Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: reed scratcher from drill bit  (Read 3194 times)

0 Members and 1 Guest are viewing this topic.

jorden

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 108
reed scratcher from drill bit
« on: June 05, 2017, 09:58:48 PM »

I'm trying to make a reed scratcher from an old metal drill bit. Do I understand correctly that the end should be circular, but at an 90 degree angle? So basically just a straight 'cut'? I broke a drill bit with a hammer and grinded down the end flat with (a lot of) sandpaper, but the resulting edge wasn't very sharp. Or might it be that the drill bit isn't hard enough?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed scratcher from drill bit
« Reply #1 on: June 05, 2017, 10:30:32 PM »

You must grind the end at 90 degrees using a hard grinding surface such as a grindstone or a diamond sharpening plate, and finish with a middle/fine eg 600 grit stone. Grinding on a paper abrasive will always have a tendency to round the edges.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: reed scratcher from drill bit
« Reply #2 on: June 06, 2017, 07:37:27 AM »

I made some reed scratches from a set of swiss made watch maker's screwdrivers. The screwdriver shafts are like miniature drill rods, while the handles are similar to pin vises with collet chucks. Thus, the amount the scratcher extends from the holder/handle is adjustable.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: reed scratcher from drill bit
« Reply #3 on: May 03, 2019, 01:03:43 PM »

An easy method to make your surface true and sharp is to drill a hole in a piece of scrap plastic of 1/2" or so thickness the same size as the drill rod you're trying to sharpen.  then use that plastic as a guide to run over your sharpening stone. The result is a perfectly square and sharp ended rod.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed scratcher from drill bit
« Reply #4 on: May 03, 2019, 01:51:42 PM »

Thanks Mark, that is a handy tip.

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: reed scratcher from drill bit
« Reply #5 on: May 03, 2019, 02:26:28 PM »

Old needle files make very good scratchers. I sometimes just snap off the very end (with safety specs on, mind, a shard of file steel in the eye can easily blind you, so be bloody careful). The resulting fracture normally has some razor sharp/super hard points ideal for scratching. Also in a set of files (the sort you can pick up for less than £5) one or two already have a super hard sharp point, also very handy as a scratcher. And you can shape the end a bit with a grinding wheel and they already have a handle attached etc.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: reed scratcher from drill bit
« Reply #6 on: May 03, 2019, 03:00:14 PM »

...you can shape the end a bit with a grinding wheel ...

A good touch is required to make sure you don't overheat heat and anneal them.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: reed scratcher from drill bit
« Reply #7 on: May 03, 2019, 04:26:47 PM »

Are you working on the shank end of the drill ?  these tend to be tempered, or not hardened, to reduce the chance of breakage and this extends down the flutes towards the cutting end (how many drill shanks have you seen gouged and ragged up by slipping in the chuck?)

You could try heating them up until they cease to be attracted by a magnet and then oil or cold water quench, water may make them over brittle and oil may flare, make sure you have something to smother it with.

If too brittle you can re temper by sticking the cutting end in a potato by an inch or so and (having polished the other end with a bit of emery, gently heat in something like a meths flame until the oxide colour produced turns blue, then quench. The potato stops the hard end getting hot enough to temper - old watchmakers trick learned from an old watchmaker.

Cooks gas torches used for browning things are ideal for this sort of job.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: reed scratcher from drill bit
« Reply #8 on: May 03, 2019, 04:34:39 PM »

"heating them up until they cease to be attracted by a magnet"

Wow, thanks for that Richard. This heating till cherry red and the like has always been a mystery to me, being colour blind. That's a really useful tip!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: reed scratcher from drill bit
« Reply #9 on: May 03, 2019, 04:54:32 PM »

Its the point where the heat breaks down the structure in the metal which supports magnetism and the structure gets frozen by the quench resulting in max hardness - simples, tempering is the black art bit especially if you are, like the drill manufacturer, looking for a graduated temper on say an edgetool like a scythe or axe, then of course there is the mysteries of annealing, or at our age more probably, asittingdowning  :(

Given the exotic chemicals incorporated in tool steels these days the suggestion of carefully grinding down something like a needle file (if it turns blue you have ruined it, snap a bit off and start again) is probably a better starting point than a drill bit.

None of the above or previous post treatments apply to a high speed steel drill bit.
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed scratcher from drill bit
« Reply #10 on: May 03, 2019, 04:59:26 PM »

I’ve tried making scratcher bits from drill bits and the results have been disappointing.  The tools that Hohner sell with a removable tip are quite good.  The tips are a bit expensive but last a long time.  I’ve now started using a tapered one piece scratcher from Carini which is as good as the Hohner tool for durability of the cutting edge, and beats it on rigidity.  The extra rigidity makes it much easier to use.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: reed scratcher from drill bit
« Reply #11 on: May 03, 2019, 05:06:11 PM »

I make my scratcher from an old high quality tuning file. First I warm it up to a nice dark red and give it a 90 degrees bend at one end. I let it cool down slowly. Now the steel is very malleable making it easy to give it its final shape with a file and sand paper. Once I'm happy with it, I temper it (pink red, cold water shock) and hone the edges.
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: reed scratcher from drill bit
« Reply #12 on: May 03, 2019, 05:23:08 PM »

Has anybody tried a lathe tool holder with a carbide interchangeable tip?

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: reed scratcher from drill bit
« Reply #13 on: May 03, 2019, 06:18:09 PM »

The tools that Hohner sell with a removable tip are quite good.  The tips are a bit expensive but last a long time.

Do you have a link to share for this tool? I’ve been unable to find it myself.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed scratcher from drill bit
« Reply #14 on: May 03, 2019, 06:22:05 PM »

Yes it’s here
http://www.hohner-cshop.de/en/Accordion/Tools/Tuning-Scraper.html

And the price has gone up since I got mine.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: reed scratcher from drill bit
« Reply #15 on: May 04, 2019, 07:17:27 AM »

My vote goes with the Carini tapered scraper re Theo's suggestion. They do a long and a short. They are excellent. One has to be careful though not to snap off the tip, which I stupidly did on one of mine.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: reed scratcher from drill bit
« Reply #16 on: May 04, 2019, 01:13:55 PM »

An engineering tradesman in Lever Brothers (c 1979) taught me how to make a scriber out of a short length of old hacksaw blade - break the blade at a 45 degree angle then take what's left of the teeth off with the bench grinder and then grind a 45 degree (or whatever suits) cutting edge on the broken end.

Hacksaw blades are (traditionally) a plain high carbon steel with the teeth- but not the blade back-blue tempered. Take care not to overheat the blade while you are grinding as this risks annealing the steel.

I made one of these last night to use for scraping old wax off a reed block.
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: reed scratcher from drill bit
« Reply #17 on: May 04, 2019, 02:50:41 PM »

Discarded steel pallet strapping is handy too. I have loads of special tools made from it.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: reed scratcher from drill bit
« Reply #18 on: May 04, 2019, 03:32:34 PM »

Discarded steel pallet strapping is handy too. I have loads of special tools made from it.
I like this approach!
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: reed scratcher from drill bit
« Reply #19 on: May 05, 2019, 03:08:55 PM »

An easy method to make your surface true and sharp is to drill a hole in a piece of scrap plastic of 1/2" or so thickness the same size as the drill rod you're trying to sharpen.  then use that plastic as a guide to run over your sharpening stone. The result is a perfectly square and sharp ended rod.

I’ve just done this and what a difference!  Scratcher is equally sharp all the way round.  Thank you Mark.

I had no hand plastic scrap so I used a piece of high quality 3/4” ply with a melamine surface.

And I’ll add a tip of my own.  After trying many abrasives for this job: oilstone, water stone, diamond plate, the best so far is an Arkansas stone. It’s so hard that the tip has no tendency to dig in and form a groove.  I got this tip from a Belgian wood carver!
« Last Edit: May 05, 2019, 03:12:59 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal