Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4 5 6 7 8 9   Go Down

Author Topic: Recording king repair  (Read 31623 times)

0 Members and 1 Guest are viewing this topic.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #40 on: December 10, 2017, 10:39:43 AM »

Yes Equal Temperament is most likely.  If you suspect that it might be a different temperament you should look for consistent deviations from the target pitch on the same notes on all octaves.   If it's not ET the next most likely is Quarter Comma Meantone.   That is usually obvious because the thirds will be approximately 15 cents flat compared with ET, and the should apply across all octaves.  A handy app for trying to establish which temperament is a free app called RTTTA Tuner.   It allows you to record all the pitches over several octaves, displaying the deviations of each.    Then you can select from a variety of temperaments to see which appears to minimise the offsets.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #41 on: December 10, 2017, 12:54:35 PM »

Ok thanks Rob and Theo
I'll try that.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Recording king repair
« Reply #42 on: December 10, 2017, 12:56:32 PM »

Hi Theo and boxcall,

My best advice for boxcall is to to tune this accordion (maybe his first such attempt?) to equal temperament, A 440. Then he'll have the substantial challenge of achieving his target pitches but will only have to worry about 12 of them (multiplied by the pitch differentials needed to get his chosen tremelo).

The original tuning of this accordion, like other 1930s Hohner 3-rows I've studied, is actually likely to have been more complex, and included different target pitches for some notes that we might think of as "duplicates" as shown on a typical layout diagram.  IMO it's too far out of the mainstream of most player's understanding of how to play music, particularly if they are mostly teaching themselves and involving written resources such as the internet, to work with complexities of the original tuning of these instruments.

At some point I hope I'll have time and resources to share some of my unpublished ideas on tuning of free-reed instruments. But it takes a lot of explaining so would be best presented in a book or long article, to be read probably by a tiny minority of people who 1) are interested in this level of detail and 2) have already learned more basic music theory.

However, as I've often written before, I don't think that 1/4 meantone was commonly if ever used for Hohner accordions like this. The fifth intervals of 1/4 comma meantone are unnecessarily narrow. Many of these accordions were designed with at least some sweet major thirds, which is also true of 1/4 comma meantone, but not with those narrow fifths.  Some of these accordions don't have just (untempered) major thirds, but sweeter thirds than equal temperament. And there are other ways to optimize both thirds and fifths, including adding additional pitches (more than 12 to the octave); these become very complex to explain and to use with perfect understanding, but in fact they weren't hard to implement by folk players who picked up the instrument and played "what sounded good!"

In the past 20 years, especially in England, I think there has been a tendency to jump to an assumption that a particular historical  instrument's tuning is 1/4 meantone just because the thirds are pure, (or sometimes to the assumption that its tuning is "just," if only one diatonic key is available), when in fact much more complex tuning systems with more than 12 pitches to the octave have been in common use throughout the evolution of European free-reeds, especially with instruments that have multiple key centers plus accidentals (such as german and anglo concertinas, and 2- or 3- row diatonic button accordions / melodeons).

Again, boxcall - go for A 440 ET this time. It's the baseline that's been used by many of us to understand music theory over the past 50 years or more,  it will be a great learning process for you to achieve that tuning, and if you later decide that you want some specific different tuning, having experience tuning ET and playing / listening to the result will be very helpful when you go forward.

Best,

PG


« Last Edit: December 10, 2017, 03:41:07 PM by pgroff »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #43 on: December 10, 2017, 04:19:47 PM »

Thank you Paul for a knowledgeable and sympathetic answer!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Recording king repair
« Reply #44 on: December 10, 2017, 04:50:31 PM »

When I dropped in to visit Jolly Roger, he showed me a book of tuning schemes which basically covers the variations of tremolo across the range as typically used by individual manufacturers.  Some seem to like the tremolo beat frequency to increase with pitch, a few like it to remain constant throughout.  I'm sure others will come along with details and recommendations.  Any work you do in preparation will pay off at the tuning stage.  I would recommend mapping the frequency of each reed in the box before you start.  I have done this by cutting strips of paper and inserting them under the reed blocks to blank them off whilst I map another voice.  Once you get to the tuning table, map them again before doing anything else and you have a record of the offset to be expected when fitting them back into the box.  Apply the offset to the required finished pitch of each reed and the work should produce much better tuning when you put them back in....

The book I showed Rob was the Benetoux book on tuning. It has sample 'profiles'.  I know it's not very popular on here...but I personally find Dirk's Tuner invaluable, because it can read up to three voices at once, and give readings on the BPS and or cent offset. So it saves me a lot of time when diagnosing tuning issues, esp on honking great PAs that weigh as much as a small car and that have reed blocks as long as your arm. And very often you get different readings with the blocks out of the box and on the tuning table, esp when they are working together, than when they are in situ. So I usually fine tune with all the reed blocks in situ and use Dirks to get a handle on (say) which of the two MM reeds I need to tweak, and in which direction. On the tuning table I use Petersons or my rather quaint Korg Orchestral, with a needle that bounces back and forth.

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Recording king repair
« Reply #45 on: December 10, 2017, 04:55:48 PM »

Thank you Paul for a knowledgeable and sympathetic answer!


Hi Theo,

No, thank you! For all you do (hands on and in community building here). I mean, I think you are the one who's being sympathetic, in understanding my answer above, which could just as well be read as arrogant and obscurantist (though I hope that would be a misreading of my answer).   

I think you understand my ongoing work on this. I'm continuing my efforts to draw attention of those who have a genuine curiosity about tunings,  to a fine point ( 1/4 comma vs other non-ET tunings and temperaments) but not get bogged down in a really long (book length) explanation in this forum context.

Boxcall's RK has been reworked so it wouldn't make sense to "trust all the notes that seem out of tune," in his accordion.

But Theo, you probably have encountered boxes that have their original reedwork intact - but may have some notes that could be "misinterpreted" as out-of-tune, but were intended to be at those pitches, in a fairly complex arrangement including duplicate examples of a nominal note (such as "E" for example) that were intentionally tuned to different pitches for different harmonic uses. That's where there is a chance to listen and learn from the instrument, rather than assuming its tuning must conform to some simpler, well-publicized system like "1/4 comma with 12 tones to the octave" (or even with more tones).

This business of determining and restoring original tunings can take a lot of time and not be appreciated in the end by 99% of today's players who are approaching the instrument differently than many of the pre-WW2 players. But I do feel obligated to mention this alternative perspective when the subject comes up as with boxcall's question.

Again, my recommendation to him in particular for his particular project with this particular box in its particular present condition is to tune it to A 440 ET. If he achieves this he can be really proud; then maybe a different project will beckon.

PG
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #46 on: December 10, 2017, 05:51:30 PM »

Paul,  I’m still looking forward to reading your book/monograph/paper or whatever form you eventually publish. 

I’m assuming that push pull instruments give some extra opportunities for designing temperaments that exploit the feature of the instrument that many notes are duplicated on different bellows directions, and that not all notes are available on any one bellows direction.  So the duplication is an opportunity to have two different versions of one note that harmonise well with other notes on that bellows direction without having to consider clashes with the notes that only exist on the other direction.  I’ve never got far with thinking that through because I lack the tools (mathematical and imaginative) to take it forward.

I take every opportunity to preserve old tunings and that is appreciated by a small number of customers, but it can be hard to get over the misconception that departures from ET are out of tune.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Recording king repair
« Reply #47 on: December 10, 2017, 06:03:51 PM »

Hi Theo,

Yes, exactly. And it's one of those things that is much easier to just play, than to "figure out" -- if you have an "ear based" approach to a kind of music that works within simple scales and modes. A lot of today's amateur players don't have that ear-based approach, and also the process of playing new kinds of styles may not overlay well on the old tunings (for example if you assume that you can play every interval in both bellows directions; some tunings may not favor this, even if the notes as named are present in both bellows directions). But some of the 19th century makers and tuners, and some of the better musicians, who came up with some of the note layouts, and the tunings for concertinas and diatonic accordions / melodeons, were very clever, and often paid more respect to beautifully harmonious intervals than does much music made after WW2.

Also, there's another factor that may contribute to a tendency of modern players to consider "intended original tuning of non-ET free reeds" as "out-of-tune." Some of the original intervals used in some concertinas and accordions were just plain sour, and I myself have a hard time enjoying them.

This is especially true of the interval between the 4th note (fa) and the 6th note (lah) of a scale, played together on the draw, of many old free reeds. For example, the notes F and A on a C row.  That fa-lah interval is a major third, but on many old original instruments it's tuned very wide of equal tempered thirds. And ET thirds are already far wide of just thirds. You can hear that sour interval in the Wyper's recordings even though their instruments were fully chromatic, and you can hear it on the cheap 2 row German Concertinas made up through the 1960s or later. Those have great major triads on the press but two very sour major thirds on the draw. I suspect that the tendency of some cajun accordion makers to tune up the F note sharp of concert pitch (on a C 1-row accordion) may have begun with a request to ameliorate those "traditional" German F notes that arrived tuned (intentionally by the maker) to a note so flat that the F-A interval was sourer than ET. Of course, if you take the F sharp enough relative to the A, you can arrive at a F-A interval that's sweeter than ET.

PG
« Last Edit: December 10, 2017, 06:18:24 PM by pgroff »
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #48 on: December 10, 2017, 09:10:03 PM »

Hi Theo and boxcall,

My best advice for boxcall is to to tune this accordion (maybe his first such attempt?) to equal temperament, A 440. Then he'll have the substantial challenge of achieving his target pitches but will only have to worry about 12 of them (multiplied by the pitch differentials needed to get his chosen tremelo).



Best,

PG




Thanks Paul and all,
Yes this is a first time attempting to tune a box , but it was free and with a hodgepodge of reeds why not try. I will go for ET as you suggest. I'm assuming I can tune the block (one bank of reeds) in each key that is closest to actual pitch to A = 440 and exactly to pitch all the way up the scale. And do the other with the tremolo X amount of cents above pitch A at say 448. But how do you figure the rest of that bank of reeds? I think more is need on the lower reeds and less on the higher, is there a formula or is this where you have to just use your ear.
Do tuners do treble side first then bass side or other way around?

I've got a lot to learn!!

Just to clarify the readings on the tuner that I was taking was on my Beltuna, using the stops to close off the other banks. I was getting a lot of readings that where several cents sharp on the banks that should be right on or close ( some notes were ok). I was doing this just to get an idea on how the tuner worked, apparently I need to get a tuning on that box.
Maybe I should ask should these notes read right on? Or is there a little room +- a couple cents.
One bank M+ was about 10 to 15 cents but varied.

Michael
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #49 on: December 10, 2017, 09:23:40 PM »

If you want a constant beat rate then the difference between M+ and M should halve with every octave you go higher and double with every octave you go lower.  That is the theory. In practice very few instruments are tuned like that.  It’s more common for the best rate to increase as you go up the scale.  If you tune a constant offset then the beat rate doubles every octave you go higher. 
Most accordions (diatonic or chromatic) are tuned somewhere in between. My take is that the ear is the best way to get the beat rate you prefer. 

The tolerance you tune can vary with the degree of tremolo you use. +/- 1 or even 2 cents might be ok for a very wet tuning,  but for swing tuning where the offset might only 4 cents then even +/- 1 cent is too much because taking the worst cases the tolerance might be M + 1 and M- -1 so the offset is halved. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #50 on: December 10, 2017, 11:16:45 PM »

Thanks Theo,
Sound advise as always!! Pun intended.
I think I'm following you, It's going to take a little trial and error -- I think.
I just spent a little time cleaning some reeds and trying to figure out what is what M or M+ Reeds on the C row there all over the place but I think I'm finding the bank that's closer to M.
I also have been learning the fine art of gentle persuasion, as some reeds are not speaking so I'm adjusting the gap. A couple have needed a little moment to one side as they were dragging on the side of channel (only the tip was moving), amazing how they come to life when you get it just right.
So far so good at getting them to at least speak properly, next comes the hard part of getting them to speak the right language.
I don't know how you tuners do it? My neck is killing me!! After one bank of reeds.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #51 on: December 11, 2017, 08:48:24 AM »

You seem to be getting on very well and learning fast!  When working out which is M and which is M+ don’t neglect the possibility that some reeds may have ended up in the wrong place.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Recording king repair
« Reply #52 on: December 11, 2017, 10:12:11 AM »

I don't know how you tuners do it? My neck is killing me!! After one bank of reeds.
I am prone to neck and shoulder problems when tuning. I have to be very careful.
The best solutions are (i) have your bench and working area set up at a proper height. The worst thing you can do is be standing up with your neck bent over the work. I've found that an adjustable office chair and a relatively high tuning bench is best for me, so that I am looking more horizontally at what I'm doing, rather than peering down. Then (ii) have good lighting and magnifying specs if you need them (I like to have them) so that you are not straining to see exactly what you are doing.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #53 on: December 11, 2017, 10:36:05 PM »

You seem to be getting on very well and learning fast!  When working out which is M and which is M+ don’t neglect the possibility that some reeds may have ended up in the wrong place.
Thanks Theo, I couldn't do this without out your help and the help of this forum!!

I do have to be aware of reeds in the wrong spot as there were a few floating about inside when I got it. I think I got them back in the right order but time will tell. 

What's puzzling me is when I was checking the F row ( I started with this row) I was getting The same pitch on the push and pull ( this is the row that had the newer looking reeds, aluminum plates) I'm not sure what's going on with this row yet. I may need to see if some reeds where taken from the piano box I got? When I moved to the C row ( older reeds) things seemed more normal or what would be expected. I'll be looking at the G row tonight or tomorrow and report back.

I asked about cleaning the reeds earlier, is there a solution for this or just scrape off wax and glue?
Any one tried heating with heat gun then wiping off old wax( most of this is just on the edges)?
This could be a dumb idea and or messy. I've been scraping with small screwdriver and or razor blade and brushing the remaining bits.
How much do you really need to get off or how clean should they be?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #54 on: December 11, 2017, 11:14:08 PM »

The third row might have been altered to have accidentals and reversals rather than an F row, or there could be a gleichton which would be C both ways rather than C/D.

Old wax andvalve glue usually comes off pretty easily by scraping with a blunt knife.  I have an old kitchen paring knife with a broken off blade with the end ground at 90 degrees that I find perfect for this job. A wire brush is good too.  When brushing along the reed only brush from rivet to tip to avoid getting strands of wire stuck under the reed.
Heat is usually unhelpful because you just end up with a stick mess.  I have experimented with an ultrasonic cleaning bath.  In theory it is excellent, but it’s not good at removing  thick deposits so you still have to do a lot of scraping and brushing.  The surfaces do come out beautifully clean, but the steel tongues are so clean that they can start to rust very quickly, so the reeds need to be warmed to dry them, and then given an ant corrosion treatment.  It’s a lot of extra work for no great advantage.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Recording king repair
« Reply #55 on: December 11, 2017, 11:58:03 PM »

I asked about cleaning the reeds earlier, is there a solution for this or just scrape off wax and glue?
Scraping off old wax and glue with a blunt knife is good for the odd few reed plates, but if I'm doing a complete refurbishment, I'll rip off all the old valves and then use acetone to remove old wax and glue. I use an old plastic food container, the sort that takeaways come in, and lay a few reed plates flat in the bottom, then pour in sufficient acetone to just cover the reed plates. Gently swirl around for a minute or so and then use an old toothbrush to clean off the remaining gunk - what hasn't already gone into solution comes off easily.

Needless to say, you should work in a well ventilated area and away from any source of flame. Definitely no smoking!
I use industrial grade acetone, which is cheap as chips.

Waste disposal: I pour off any remaining acetone/wax solution into a glass bottle with a screw top, which then gets stored in my garage until I'm ready to have a bonfire of garden rubbish. It's great as a starter-upper!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #56 on: December 12, 2017, 12:00:53 AM »

Yes I was thinking along those lines too Theo , that maybe someone was playing as a GC with accidentals. ( maybe gleichton as you say) But I'll need to do a little more to verify that.
I'll keep scraping then, I was using the small screwdriver on edge so probably similar to your broken knife.
I might see if I can find a small wire brush, the ones I own would rip my fingers apart ( to big and stiff I think)

I don't know how you tuners do it? My neck is killing me!! After one bank of reeds.
The worst thing you can do is be standing up with your neck bent over the work.
It's like you were there, This is exactly what I was doing.
I'll have to reposition My work space,I think.
I get the same pain when doing overhead work on the construction site eg. Sheetrock ceilings, painting ceilings etc. problem is there no other way to do it.

thanks
BC
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #57 on: December 12, 2017, 12:10:48 AM »

I asked about cleaning the reeds earlier, is there a solution for this or just scrape off wax and glue?
Scraping off old wax and glue with a blunt knife is good for the odd few reed plates, but if I'm doing a complete refurbishment, I'll rip off all the old valves and then use acetone to remove old wax and glue. I use an old plastic food container, the sort that takeaways come in, and lay a few reed plates flat in the bottom, then pour in sufficient acetone to just cover the reed plates. Gently swirl around for a minute or so and then use an old toothbrush to clean off the remaining gunk - what hasn't already gone into solution comes off easily.

Needless to say, you should work in a well ventilated area and away from any source of flame. Definitely no smoking!
I use industrial grade acetone, which is cheap as chips.

Waste disposal: I pour off any remaining acetone/wax solution into a glass bottle with a screw top, which then gets stored in my garage until I'm ready to have a bonfire of garden rubbish. It's great as a starter-upper!
That might be worth a try Steve, thanks.
I know acetone is very flammable, a lot of fires start with wood floor refinishers cleaning the floor in preparation for the finish. I like tack cloth it's safer.

I often put paint thinners in jars let them sit in shed ( particles settle) then pour off the top and reuse a few times. I suppose this could be done with acetone if the next job did not have to be completely pure.
You could even run the stuff though a strainer.

Thanks for the tip!!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #58 on: December 12, 2017, 06:37:07 PM »

So In this video, of  Diatonix tuning reeds.
https://m.youtube.com/watch?v=PJdU8l4foRA
He is using a jig to pretune and the reeds that do not have valves, so does the shape of the jig keep the other reed from sounding or distorting the sound?
From what I read the sound changes when you apply the reed valve, true?

It appears that it's just big enough at the top but wider at the bottom, I'm wondering why it's wider at the bottom wouldn't a simple slot also work, or not?

This is a good idea, I should make a few sizes up. Quicker than what I'm doing now.
Probably just wraps them in chamois.

I be working on the G row today.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Recording king repair
« Reply #59 on: December 12, 2017, 07:24:42 PM »

So In this video, of  Diatonix tuning reeds.
...
It appears that it's just big enough at the top but wider at the bottom, I'm wondering why it's wider at the bottom wouldn't a simple slot also work, or not?

I make it wider at the top - probably to clear the other rivet?

PS need to clear the other rivet and top of the reed. The bottom of the other reed can sit inside the slot. I made up something similar and it seems very promising but not really played with it yet.
« Last Edit: December 12, 2017, 07:28:05 PM by malcolmbebb »
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: 1 2 [3] 4 5 6 7 8 9   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal