Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Sticking Register Slides  (Read 2021 times)

0 Members and 1 Guest are viewing this topic.

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Sticking Register Slides
« on: November 28, 2016, 12:40:16 AM »

Greetings!
    I am new to the forums and am grateful to have found this resource! 
    I've repaired 2 piano accordions for my own use...to learn on.  Now I am working on a friends C. Bellini 1 row diatonic button accordion with 3 registers and bass spoons (not buttons!) I'm guessing 70 years old or so.  The register slides are wood and are so very difficult to move. I am not sure how remedy this and make them easy to slide. Can anyone lend some advise?
Thanks 
Logged
Hohner Club IIB Victoria

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Sticking Register Slides
« Reply #1 on: November 28, 2016, 12:53:37 PM »

Not something I've tackled myself.  Your description sounds like a three-stop, similar in construction to a Cajun box.  I have known a few that were not easy to move and if the board has warped it will probably always be that way although it might be possible to rub some candle wax on the slide to reduce the friction.  If the shaft to the stop knob is bent it may be causing friction.  It can be unscrewed and straighted, but it is a delicate job making sure you don't wind it back in too hard so that the slide is out of position.

It is more common that the slides move too easily and there are methods, both low and high tech to hold them still.  These vary from detent stops, strong neodimium (sp?) magnets buried in the casework and clothes pegs on the shaft!

Rob.
Logged

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Sticking Register Slides
« Reply #2 on: November 28, 2016, 04:11:39 PM »



It is more common that the slides move too easily and there are methods, both low and high tech to hold them still.  These vary from detent stops, strong neodimium (sp?) magnets buried in the casework and clothes pegs on the shaft!

Rob.

And the humble red elastic band left by the post man... :|glug
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Sticking Register Slides
« Reply #3 on: November 28, 2016, 04:22:02 PM »

You have limited options for freeing up your register slides as everything is glued together, and there are very thin wooden components in there that have to be treated gently. As the previous reply has suggested the first thing to ensure is that the shafts that emerge through the farm of the box are free to move, corrosion and damage can make them tight.

As to the slides themselves I would prefer to use graphite or powdered PTFE as dry lubricants, but it's not an easy one to fix. Good luck!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Sticking Register Slides
« Reply #4 on: November 28, 2016, 04:42:29 PM »

Thanks everyone. I suspected all those parts were glued, but had not considered corrosion on the shafts. Since most all other metal components on this machine have corrosion, to some degree, I have to assume a high likelihood of the shafts being corroded.  Will examine for that during the next work session. Again...thanks!
« Last Edit: November 28, 2016, 11:14:39 PM by Barry Tolson »
Logged
Hohner Club IIB Victoria

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Sticking Register Slides
« Reply #5 on: November 28, 2016, 11:09:36 PM »

Update:
   I just had a work session and first removed the knobs and cleaned one of the rods/shafts with a q-tip dipped in a very mild detergent solution...the portion of the rod/shaft that is outside the instrument.    Lots of dirt came off the shaft and onto the q-tip. I did this until no more dirt came off.  There was no change in the movement after the cleaning.
   Then I cut a narrow strip of very very fine sandpaper and looped it around the rod/shaft and carefully worked my way around until there was no corrosion, just a shiny surface. This made a huge difference!  But...I saw further room for improvement.
   After pondering a few moments, I decided to then take a small piece of pure beeswax and rub it lightly all around the shaft/rod.  Smooth as silk!!!! (and not too loose!)
    One rod down...and two to go!  Should have this work finished by bedtime!!! 
Thanks again everyone for guiding me! 
    I had assumed it was a problem with the slide, when it seems now that the problem was obstruction caused by the dirt and corrosion.
Logged
Hohner Club IIB Victoria

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Sticking Register Slides
« Reply #6 on: November 29, 2016, 06:37:30 PM »

And the humble red elastic band left by the post man...

Sadly although thousands end up thrown into my frony garden our local sorting office seems to have done a deal on time expired elastic bands - thy're hard and brittle.

Glad to hear the slides are moving again.  It may still be that the slides are in fact slightly warped, but if cleaning the rods makes them functional then job's a good'un!

Rob.
Logged

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Sticking Register Slides
« Reply #7 on: December 02, 2016, 12:40:34 AM »

One of the blocks that are adhered to slides...the blocks into which the push rods are screwed...has come unattached from the slide.   Can anyone recommend the substance that is used to adhere those blocks to the slides?  Regular modern wood glue? Hide glue? Something else?
Logged
Hohner Club IIB Victoria

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Sticking Register Slides
« Reply #8 on: December 02, 2016, 09:47:51 AM »

Hide glue would have been used originally.  If you have some handy it will work for a few decades quite securely.  Other glues may be less successful if there are any traces of the hide glue left.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Sticking Register Slides
« Reply #9 on: December 02, 2016, 10:35:33 AM »

Thanks Theo. Hide glue it will be, then!
Logged
Hohner Club IIB Victoria
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal