Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Getting pallets airtight on a one row 4 stopper?  (Read 4052 times)

0 Members and 1 Guest are viewing this topic.

911377brian

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1518
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #20 on: March 26, 2017, 08:25:55 PM »

That's clever...
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #21 on: March 26, 2017, 10:06:17 PM »

We use a stethoscope that has had the metal end cut off and replaced with a 1/8 metal tube. You squeeze the accordion and pass the tip of the tube around the possible leak areas.

You will readily hear air blowing over the end of the tube and you can pinpoint leaks.
Great idea. Now where can I get my hands on a stethoscope....

Bill Young

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1151
  • Paolo Soprani BCC#
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #22 on: March 26, 2017, 10:31:46 PM »

Great idea. Now where can I get my hands on a stethoscope....
Remarkably cheap on eBay.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #23 on: March 27, 2017, 05:27:54 AM »

This thread high lights the problems that arise when doing things on keyboards. It occurs to me to ask if you have the keys back on the spindle/axle in exactly the same order that you took them off? If you haven't that is the reason why they leak. Each one will have been individually fitted.

TomBom

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 471
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #24 on: March 27, 2017, 12:50:07 PM »

Oh yes, I numbered the lever arms and put them back in the same order.
Logged

TomBom

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 471
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #25 on: March 27, 2017, 10:19:58 PM »

Success! I got it reasonably airtight. If I push the bellows really hard some of the highest reeds will start sounding and I can hear air flowing out (not sure about how to say this in English). It's ok for now.
Thanks for your help. I tried taking out the reed blocks and using a strong light - this is obviously no method for me ... Using Steve's paper method helped to identify the leaks.
After that: bending the rods. After a while I was able to get a feel for how much bending is making a difference.
Unfortunately not very much differnce in spring tension. I mean the springs are not much softer than before.
Logged

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #26 on: March 30, 2017, 08:31:20 AM »

I agree with Roger - diagnose the problem first.
The location and extent of leaky pallets can be best found by using a 'Rizla'-type cigarette paper: cut a narrow tapering strip the length of the paper and about 5 mm wide at the narrow end and about 10 mm wide at the other end.

Use this as a feeler gauge by inserting the strip underneath the pallet and letting the spring tension 'grab' the paper. Try pulling the strip out and get a feel for the amount of grab. If there is any leak the strip will come out easily or not be held at all. Repeat the test in different places around the pallet and do the same on every pallet. This should enable you to accurately locate problem leaky places.

It's not really possible to recommend a solution until you have determined the cause/location of the leaks.
A more durable alternative to cigarette paper can be made by substituting a strip of mylar or a section of magnetic recording tape for the paper. Mylar is often used for decorative balloons. I like using a strip of magnetic recording tape gleaned from an audio cassette. The flexible feeler guage can be attached to end of a small dowel. This tool also works well for checking for leaking pads on woodwind instruments.
« Last Edit: March 30, 2017, 08:33:13 AM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes

Malcolm Clapp

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1119
  • Loving my Hohner-reeded wet MMM CastaTommy
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #27 on: March 30, 2017, 10:08:34 AM »


A more durable alternative to cigarette paper can be made by substituting a strip of mylar

Or possibly a strip cut from a floppy disc....

They aren't much use for anything else afaik, except perhaps as an emergency supply of flap valves?

(Edited to apologise in advance, should this thread becomes hijacked by those who have found really inventive uses for old floppies....)
« Last Edit: March 30, 2017, 10:12:13 AM by Malcolm Clapp »
Logged
Tuner/repairer, now retired.

TomBom

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 471
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #28 on: March 30, 2017, 11:02:22 AM »

A more durable alternative to cigarette paper can be made by substituting a strip of mylar
Next time I change my banjo head I'll cut off a strip to make a feeler gauge.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #29 on: March 30, 2017, 11:48:33 AM »

I agree with Roger - diagnose the problem first.
The location and extent of leaky pallets can be best found by using a 'Rizla'-type cigarette paper: cut a narrow tapering strip the length of the paper and about 5 mm wide at the narrow end and about 10 mm wide at the other end.

Use this as a feeler gauge by inserting the strip underneath the pallet and letting the spring tension 'grab' the paper. Try pulling the strip out and get a feel for the amount of grab. If there is any leak the strip will come out easily or not be held at all. Repeat the test in different places around the pallet and do the same on every pallet. This should enable you to accurately locate problem leaky places.

It's not really possible to recommend a solution until you have determined the cause/location of the leaks.
A more durable alternative to cigarette paper can be made by substituting a strip of mylar or a section of magnetic recording tape for the paper. Mylar is often used for decorative balloons. I like using a strip of magnetic recording tape gleaned from an audio cassette. The flexible feeler guage can be attached to end of a small dowel. This tool also works well for checking for leaking pads on woodwind instruments.
Crumbs - that sounds like overkill to me. As a wind player I've always got packets of fag papers knocking around* so it's no problem to slip one out, two snips with scissors and it's ready for use. Easy to put a bend in it for getting in between pallets. Plus the fag paper is really thin and hence very sensitive to different 'grab' settings, which is useful for distinguishing between slight, medium and severe air leaks.

* wind players use them for mopping up condensation and blobs of water on tone hole pads.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #30 on: March 31, 2017, 09:38:12 AM »

I agree with Roger - diagnose the problem first.
The location and extent of leaky pallets can be best found by using a 'Rizla'-type cigarette paper: cut a narrow tapering strip the length of the paper and about 5 mm wide at the narrow end and about 10 mm wide at the other end.

Use this as a feeler gauge by inserting the strip underneath the pallet and letting the spring tension 'grab' the paper. Try pulling the strip out and get a feel for the amount of grab. If there is any leak the strip will come out easily or not be held at all. Repeat the test in different places around the pallet and do the same on every pallet. This should enable you to accurately locate problem leaky places.

It's not really possible to recommend a solution until you have determined the cause/location of the leaks.
A more durable alternative to cigarette paper can be made by substituting a strip of mylar or a section of magnetic recording tape for the paper. Mylar is often used for decorative balloons. I like using a strip of magnetic recording tape gleaned from an audio cassette. The flexible feeler guage can be attached to end of a small dowel. This tool also works well for checking for leaking pads on woodwind instruments.
Crumbs - that sounds like overkill to me. As a wind player I've always got packets of fag papers knocking around* so it's no problem to slip one out, two snips with scissors and it's ready for use. Easy to put a bend in it for getting in between pallets. Plus the fag paper is really thin and hence very sensitive to different 'grab' settings, which is useful for distinguishing between slight, medium and severe air leaks.

* wind players use them for mopping up condensation and blobs of water on tone hole pads.
I've never found a use for for these papers in over fifty five years of playing the french horn, but I can see how they would be useful. I've never smoked, so haven't had them on hand for the intended purpose. Mylar strips are popular with the woodwind repair techs I lnow, for checking for leaks after repading jobs.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #31 on: March 31, 2017, 09:40:13 AM »

A more durable alternative to cigarette paper can be made by substituting a strip of mylar
Next time I change my banjo head I'll cut off a strip to make a feeler gauge.
I use skin heads on my banjos. I think they are too thick for the purpose of checking pallet sealing.
« Last Edit: April 07, 2017, 07:46:00 AM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes

fc diato

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 146
Re: Getting pallets airtight on a one row 4 stopper?
« Reply #32 on: April 11, 2017, 03:36:05 PM »

Thanks to this thread (and all the others I dug up) I finally gathered my courage and took my first plunge into a box to try to fix my leaky one-row.  It was dicey, but I learned a few things that might benefit someone else:
      This is a one-row where the pallets are screwed on, so easy to remove. (Why don’t they always make them like that?)  I noticed the leather and facing were in terrible condition.. box dates from 1995, as I discovered inside. Looks like facing does too- felt is very stiff. I first tried ‘fluffing’ the leather, but that just disintegrated it. No friendly fettler anywhere close, or a place to get materials quickly. So I figured a stop-gap solution was to take leather from a ruined old jacket - I had saved the good pieces, and to glue that on (good enough until proper fix, I gathered? And nothing to lose.)  Oh my!  Even more unplayable. 
     Until I thought of toying with the 2 screws that hold in the pallets. (I had tested with the pallets in place but not screwed in, and everything seemed fine  ???)  Turns out you have to tighten those screws just so the pallet doesn’t wobble on its arm, and not one micro-iota further. No more leaking at all.  If only I had started with that? Oh well, now at least the buttons are a tad lower, which I like. I have a feeling my stopgap will be there for a while. Very pleased right now. :Ph
And vive Melnet!
Logged
fc diato
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal