Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner Compadre modifications  (Read 1943 times)

0 Members and 1 Guest are viewing this topic.

deltasalmon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1002
Hohner Compadre modifications
« on: December 23, 2016, 10:13:16 PM »

I recently purchased a Hohner Compadre in ADG. Seems to be a nice box so far but I think there are a few small modifications I could do that could make it better.

The first peculiar thing about the box was that the bass strap, which is adjustable, was too big for me even when I made it as tight as possible. I'm 6'5" and about 260 lbs so this came as a surprise. It turned out to be an easy fix to trim the bass strap and now fits great.

The second peculiarity is the thumb strap. I've had boxes with them before and I usually take them off as I don't use them ever. This is typically done by just removing two screws and it's done. The Compadre thumb strap is riveted in (see pictures). Is there any easy way to remove rivets or should I just get used to playing with the thumb strap still on?

The last modification I'd like to do is to restrict the button movement. I've seen it said on here that you can put felt on the back. Should I look to find felt that is similar to the felt that is already on it? How should I adhere the felt to the bottom of the keyboard? Do I remove the old felt first or just throw the new felt on top of the old?

I can't seem to attach the pictures but they can be viewed here:
http://mcginnis.xyz/pic1.jpg
http://mcginnis.xyz/pic2.jpg

Cheers,
Sean
Logged
Sean McGinnis
Bordentown City, NJ, USA

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Hohner Compadre modifications
« Reply #1 on: December 23, 2016, 10:25:17 PM »

To remove the rivets you will need to drill them out from the inside. I normally cut the leather off so the outside of the rivet sits proud and then you can grasp the rivet head with a pair of pliers as it will invariably rotate otherwise.

As to the felt you need to find some felt of the correct density and thickness which can be a challenge, it can either be stuck to the existing felt or the existing felt can be removed.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner Compadre modifications
« Reply #2 on: December 23, 2016, 11:47:18 PM »

The best source for felt is from piano tuners' or repairers' suppliers. It is available in different widths, thicknesses and degrees of firmness (hard, soft, etc.)
In the US, try here:
Piano Forte Supply.

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

ACE

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 535
Re: Hohner Compadre modifications
« Reply #3 on: December 24, 2016, 08:19:32 AM »

My compadre needed the button travel adjusted, it did not need much. I used the sticky back felt that you can get for sticking to the bottoms of stuff to stop them scratching the furniture and stuck it over the existing felt. I did not want to leave a hole where the thumb strap is so I just spun it out of the way and use a dot of double sided sticky tape, even a bit inside the strap to make it lay flatter. I only done this as it was not a keeper, if you are keeping it the small hole can be filled I suppose. I also found  the original seat belt shoulder straps kept rucking up, so a cheap pair of Chinese PA straps replaced them.  Be very careful of the gig bag they come with, the sewing to the carry straps is very poor and will rip out easily and the cheap buckles are brittle and break. The instrument itself is very good for the money you pay. if you use a microvox the M305/310 will take some very careful placing to use all 3 rows.
Logged
Paddy Clancy, paddlewheel gob iron cheepo g/d anglo

deltasalmon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1002
Re: Hohner Compadre modifications
« Reply #4 on: December 26, 2016, 03:09:34 PM »

Thanks for the advice everyone. The felt seems like something I can definitely do. I can take just the back of the keyboard to a local craft shop and see if they can help me match new felt for it.

The thumb strap I'll probably cut off. The rivets I'll just leave until a day when I'm feeling especially adventurous.

Be very careful of the gig bag they come with, the sewing to the carry straps is very poor and will rip out easily and the cheap buckles are brittle and break.

I'm surprised to hear this about the bag. The straps that came with it are awful but when I saw the bag it came with I was actually surprised in how good quality it seemed (especially compared to the Hohner bag I have that fits a pokerwork sized accordion). I'm wondering if we're actually talking about the same bag?

In general though, I'm very happy with the purchase.
Logged
Sean McGinnis
Bordentown City, NJ, USA

ACE

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 535
Re: Hohner Compadre modifications
« Reply #5 on: December 26, 2016, 08:56:15 PM »

That looks like a far better bag than the one I got with mine, which was quite a flimsy affair and a top loader which was just a flap, no zips.
Logged
Paddy Clancy, paddlewheel gob iron cheepo g/d anglo
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal