Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Holding bellows open to work on them  (Read 1425 times)

0 Members and 1 Guest are viewing this topic.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Holding bellows open to work on them
« on: August 29, 2016, 04:59:45 PM »

Does anyone have any jigs, tips or methods to hold a bellows stretched open, for repair and the like?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Holding bellows open to work on them
« Reply #1 on: August 29, 2016, 05:34:58 PM »

Only had to do it once -

Took some broken bicycle spokes (available if you are a bit on the heavy side (:) )
Poked 4 of them across the bellows frames through the bellows pin holes
Cut two bits of 1/2 x 1/2 to a suitable length and notched the ends and played them through the bellows to engage with the spokes

 

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Holding bellows open to work on them
« Reply #2 on: August 30, 2016, 06:47:36 AM »

Easy to make, sized to fit specific bellows. 1. Cut slats to fit short dimentions of bellows end frames, two for each end, with blunt taper on short edges of slats which will fit inside bellows where they attach to bellows frames.
2. Cut wooden dowels to the length you wish to extend the bellow to. Slightly taper the ends of dowels to fit undersized holes drilled in the center of the face of slats made on step 1
3.fit two slats in each end of bellows as described in step 1
4 insert dowels inside bellows, slightly overextend bellows to allow fitment of tapered dowel end onto holes in end slat pairs. Do this for both stats/dowel pair.
This works well for holding bellows open to work on the outside of the bellows ,such as retaping,repapering, metal corner work, gusset repair.
If working on the inside of the bellows, I clamp slats to the outside of the bellows frames which extend beyond the width of the frames. On the outside of the bellows, I use either dowels in a method simiar to that described inside the bellows or I have bar clamps which can be used as spreaders between the slats to hold the bellows open for inside side work such as patching. By using two pairs of spreaders for one set of bellows, if one set temporarily interfers with the work area, it can be repositioned as needed.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Holding bellows open to work on them
« Reply #3 on: August 30, 2016, 06:53:18 AM »

 I like Lester's spoke idea. Many of the bellows I have repaired were too old to have been attached with pins, hence the method I described in my previous post on this thread. Spokes are a great material to have around the shop. I have used them to make many things,  including drills to make curved holes.
Logged
I'm squeezin' and they're wheezin': old junker boxes

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Holding bellows open to work on them
« Reply #4 on: September 01, 2016, 08:10:02 AM »

Thanks for the suggestions.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Holding bellows open to work on them
« Reply #5 on: September 04, 2016, 07:32:21 AM »

I like Lester's spoke idea. Many of the bellows I have repaired were too old to have been attached with pins, hence the method I described in my previous post on this thread. Spokes are a great material to have around the shop. I have used them to make many things,  including drills to make curved holes.

I'd be interested to see one of your 'drills to make curved holes'...

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Holding bellows open to work on them
« Reply #6 on: September 07, 2016, 10:23:39 AM »

I like Lester's spoke idea. Many of the bellows I have repaired were too old to have been attached with pins, hence the method I described in my previous post on this thread. Spokes are a great material to have around the shop. I have used them to make many things,  including drills to make curved holes.

I'd be interested to see one of your 'drills to make curved holes'...
The drill itself is not curved, but needs to flex and rotate without breaking. The spoke end is shaped and sharpened. The curved hole is made by creating a bend in the drill while rotating the drill bit as the material is being drilled. A tight radius curve in thick material in not possible with this type drill.
Logged
I'm squeezin' and they're wheezin': old junker boxes
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal