Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Pastourelle II Button Diameter  (Read 1525 times)

0 Members and 1 Guest are viewing this topic.

dave t

  • Good talker
  • **
  • Offline Offline
  • Posts: 92
  • DB Oakwood Super III/Pastourelle II
Pastourelle II Button Diameter
« on: November 21, 2016, 05:46:37 PM »

I have a Saltarelle Pastourelle II and I am considering changing the buttons from white to black. However, I need to know the exact diameter of the buttons down to the half millimetre and I don't have anything that will measure that accurately. Does anyone have a Pastourelle II who would be able to take that measurement for me?

Thanks, Dave
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Pastourelle II Button Diameter
« Reply #1 on: November 22, 2016, 01:12:51 AM »

A vernier gauge or decent steel ruler...the little 150mm ones... would give you accurate enough measurement. And of course there is no guarantee that all Pastourelle buttons are the same.
...like this...a very useful tool...https://www.ebay.co.uk/itm/122154701120
« Last Edit: November 22, 2016, 06:38:13 AM by RogerT »
Logged

dave t

  • Good talker
  • **
  • Offline Offline
  • Posts: 92
  • DB Oakwood Super III/Pastourelle II
Re: Pastourelle II Button Diameter
« Reply #2 on: November 22, 2016, 07:44:26 AM »

Thanks Roger. I was trying to avoid having to buy a tool that I would never use again! But I'll see if I can try and get a measurement that is accurate enough using a steel ruler, unless any other Pastourelle owners out there can help out.

Dave
Logged

Julian S

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1628
  • D/G Pastourelle 2, Dony, Pokerwork, G/C Pariselle
Re: Pastourelle II Button Diameter
« Reply #3 on: November 22, 2016, 07:54:50 AM »

I will measure mine - but because Saltarelle boxes are made by different manufacturers it's quite possible they are different sizes. Age of yours ? Mine is getting on thirty years old.
I've been living with one bass button being slightly larger than the others for years - I did buy replacements so that they all would be bigger but the shape was different, with a sharper edge which actually felt uncomfortable compared to the originals...
Logged
Old Bones Dance Band

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Pastourelle II Button Diameter
« Reply #4 on: November 22, 2016, 08:07:39 AM »

Or send a sample  button to your supplier if black buttons and ask them to match it for size.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Pastourelle II Button Diameter
« Reply #5 on: November 22, 2016, 09:47:26 AM »

You could - tie a slip knot in a piece of thread and loop it over the button and tighten it around the button, then with a fine marker put a dot on the tread next to the knot (the mark has to be pretty small and right up against the knot). Take loop off, open it up a bit and cut it, you then have a measurement of the circumference of the button (between mark and knot), from that you can calculate the diameter.

Or hold a ruler over the centre of button and read measurement, I can get a measure to within a 1/2 mm
Logged

Alyn Iorwerth

  • Member
  • *
  • Offline Offline
  • Posts: 13
Re: Pastourelle II Button Diameter
« Reply #6 on: November 22, 2016, 09:57:37 AM »

Dave,
On my P II, which is around 17 years old, the treble buttons are 15.1 mm, and the bass buttons are 13.4 mm (No, I hadn't noticed until I measured them this morning, but the difference is important, because the spacing is also smaller on the bass end). These are averages based on two buttons measured with a micrometer at each end, which is all I can practicably measure without dismantling. There seems to be a bit of variation from button to button, which is only to be expected.
Hope this helps.
Alyn
Logged

dave t

  • Good talker
  • **
  • Offline Offline
  • Posts: 92
  • DB Oakwood Super III/Pastourelle II
Re: Pastourelle II Button Diameter
« Reply #7 on: November 22, 2016, 07:55:30 PM »

That's brilliant, thanks Alyn. Mine is around 10 years old so hopefully it will be the same but I'll check it with a steel ruler. And thanks for the other suggestions everyone.

Cheers, Dave
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal