply #3 on: June 25, 2016, 08:14:45 PM »

I clamp the tube in my bench vice, give it a little squeeze to get a blob of glue on the tip, wipe the valve across the blob, stick it on the plate.

Ebor_fiddler

  • Chris
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2340
  • Hohner 1040 C One-Row, Sandpiper D/G, Liliput C/F
    • Ebor Morris
Re: Attaching plastic valves
« Reply #4 on: June 30, 2016, 11:42:44 PM »

Yes, as little as you can get away with.
Logged
I'm a Yorkie!
My other melodeon's a fiddle, but one of my Hohners has six strings! I also play a very red Hawkins Bazaar in C and a generic Klingenthaler spoon bass in F.!! My other pets (played) are gobirons - Hohner Marine Band in C, Hohner Tremolo in D and a Chinese Thingy Tremolo in G.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Attaching plastic valves
« Reply #5 on: July 03, 2016, 06:32:03 PM »

Hi all,
I'm about to start sorting out the reeds in one of my old boxes. I am getting some valves and was wondering what type of glue I should use to attach them to reeds with. If anyone could enlighten me I would be very grateful.
Cheers
Mr hohner
We covered this in the melodeon maintenance day which Rees and I held in Mendlesham back at the end of March. You were there - did you nod off at that stage?  ;)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Attaching plastic valves
« Reply #6 on: July 03, 2016, 09:55:20 PM »

An alternative to Impact is UHU, smeared in blobs on a sheet of card. You'll get a few valves out of each blob before it dries.  UHU sets hard so it's a bit closer in property than Impact to the brown shellac you often find on old valves. I think it sets faster than Impact as well, so for me is easier to use, but that is just my opinion. They both give off fumes and impact is particularly horrible after a while. I have also used Bostik solvent free, which has a longer setting time, but it doesn't set hard (neither does Impact) and is difficult to clean off, as is Impact.

mr hohner

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 189
  • K.BLAND Melodeons
Re: Attaching plastic valves
« Reply #7 on: July 04, 2016, 09:15:37 AM »

Hi all,
I'm about to start sorting out the reeds in one of my old boxes. I am getting some valves and was wondering what type of glue I should use to attach them to reeds with. If anyone could enlighten me I would be very grateful.
Cheers
Mr hohner
We covered this in the melodeon maintenance day which Rees and I held in Mendlesham back at the end of March. You were there - did you nod off at that stage?  ;)

I lost the notes I made at the event... That my excuse...   ;)
Logged
Castagnari Studio D/G, Serenelli D/G, Hohner Pokerwork D/G, Castagnari Lilly D/G , Sandpiper Dublin II G/C, Serenelli Silyvia G/Acc

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Attaching plastic valves
« Reply #8 on: July 04, 2016, 09:42:46 AM »

An alternative to Impact is UHU ...  UHU sets hard ...

... which is why I would actually think you should avoid it. It dries hard, and is more prone to getting brittle when used on aluminium and plastic. The wonders of Impact or Bostik Contact #5 is, that it never dries hard, and will stand flexing for years and years.

My personal favorite method is to squeeze out a drop off the tip of the tube, take the drop with a cottonbud/Q-tip, and use that to apply it to the valves. It's faster than it sounds like, and will allow spreading in a thin, even layer, and control how far up the valve you want the glued surface to be.
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Attaching plastic valves
« Reply #9 on: July 04, 2016, 09:43:44 AM »

I use Bison Kit Universal; it's a contact rather than an impact adhesive, slightly easier (IMHO) to work with than Evo-Stik, and much easier to clean off if when you have to.

Graham

(Incidentally I use pretty much the same technique as Lars, except that I use a cocktail stick rather than a cotton bud)
« Last Edit: July 04, 2016, 09:46:43 AM by GPS »
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Lars

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 797
Re: Attaching plastic valves
« Reply #10 on: July 04, 2016, 01:21:19 PM »

I except that I use a cocktail stick rather than a cotton bud)

I tried that, but I found that a cotton bud was better at holding on to excess glue - a plain stick just moved the blob around, whereas the cotton bud would 'dispense' glue in a more even layer. Maybe I'm just too used to the feel of the cotton buds? As with most things in the world of reedwork, doing things 2000 times makes the fingers to for the 'feeling' more than anythings else.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Attaching plastic valves
« Reply #11 on: July 04, 2016, 03:55:37 PM »

I except that I use a cocktail stick rather than a cotton bud)

As with most things in the world of reedwork, doing things 2000 times makes the fingers to for the 'feeling' more than anythings else.

Worth every minute when you get "the feeling".
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Attaching plastic valves
« Reply #12 on: July 04, 2016, 05:19:29 PM »

now't like a good 'feel'!

george ;)
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal