Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 ... 3 4 5 6 7 [8] 9   Go Down

Author Topic: Recording king repair  (Read 31516 times)

0 Members and 1 Guest are viewing this topic.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #140 on: January 28, 2018, 10:09:55 PM »

I got the bass reeds sorted today (working and in tune now), I will put them back in the box and fine tune.

I put the chord reed block back and was testing them (not to bad for tuning) only to find out that I installed them end for end so the top chords were at the bottom.  ::)  I'm not sure how that happened but it did.

Two steps forward three steps back.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #141 on: January 28, 2018, 10:57:01 PM »

I put the chord reed block back and was testing them (not to bad for tuning) only to find out that I installed them end for end so the top chords were at the bottom.  ::) 

Done that, several times. With chord blocks it’s not usually obvious at a balance which end is which.  I’ll often put a strip of masking tape along the top of the block and writing the note names on there.  I also start by just racking the reeds in place with couple of spots of wax on each reed plate, than put the blocks into the instrument and play through all the buttons, treble and bass.  Makes correcting any errors much quicker than having to dig reeds out of a full layer of wax.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #142 on: January 28, 2018, 11:28:13 PM »

Well that's a relief to hear, I did have all the notes written down on the block as I did my pretuning and all the reeds were in the right order. I must have spun the block when I went to wax them in. In hindsight I probably should have written on the reed itself what note was what. I think I got it now but I might do as you suggest and tack them with a bit of wax and recheck.
I guess if I wasn't making mistakes I wouldn't be learning or at least I'll remember it better (:)

On the up side the bellows feel really tight, I had some small holes in the leather diamond area which I patched from the inside. So even with a couple of screw holes that still need to be filled it's pretty good. I also replaced the bellow gasket which must of helped.

I'm assuming that it would be ok to reuse the wax that I removed from the blocks? It looks clean enough.

Edit to fix spelling
« Last Edit: January 29, 2018, 08:37:54 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #143 on: February 03, 2018, 06:55:47 PM »

The results are in ??
My first ever tuning results, I think I did ok for a rookie.

If you hear any thing bad, say it ......
I'm at about fifteen cents in the middle of keyboard M+ reeds.

I play though the B row then C row then G row scales , then a tune in G

I didn't play the all the chords/ basses  but they sound ok ( nice grunt) , although I just realized I have my C/F chord backwards. I'll need to go dig them out and flip them. It's tough on the tuning table as everything is in reverse, well that's my excuse ;)

I still need to do something with the air button, I think I see why they had a bar type, because as you move down the or up it becomes harder to use a button.

https://soundcloud.com/boxcall/recording-king-test
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #144 on: February 04, 2018, 09:17:19 PM »

I retuned a few notes as they sounded off.
I cleaned up the buttons as they were dirty / brownish (where it was mostly played), I tried cleaning solutions with no luck then rubbed it with a magic eraser which worked pretty good.
I was also trying to clean the grill with metal polish which didn't give very good results, so then I bought a little polishing wheel for the dremel tool, it had compound already in the wheel. I got really good results with it, it brought the shine back. The grill was very brown and I thought the finish was gone in some areas but with a little time invested it is now shiny (:)
I also sorted the bass reeds that I had reversed.

Next will be the air button......
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Recording king repair
« Reply #145 on: February 04, 2018, 11:26:34 PM »

Sounding very lively! Been following your thread here for quite a while now, and it's really nice to hear some sounds coming out of it.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #146 on: February 04, 2018, 11:59:08 PM »

Thanks Gena,
It does seem like I've been at this for awhile, and there's still more to do.
Considering that the reeds were loose and not really sounding ( buzzing or not moving) when I got it, I feel pretty good that it's somewhat playable now. It's been a fun project!! Fun that never ends I'm afraid  ;)

Thanks to all for your support with this, without it, I would not have got this far!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #147 on: February 06, 2018, 09:33:17 PM »

Here's what I ended up doing for the bass button, I filled in between the two holes that had been made prior with a bar type button similar to the one on my Baldoni. I still need to paint it black.

So another tuning question my M reed is tune spot on, M+ reed 15 cents in the middle. So then together in the box I'm getting readings of sharp 5 cents ( across the board) some a bit more so maybe I need to bring those down so everything is even?
So is slightly sharp normal? I guessing that it would have to be since I'm not doing M- M+.

When I use the hertz a few notes are spot on and the rest are high, my C row seems closer than my G row when it comes to getting the meter to come to a stop or slight movement.
Chord and basses are good two chords could use to come down a touch.

In the end is is hertz or cents equal or should I rely on one versus the other.

On my Baldoni the hertz is spot on, I didn't get to check cents on that one.

On my Beltuna not every reed is exactly on target (cents) for the LMH rows but when I check hertz it's right on the whole way.

I know the ear is best and I can sort of hear that some notes are off but I'm not sure I'd trust my ear,
I'm sure the more you do this the better your ear becomes.

Any further advice would be great, thanks!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Recording king repair
« Reply #148 on: February 07, 2018, 01:08:25 AM »

So another tuning question my M reed is tune spot on, M+ reed 15 cents in the middle. So then together in the box I'm getting readings of sharp 5 cents ( across the board) some a bit more so maybe I need to bring those down so everything is even?
So is slightly sharp normal? I guessing that it would have to be since I'm not doing M- M+.
Whether you use Hz or cents for your measurement units, the theoretical resulting pitch* which the ear perceives is the mean of the two reeds M and M+.

So if your M reeds are set to zero cents offset, and the M+ reed is tuned 15 cents sharp, the resulting perceived pitch of the two reeds sounding together will be 7.5 cents sharp. Some electronic tuners will respond to this mean pitch, others just get confused by the two reeds sounding together.

Similarly, if say, for the note A you have one reed tuned to 440 Hz and the other to 442 Hz, the resulting perceived pitch will be 441 Hz with a tremolo rate of 2 beats per second.

*In practice, I've found that this works so long as both reeds are responding equally well at the same loudness dynamic. If one reed is more dominant than the other, this can shift the perceived pitch slightly towards value of the dominant reed. So you need to ensure that the reed gaps are set properly so both reeds are responding at their optimum. Also, both sets of valves should be of the same material and be working properly, lifting by the same amount.

Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #149 on: February 08, 2018, 04:42:20 PM »

I'm a little perplexed, so I am trying to get the reeds tune better.
I blocked off the M+ row and took reading of each note in the box, made a chart and did the same for the other bank of reeds. Then working the M rows first I checked the readings on the tuning table and figured the offset between the two readings. Working the G row first it has low notes D/F# the D ends up being 4 cents sharp the F# 1.9 to 2 cents sharp, next notes G/A both end up 2.5 cents sharp, then next notes B/C  in the box readings of 1.3 / 3.0 sharp on the tuning table 0.00 / - 1.5 , so I would bring the B down to -1.3 and the C down to - 4.5 (if I'm doing the math right).

Is this normal to have notes several cents sharp then several cents flat?
I'm probably overthinking it but don't want to go though the process if it's wrong.

Also is the whole cents setting close enough or should I use the setting I'm on?


Edit to add: I know a couple of cents sharp is expected as Theo mention earlier, so the G/A notes being about right I would think
« Last Edit: February 08, 2018, 04:55:52 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #150 on: February 08, 2018, 05:04:15 PM »

then next notes B/C  in the box readings of 1.3 / 3.0 sharp on the tuning table 0.00 / - 1.5 , so I would bring the B down to -1.3 and the C down to - 4.5 (if I'm doing the math right).


Unusual to have the readings in the box higher than on the tuning table.  I find it is almost always the other way round.  Are the air vents in your tuning table at least as big as the vents in the base of the reed block?  And how thick is the plate on the top of the tuning table?   It should not be significantly thicker than the fondo.  And how much pressure are you applying on the tuning table?   Too much pressure will makes reeds sound flat.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #151 on: February 08, 2018, 06:03:22 PM »

Air vents are the same slightly larger , table thickness is 1/2" and I'm using even pressure not to hard I'm trying to simulate the in the box pressure and yes the more pressure applied does make it sound flat.

Edit I just checked a few more reeds and they do seem higher in the box, some less than others.

Is the after adjusting some being sharp some flat normal? To get results of on target in the box.
« Last Edit: February 08, 2018, 06:28:54 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #152 on: February 08, 2018, 07:21:34 PM »

Table thickness of 1/2" might be a problem.  Usually the fondo is more like 1/4 or even slightly less.  This can make a difference.   Do you have free open space under the table?  I made a tuning table once where I made a tunnel about 1" high so I could put the bellows well back from the work area to give me more knee room.  It had some very undesirable effects, the most obvious of which was that Bb reeds would not sound, though every other pitch was ok ish.

Usually I find that the pitch in the instrument is about 2 +/-2 cents flat compared with the pitch on the tuning table.   Thats just ballpark figure because I do all the final tuning with the reed blocks fitted inside the instrument, so I don't attempt to work out offsets to apply when the block is outside the instrument.
« Last Edit: February 08, 2018, 07:25:52 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #153 on: February 08, 2018, 08:21:24 PM »

Ok, so slight variation up or down is ok.

My tuning table looks similar to this one but mine has more room under the table top for the bellows so I can open and close them a bit farther than His.
https://m.youtube.com/watch?v=Bl8K8_TrI6c

I guess I could make a u shaped thing to wrap around the bellows on the box and try to get readings using the box itself. I think it would be awkward for me to try tuning in place. And putting the box together and taking apart for every reed doesn't make sense.

I thinking of the u shaped table I saw being used in one of the building classes.

What have I got myself into?? ;)
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #154 on: February 08, 2018, 09:40:33 PM »

Re: Recording king repair
Two problems with the tuning table in the video.

1 there is not nearly enough travel on the bellows, the reed won’t be sounded long enough for the pitch to stabilise.  My bellows have a travel of 200mm/8” and the bellows are bigger.

2 the top table thickness is a problem.  I think that even your 1/2” inch top could be lowering the pitch you are recording.

Tuning in the box is not as hard as you fear.  Here is the very simple fixture I use to employ the instrument’s own bellows.  The top of the instrument is just placed on top of the bellows, no pins in place.  So the end I’m working on can simply be lifted off and replaced.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #155 on: February 08, 2018, 10:38:47 PM »

Thanks Theo,
My tuning tables has more room than his because I thought that would be a problem, mine has about 8'" of travel and I'm using a full size PA bellows.
I didn't realize that the top should match the fondo thickness, I could probably router out the under side to make it thinner. I think I'll just make a jig like you posted and go that route.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Recording king repair
« Reply #156 on: February 08, 2018, 10:48:40 PM »

Interesting, I find that reeds on my table go sharp when fitted. And it has a thick top. A remedial plan is in hand.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #157 on: February 08, 2018, 11:33:54 PM »

So if I understand you Malcolm your reeds are doing what mine are doing? Becoming sharp when installed in the box. Maybe it is the top thickness then.

By the way Theo what is the thickness of your table top ?
I only went with 1/2" because I used a 1/4" slide to open and close off one or two holes, I also added a big hole to be able to do the bass and chord reeds, it gets blocked off when I move it to the other positions.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Recording king repair
« Reply #158 on: February 08, 2018, 11:56:27 PM »

Mine is 1/4” ply.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Recording king repair
« Reply #159 on: February 09, 2018, 12:44:53 AM »

Interesting that the thickness of the table makes a difference.
I guess that I could see that if the reeds are mounted under it like they are inside the box  but I did not think it would matter with the reeds being sounded on top of the table, so the sound isn't coming though the table. And all the air is getting throttled down to the same size hole but now passing though an extra 1/4" . I understand pressure difference between inside and out , there's quite a bit to think about.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: 1 ... 3 4 5 6 7 [8] 9   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal