Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Paolo Soprani 2 Voice  (Read 6070 times)

0 Members and 1 Guest are viewing this topic.

Robert Sehy

  • Member
  • *
  • Offline Offline
  • Posts: 11
Re: Paolo Soprani 2 Voice
« Reply #20 on: July 04, 2017, 10:46:38 PM »

Stiamh, did you convert the stepped keyboard to flat on that Paolo?
Logged

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Paolo Soprani 2 Voice
« Reply #21 on: July 05, 2017, 01:40:27 PM »

Stiamh, did you convert the stepped keyboard to flat on that Paolo?

Yes, it was converted, though not by me. I bought the box as a project from Paul Groff, who had had a replacement aluminium keyboard plate made but hadn't gone further than that. The levers on my box are wooden and my repair tech did his best with them. In the end he glued new buttons onto the lever ends. The conversion was not entirely successful in my view because I ended up with an action that is higher than I would have liked.

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Paolo Soprani 2 Voice
« Reply #22 on: July 06, 2017, 12:20:25 AM »

Hi Steve and all,

Sorry to hear that the converted Paolo still doesn't have the "set up" the way you would like it. I wish I had been able to finish that job myself but I had to sell it as a project, at the low ebb of my finances and time/space to work on instruments.

This example shows that there is a lot of custom work (and then sometimes, re-work) to convert a keyboard and then to perfect its set-up.

The best solution to the buttons on that (Steve's) conversion being too high, IMO, would be to change to buttons that are shorter in height, or to sand the existing buttons from the underside to a shorter dimension (thinner, top-to-bottom). I supplied those buttons, as well as the keyboard plate (all made to my specs by superb machinist Henry Szostek). So I could have asked for the buttons to be made shorter, but didn't want them too short -- then the buttons wouldn't be able to project high *enough* above the keyboard plate for some tastes (including mine, because I had hoped to keep that one).

The geometry of the action on an  "enclosed lever, flat keyboard" accordion," with levers under a flat keyboard plate to which are glued buttons that project through holes in the plate, puts a limit on how high you can raise the buttons. Obviously you don't want the levers themselves to hit the underside of that plate, in the region near the buttons where the keyboard isn't drilled for the button holes. Some players like the buttons to extend well above that keyboard plate (for example, in a recent discussion of Primatonas, Mike Hirst was asking how to raise the height of the buttons above the keyboard, and I'm finding the button height on my Amatona is also a little low for me).  So to accommodate that preference, the buttons have to be thick enough.

It is sometimes possible to lower the height of the buttons (without changing their dimensions directly) by adjusting the pallet levers (depending on the geometry of the rest of the box). But Steve's little Paolo has an action with an older design, so I think there may not be sufficient room in the keyboard housing under the wooden levers for those levers to travel substantially deeper. In that case, changing the heights of the individual buttons would be the best way to achieve his target set-up.

To repeat (and as I cautioned Robert via email), there's a lot of custom work needed to complete any of these stepped-to-flat conversions!

PG

edited to add:

Just for brainstorming. One other way to lower the effective button height on an instrument like this would be to shim under the keyboard plate, raising that plate relative to the plane of the button tops. In the case of Steve's instrument, the keyboard plate is part of a rather complex and partly-curved piece of aluminum so the entire piece might have to be modified slightly (or switched for another one) to try this solution - thus I'd recommend changing the button thickness instead.
« Last Edit: July 06, 2017, 12:29:05 AM by pgroff »
Logged

Gary P Chapin

  • L'Accordéonaire
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1950
  • We are all the Free Reed Liberation Orchestra
    • Accordeonaire -- my blog of the last 15 years
Re: Paolo Soprani 2 Voice
« Reply #23 on: July 06, 2017, 03:24:57 AM »

This is a great thread. I am learning a huge amount. Carry on.
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal