Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Harmonikas Nastrino A Mano  (Read 6927 times)

0 Members and 1 Guest are viewing this topic.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Harmonikas Nastrino A Mano
« Reply #20 on: October 26, 2017, 08:34:55 PM »

There may be other factors, but the fit on both the A Mano Professional and the Dix reeds seem very good, as far as reed to slot fit.  The dimensions of the Professional reeds (width and length) are close to the dimensions of the Binci a manos.  The Dix are smaller, very similar to the old German reeds they are reproductions of, and the sides of the reed tongues are parallel as opposed to tapered.  Response of both seem similar to me, but the professionals are much louder with a good punch.  Tone is similar with the professionals having a crisper sound.  I am ordering some Nastrinos and will put in the same box as I have the professionals in to see the difference.

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Harmonikas Nastrino A Mano
« Reply #21 on: October 26, 2017, 11:33:23 PM »

Following your logic.. is it possible that the "dural" range of reeds could be more exactly fitted and tuned to the same degree as a more expensive reed and potentially yield better than "usual" ( for dural) results. ?

I have played many fine boxes with DURAL quality reeds. Also played many boxes with Binci Pros and other high quality reeds that have been simply acceptable.

If the materials are the same, very probably. But if the reed or frame material is different, maybe not. Of course it all depends what you mean by "better" -- sweeter, brighter, faster, louder...

Expert fettling makes as much -- or maybe more -- difference to the sound as the reed quality/cost. A cheap low-quality reed which has big clearances to the frame will never be capable of responding as quickly as an expensive high-quality reed with tighter clearances. And some people obviously prefer the softer sound of cheaper reeds as opposed to the brighter sound of expensive ones...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Harmonikas Nastrino A Mano
« Reply #22 on: October 31, 2017, 08:26:54 PM »

Expert fettling does indeed lift the sound quality of a so-so reed, ideally making the tone produced the same throughout the range.  In some ways what is more delightful about a set of freshly set-up reeds is the even responsiveness across the range, perhaps the pleasure of playing colours one's perception of the tone?  I had an indifferent Nik (dural reeds) which after a full reed tune and set-up was lovely to play and seemed to sound so much brighter.  Some observers didn't notice any difference, so perhaps it was more capable and so pleased my ear when I played it.

My later box with VA TaM reeds was a sheer delight to play from new and had a dynamic range from a husky whisper to so loud it felt like a chisel rammed in your ear!  The Nik didn't have as wide a dynamic range and nor does my current Dino Binci - it can't quite whisper, but then it can't half shout.  A friend's identical Binci doesn't have the same responsiveness, but it hasn't yet been fettled.

All the above basically supports the argument that whilst differing materials and "quality" may give different tones, but they can all be improved if the necessary time is spent on them.

Rob.
Logged

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Harmonikas Nastrino A Mano
« Reply #23 on: November 01, 2017, 07:32:04 AM »

If I understood the pictures correctly, it looks like two different bands of steel, the Professional cut across a wide band, and the Nastrino cut along a narrow band.  If that so, seems cutting across would waste more steel because of the different lengths, unless that's offset by the different widths in the Nastrino.

Firstly, just in case anybody gets confused by this, Harmonikas "Professional" are produced like high-grade tipo a mano reeds, but they're not a mano like Binci "Professional".

Secondly, wasting a bit of steel isn't any big deal - the advantage is getting all those rough-tuned reed tongues ground, and ready to slice off...

Yes we cant compare the way Binci is making reeds to the way Titelbach is producing reeds. Binci makes all him self and some Famely stuff now with old Machinery others did sell.  Other Factorys changed to new. Top quality a mano from Harmonikas are comparable if it comes to the tongue also Nastrino steel but the way the tongues are profiled with machines differ. Even the temperature may be different at the grinding process. Profile is made with a big grinding stone in the same direction. Machines differ. Shoes-Frames are made from the same Aluminium grade. But the way the are Made differ a lot. Bici files the slots with old machines to tapered, but precision is less. Titelbach uses elektro eroding slots are parallel. Reeds are fitted to the shoes by hand in both cases. But here it depend how well the final fit is done. First tuning is done different as well. BINC may use a final sanding with a hand operated belt sander as Ciccarelli does. Titelbach uses files to do the final pitch setting on the a mano nastrino. Best regards, Johann
PS: I fitted Titelbach a mano nastrino to one box and made a second set of reedblocks with Brass reeds from Ciccarelli. Tuned both the same way. So i have a second set to swish and make tests. I recorded and did some sonograms. Be aware the the difference is not as much as one would expect. Little difference in sound color as well.  Both reed sets are fantastic to me, most musicians who tested prefer one more as the other for different reasons but in average the is not the one best set. Test charts can be found on my Facebook page.
« Last Edit: November 01, 2017, 05:58:38 PM by JohannPascher »
Logged

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Harmonikas Nastrino A Mano
« Reply #24 on: November 01, 2017, 08:19:14 AM »

[], but the fit on both the A Mano Professional and the Dix reeds [is] very good, as far as reed to slot fit.  The dimensions of the Professional reeds (width and length) are close to the dimensions of the Binci a manos.  The Dix are smaller, very similar to the old German reeds they are reproductions of, and the sides of the reed tongues are parallel as opposed to tapered.  Response of both seem similar to me, but the professionals are much louder with a good punch. [tone is different] the professionals having a crisper sound.
This is  as i would describe it. Dimensions on Harmonikas professional nastrino reeds are taken from a sample Italian set made by Sabatini or Cagnoni not sure any more would need to ask again Ladislav Titelbach. So it is not surprise that the dimensions are nearly the same as other modern Italian sets.
« Last Edit: November 01, 2017, 05:55:54 PM by JohannPascher »
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Harmonikas Nastrino A Mano
« Reply #25 on: November 01, 2017, 02:29:18 PM »

This is a very interesting thread (to me anyway).  Thanks to all for sharing what you know !!   (:)
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Harmonikas Nastrino A Mano
« Reply #26 on: November 02, 2017, 12:28:11 PM »

Thanks for the report, Johann.  Speaking of trying all their reeds, have you also tried the A Mano Super I class, which apparently are stainless steel?  That is very appealing for some climates, but surely that affects sound and response(?), which may be a positive.

The A Mano professional's havea tone that appeals to me, and good volume, but initially seemed stiff in playing, as opposed to the super quick response of Italian a manos I've used (especially Ciccarelli, even when first installed), but after a couple days playing, there was a very noticeable improvement in response.  All in all, I really like them

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Harmonikas Nastrino A Mano
« Reply #27 on: November 02, 2017, 03:32:55 PM »

Thanks for the report, Johann.  Speaking of trying all their reeds, have you also tried the A Mano Super I class, which apparently are stainless steel?  That is very appealing for some climates, but surely that affects sound and response(?), which may be a positive.
Harmonikas A Mano Super I class are not with stainless steel tongues. This reeds are the same as the Nastrino but with the toungues not from Nastrino 8mm steel the tongue are made from 120 mm steel tape. Titelbach produces stainless steel tongues for mouth Harps and REEDS FOR MOUTH-KEY HARMONICAS so it would be possible to place special orders if one wants to. Never tried stainless steel tongues. I have testet other softer metals for single reeds to compare, so i conclude stainless steel would make also a little difference. Most of all it would effect the length of comparable pitched reeds if stiffens of the steel is different.   
« Last Edit: November 02, 2017, 03:47:00 PM by JohannPascher »
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Harmonikas Nastrino A Mano
« Reply #28 on: November 03, 2017, 11:37:29 PM »

Thanks for the report, Johann.  Speaking of trying all their reeds, have you also tried the A Mano Super I class, which apparently are stainless steel?  That is very appealing for some climates, but surely that affects sound and response(?), which may be a positive.
Harmonikas A Mano Super I class are not with stainless steel tongues. This reeds are the same as the Nastrino but with the toungues not from Nastrino 8mm steel the tongue are made from 120 mm steel tape. Titelbach produces stainless steel tongues for mouth Harps and REEDS FOR MOUTH-KEY HARMONICAS so it would be possible to place special orders if one wants to. Never tried stainless steel tongues. I have testet other softer metals for single reeds to compare, so i conclude stainless steel would make also a little difference. Most of all it would effect the length of comparable pitched reeds if stiffens of the steel is different.   

This from their website, under A Mano Super I Class description, "Tongues are made   from strip of stainless steel".  Is it not actually stainless steel?
« Last Edit: November 04, 2017, 01:40:51 AM by blafleur »
Logged

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Harmonikas Nastrino A Mano
« Reply #29 on: November 04, 2017, 07:22:48 AM »

Thanks for the report, Johann.  Speaking of trying all their reeds, have you also tried the A Mano Super I class, which apparently are stainless steel?  That is very appealing for some climates, but surely that affects sound and response(?), which may be a positive.
Harmonikas A Mano Super I class are not with stainless steel tongues. This reeds are the same as the Nastrino but with the toungues not from Nastrino 8mm steel the tongue are made from 120 mm steel tape. Titelbach produces stainless steel tongues for mouth Harps and REEDS FOR MOUTH-KEY HARMONICAS so it would be possible to place special orders if one wants to. Never tried stainless steel tongues. I have testet other softer metals for single reeds to compare, so i conclude stainless steel would make also a little difference. Most of all it would effect the length of comparable pitched reeds if stiffens of the steel is different.   

This from their website, under A Mano Super I Class description, "Tongues are made   from strip of stainless steel".  Is it not actually stainless steel?
Thanks for the report, Johann.  Speaking of trying all their reeds, have you also tried the A Mano Super I class, which apparently are stainless steel?  That is very appealing for some climates, but surely that affects sound and response(?), which may be a positive.
This from their website, under A Mano Super I Class description, "Tongues are made from strip of stainless steel".  Is it not actually stainless steel?
No definitely not i have been to Louny twice the last year, the last time just one month ago. I have seen the production again.  and i also did get Nastrino reeds and others. I had a longer talk with Ladislave on the subject as well. The have tree grads of a mano reeds for normal accordion sets. And A Mano Super I Class is the middle grade of a mano, with little bit less expensive tongues that is the only difference. Only difference between middle grade A Mano Super I Class reeds and normal a mano is that the frame a precision punched and not elektro eroded. Montage of the reeds all three types is done the same way by hand. Hand reverted. Surface of Frames are polished by machines. Tuned half by hand and machine, 5 cent accuracy. I did see a lot of employs beieng involved on the work in the final state of assembling and assembling. Machine for profiling tongues is a new one. Also the punch for lower grad reeds is very new and  operate from both sides.  So reed frame keep shape. And slots perfectly parallel without the need of a final filing inside the slots. So really the difference between the three grads is minimal. No other difference in tolerance or tuning methods or fitting.  Only the next lower grades differ, no hand riveting. less tolerance. and even on the very low grade cheaper Aluminium. Best regards, Johann

PS: English text on the webpage is with mistakes. i treed a google translation of the Czech text: "Voice plates are made of aluminum alloy. Steel with a hardness of 160 HB. Channels are cut by electro-erosive technology. The surface of the reed frame is cut. Reed frame sides are scored to create a better grip of the wax to the reed frame and the reed block. The tongs are made of Swedish steel with a tensile strength of 2000 N / mm2 with T3 tolerance, ground to an accuracy of -20 cents from the base tone, with a head width of 7 - 9 mm rivet, with corrosion protection. Reeds are riveted manually to achieve a perfect connection to the reed frame and precise centering of the tongue in the canal. The air gap between the channel wall and the tongue on each side is 0.03 mm and at the tip of the tongue 0.04 mm. The underside of the channel is extended over the top edge. A characteristic feature for the 1st class is the rivet head of the manual riveting to the multi side pyramid. The reeds are hand-tuned with the grinding paper, with the tongue's basic profile being adhered to +/- 5 cents.
« Last Edit: November 04, 2017, 07:50:25 AM by JohannPascher »
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Harmonikas Nastrino A Mano
« Reply #30 on: November 04, 2017, 10:44:21 AM »

PS: English text on the webpage is with mistakes. i treed a google translation of the Czech text: "Voice plates are made of aluminum alloy. Steel with a hardness of 160 HB. Channels are cut by electro-erosive technology. The surface of the reed frame is cut. Reed frame sides are scored to create a better grip of the wax to the reed frame and the reed block. The tongs are made of Swedish steel with a tensile strength of 2000 N / mm2 with T3 tolerance, ground to an accuracy of -20 cents from the base tone, with a head width of 7 - 9 mm rivet, with corrosion protection. Reeds are riveted manually to achieve a perfect connection to the reed frame and precise centering of the tongue in the canal. The air gap between the channel wall and the tongue on each side is 0.03 mm and at the tip of the tongue 0.04 mm. The underside of the channel is extended over the top edge. A characteristic feature for the 1st class is the rivet head of the manual riveting to the multi side pyramid. The reeds are hand-tuned with the grinding paper, with the tongue's basic profile being adhered to +/- 5 cents.

Interesting.  That's a big mistake.  So do you think the 3 classes of A Mano are all the same steel tongues?

JohannPascher

  • Good talker
  • **
  • Offline Offline
  • Posts: 55
Re: Harmonikas Nastrino A Mano
« Reply #31 on: November 05, 2017, 05:50:04 PM »

PS: English text on the webpage is with mistakes. i treed a google translation of the Czech text: "Voice plates are made of aluminum alloy. Steel with a hardness of 160 HB. Channels are cut by electro-erosive technology. The surface of the reed frame is cut. Reed frame sides are scored to create a better grip of the wax to the reed frame and the reed block. The tongs are made of Swedish steel with a tensile strength of 2000 N / mm2 with T3 tolerance, ground to an accuracy of -20 cents from the base tone, with a head width of 7 - 9 mm rivet, with corrosion protection. Reeds are riveted manually to achieve a perfect connection to the reed frame and precise centering of the tongue in the canal. The air gap between the channel wall and the tongue on each side is 0.03 mm and at the tip of the tongue 0.04 mm. The underside of the channel is extended over the top edge. A characteristic feature for the 1st class is the rivet head of the manual riveting to the multi side pyramid. The reeds are hand-tuned with the grinding paper, with the tongue's basic profile being adhered to +/- 5 cents.

Interesting.  That's a big mistake.  So do you think the 3 classes of A Mano are all the same steel tongues?
yes only the width of the steel tape that is use for making reed toungues is different for Nastrino. All are made from Swedish  steel with the hardness off 2000 N/mm2.
Logged
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal