Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Tech advice requested: Connecting mic output cable to mixing desk  (Read 5089 times)

0 Members and 1 Guest are viewing this topic.

Jack Humphreys

  • Hero Member
  • *****
  • Online Online
  • Posts: 709
    • tunesbyjackhumphreys
Re: Tech advice requested: Connecting mic output cable to mixing desk
« Reply #20 on: October 31, 2016, 12:05:49 PM »

Re Microvox

Before I knew anything about all this, using an  old Microvox kit (Velcro !!!) I just used two simple 1/4 jack plug leads, one from each side of the melodeon and straight into the mixing desk.  This works fine, but sound quality seemed a bit basic.  Plus M. Loffet is very condemning of Microvox quality. So this complicated saga is a vanity project trying to improve quality on the few times I perform every year.

Further gratitude  to Howard, Clive et al  for the latest batch of advice.  I think I'm clear now about fitting up my AKG.  This is getting seriously pricey though. Hope this will serve as guidance or a warning to all our readers.

 The main lesson for me is to get the advice and make a plan BEFORE sending off for components...... as returns don't get you back the original cost.  It's all too easy to  rashly click and spend on the internet.  :|bl

Clive Williams

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3936
    • Home Page
Re: Tech advice requested: Connecting mic output cable to mixing desk
« Reply #21 on: October 31, 2016, 12:24:43 PM »

Another thought - when I do install this kit - does that make it a useful thing for recording for youtube- or am I better off using the USB Yeti Mic I already have?

I have an (old) AKG setup with DI box for live use, and the sound is good as you would expect... but youtube recordings are a different beast - the AKG brings out too much mechanical noise which is nowhere near as obvious in a live context. I prefer to use a USB microphone (in my case a Zoom H2), which is much easier to setup too.

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Tech advice requested: Connecting mic output cable to mixing desk
« Reply #22 on: October 31, 2016, 05:33:40 PM »

Whether you use a DI box or not will have little or no effect on the sound quality, in fact a low quality active DI box may add some noise. It will however always help with noise pickup (mains, light dimmers, taxis...).

Many desks only have balanced XLR inputs, and anywhere with a PA run by a sound engineer will want either XLR outputs or will provide you with a DI box to turn your unbalanced jack signal into a balanced XLR signal.
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

fishfeathersmacteeth

  • Member
  • *
  • Offline Offline
  • Posts: 28
Re: Tech advice requested: Connecting mic output cable to mixing desk
« Reply #23 on: November 24, 2016, 09:59:30 AM »

Thread drift warning:

There are stories, some perhaps apocryphal, of PA systems broadcasting taxi radios as they drive past.

Rob.

We used to do a regular gig at a church hall in Stockport (so good they named it once...).  The sound check was frequently enlivened by extracts from early evening mass in the adjacent church,  Modern priests and their radio mikes, eh.... :|glug

I know where you mean.  When we played there, someone came round to complain the sound check was interrupting mass...

So who changed channels....?  8)
Logged
...been here and gone...All the way from Luthermuir..Fiddle player, Harmonica wheezer and Melodeon wrestler

B/C Double-Ray Black Dot; B/C Organola B/C 36 Bass; Frontini B/C; Casali B/C/C# 48 Bass; Hohner Club II C/F and a bit
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal