Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 [3] 4 5 6   Go Down

Author Topic: Reed blocks ... come on then - how do you do it?  (Read 25511 times)

0 Members and 1 Guest are viewing this topic.

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: Reed blocks ... come on then - how do you do it?
« Reply #40 on: December 05, 2017, 07:44:06 PM »



I see you dado the chamber side pieces into the top (pretty deeply I might add) do you also dado into the bottom piece? What is the benefit to the dado ?  I asked this question above in a post.

Edit to add: I can't see how the taper is cut in the photo, can you explain?


It'd make more sense if I post a pic of my current cutting jig.  It's adjustable to angle and depth.  I'll see if I can post a pic.

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #41 on: December 05, 2017, 07:44:14 PM »

There is a hackspace in Oxford ... with a laser cutter, 3D printer etc.  I have been tempted!

https://oxhack.org
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #42 on: December 05, 2017, 09:01:15 PM »



I see you dado the chamber side pieces into the top (pretty deeply I might add) do you also dado into the bottom piece? What is the benefit to the dado ?  I asked this question above in a post.

Edit to add: I can't see how the taper is cut in the photo, can you explain?

It'd make more sense if I post a pic of my current cutting jig.  It's adjustable to angle and depth.  I'll see if I can post a pic.
That would be great, thanks !!


Laser cutting sounds good, is that still woodworking ? :P
I guess you could say that about any power tool.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #43 on: December 05, 2017, 09:23:06 PM »

Laser cutting sounds good, is that still woodworking ? :P
I guess you could say that about any power tool.

I was asking about making reedblocks ... by whichever method has worked for people.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Reed blocks ... come on then - how do you do it?
« Reply #44 on: December 05, 2017, 09:29:32 PM »

Actually, I neglected to mention the concept but a CNC machine/3D mill that is able to both deal with wood, and larger volumes of it, would probably be the more useful mating of technology and wood for a reed block - not all CNC machines are equal in what they can deal with. Laser cutting is usually restricted for thinner woods, which would probably be great for making the sides, keyboard facings, slides for voice registers etc, but usally leaves an unsightly blackened edge. A 3D printer is probably not that useful for a melodeon, although I do know that a harmonica player sells 3D printed combs (analogous to reed blocks) that have shaped internal structures behind each reed, to I guess enhance them in some way, although granted, I think he is selling them, so maybe take with a pinch of salt, but in much the same way, often there are angled wooden inserts placed in a melodeon's block to enhance response.

Regarding insurance, being that we as musicians do place a rather high value on not just the presence but the full functionality of our digits, I would heed boxcall's trepidations. It's unlikely that a large, well run space will not have insurance, but most likely this will not be insuring you and your wellbeing using a machine you shouldn't be, but rather the damage you might cause to other people and their property in that circumstance. I may have somewhat misrepresented things though, as generally these spaces started as being about helping the technologically savvy make real physical things with communally funded equipment, rather than leave the keys to a fully equipped industrial workshop under the welcome mat and sometimes there's a computer in there somewhere. They are about just sort of, making some stuff, even if that's googly eyes, felt and some precision cut aluminum.

The thing to think about it is that, fortunately, much like there is for morris sides, there is a lot of guidance about how to structure, run, insure and protect the interests of the people involved when running a space. That advice extends to things like, having rules about who can use certain tools (eg they attend an education event the space runs on it), if guests can even enter or make use of certain things etc. A lot of the need for the more dangerous tools is sidestepped at the design stage, being replaced by what the machines can do for you in a protected, plastic box, and even then education is often required for that particular make/model.

Veering back to the topic in hand, actually making a reed block. You seem to be invested in making a single piece comb, without using wax. (I think maybe you're kind of starting off on a harder difficulty!). Presumably that means you'll be using some kind of pressure (screws/bent nails) against eg a leather or felt facing applied to the block to make an air tight seal? Or, is it possible to secure the reeds directly against the wood? I would have thought that some material would be needed, and that an additional piece of wood may need to be placed running along the bottom edge of the comb after the cutting, to create the little boxes needed to secure both ends of your reeds against with just that one axis of pressure. Then again, perhaps if you can get it just so, maybe neither is needed? I'd be quite interested to hear your design ideas and what your plan is for this. I sort of made myself a reed block recently, but, I was happy to settle for 'works' - it was made out of hardboard and balsa wood and lives in a toy melodeon, and it does indeed work, but, I suspect your demands may be a little higher.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #45 on: December 05, 2017, 10:11:00 PM »

Laser cutting sounds good, is that still woodworking ? :P
I guess you could say that about any power tool.

I was asking about making reedblocks ... by whichever method has worked for people.
Sorry,  I know you were, I was just being stupid / funny.
Kicks self, (don't try to be funny it never works out!)
Laser cutting would be a valid way of doing it, no doubt.
« Last Edit: December 05, 2017, 10:13:12 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #46 on: December 05, 2017, 10:43:19 PM »

Or, is it possible to secure the reeds directly against the wood? I would have thought that some material would be needed, and that an additional piece of wood may need to be placed running along the bottom edge of the comb after the cutting, to create the little boxes needed to secure both ends of your reeds against with just that one axis of pressure. Then again, perhaps if you can get it just so, maybe neither is needed? I'd be quite interested to hear your design ideas and what your plan is for this. I sort of made myself a reed block recently, but, I was happy to settle for 'works' - it was made out of hardboard and balsa wood and lives in a toy melodeon, and it does indeed work, but, I suspect your demands may be a little higher.

The reason I'm trying to cut a comb from a solid piece of wood is mainly because I have a hunch it can affect the sound of the reedblock in a positive way (with no proof except from circumstancial evidence built up over years of listening to boxes) - with my current setup here, it also seems like a quicker way to build a reedblock than by buildiing a jig to space out the parts and then assembling like a model aeroplane.

Aiming for waxless is due to a personal gripe against the messyness of wax for a box which needs ongoing maintenance - I certainly know that waxless boxes can sound every bit as good as their waxed counterparts and I just prefer them!  You're right that you need a gasket material with some give in it on top of the block to press the reed in to.  The traditional material is leather or olivisc (like a thin cork) ... I was also going to experiment with Sugruâ„¢ (google it if you don't know what it is ... it's amazing stuff).

The way I envisaged fixing the reeds in a waxless way was to create a lip on the end of the reedblock (nearest the fondo) which could wedge the top end of the reed plate and then have every reed plate screwed in place using a screw and washer or a cam of some sort at the other end to press the plate in to the gasket material.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #47 on: December 05, 2017, 10:45:48 PM »

Sorry,  I know you were, I was just being stupid / funny.
Kicks self, (don't try to be funny it never works out!)
Laser cutting would be a valid way of doing it, no doubt.

Well - I can see how it would be hard to cut wood thick enough for reedblocks using laser cutting ... but this fantastic little video shows how it may be possible.  I don't know how this would affect the sound though.

https://www.youtube.com/watch?v=6qAaNlVZHnw
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Reed blocks ... come on then - how do you do it?
« Reply #48 on: December 05, 2017, 10:49:04 PM »

I'm sure someone here started building a beautiful box with milled aluminium reed blocks, and I think the reed plates were held on with screws and o rings.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Reed blocks ... come on then - how do you do it?
« Reply #49 on: December 05, 2017, 11:04:26 PM »

The reason I'm trying to cut a comb from a solid piece of wood....

There was a series on TG4 in Ireland about instrument makers (Ceird an Cheoil) and the accordion episode featured mainly Martin Connolly of Kincora accordions. He was shown cutting a comb from a solid piece of wood using a table saw. I swear the whole program was on YouTube at one point but I can't find it just now. Perhaps some more diligent searching than I have time for just now will turn it up.

It was discussed in this topic but of course the TG4 player link given there won't work at this distance in time. http://forum.melodeon.net/index.php?topic=8660.0

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Reed blocks ... come on then - how do you do it?
« Reply #50 on: December 05, 2017, 11:55:04 PM »

Cutting slots with a table saw is pretty easy, if you haven't got the obstructive over-the-top blade guard. Each pass cuts the width of the blade, you make repeated cuts to the width you want.
Suitable care of fingers and eyes and preferably some decent dust extraction or a mask taken as read.
I've made a sled for mine, loads of designs on Youtube, supports the workpiece very well and helps keep fingers and blade separate.

But a hand saw and chisel will work :)

I had an old scrap PA reed block with the bark still on at one end.  :||:

Didn't know Gena had joined the Chanson club  ;D
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #51 on: December 05, 2017, 11:56:49 PM »

I think myself ( speaking for myself) and others (judging from what others have posted) are thinking of the more traditional way of making reed blocks. I must have missed that you are trying to make it out of solid piece of wood.
That is a difficult and would lead to having the grain in the wrong direction, which ever way you run it. and this could lead to failure?  Even if you could cut this on a laser cutter.
As you know from the video you posted He's using plywood and gluing sets together for strenght.

I guess you could cut from solid wood but which way do you run the grain? what kind of wood are you going to use?

I suppose you could cut this with a router and a templet, taking small passes until you get though the thickness of material then squaring the corners, or cut with table saw and a dado blade and a little hand work at the top.

I see now table saw has been suggested in Stiamh's post I think that would be the easy way but you still have a grain problem
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #52 on: December 06, 2017, 12:06:00 AM »

Cutting slots with a table saw is pretty easy, if you haven't got the obstructive over-the-top blade guard. Each pass cuts the width of the blade, you make repeated cuts to the width you want.
Suitable care of fingers and eyes and preferably some decent dust extraction or a mask taken as read.
I've made a sled for mine, loads of designs on Youtube, supports the workpiece very well and helps keep fingers and blade separate.

But a hand saw and chisel will work :)

I had an old scrap PA reed block with the bark still on at one end.  :||:

Didn't know Gena had joined the Chanson club  ;D
add a dado blade to table saw and you won't need as many passes.
also a tenoning jig could be use to hold things or the cross cut guide with a piece of wood screw to it ,extending the lenght of guide out over the blade. this also helps with lining up the cut.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Reed blocks ... come on then - how do you do it?
« Reply #53 on: December 06, 2017, 12:07:34 AM »

Aiming for waxless is due to a personal gripe against the messyness of wax for a box which needs ongoing maintenance - I certainly know that waxless boxes can sound every bit as good as their waxed counterparts and I just prefer them!  You're right that you need a gasket material with some give in it on top of the block to press the reed in to.  The traditional material is leather or olivisc (like a thin cork) ... I was also going to experiment with Sugruâ„¢ (google it if you don't know what it is ... it's amazing stuff).

Yeah, what you're saying about the solid comb makes sense to me. I just sort of eyed up where they might need to be and sort of, splodged slats in with some glue (which was good because the holes in the fondo and the position of the reeds didn't line up very well) - I can see that in a less silly situation, following a precisely spaced printed out template from a computer makes a lot of sense, and lets you make use of any straight edges your material already has and is really quite a lot less fiddly.

Using Sugru for the gasket sounds super interesting! I'm familiar with it and have some probably within an arms reach, for my husband's ongoing effort to secure a magnetic USB charger header to his smart watch and maintain the water resistance rating, but, haven't actually used any of it yet. I imagine that it would probably do the job, and work great to 'hide the crimes' of anything that goes wrong on the way to making your block, in terms of filling any spaces that need being filled (in the same way I may or may not have used some wax...). When in the process of the sugru setting do you think you'll be putting the reeds on? Obviously there's likely to be some experimentation required, but, it seems like it might be hard to get it 'flat' without attaching them at some point before it sets.

Waxless sounds like a great idea to me though, especially from the mucking around at home perspective. I'm uncertain of the mechanics of the lip but it sounds like you have an idea for it. I looked back earlier in the thread to see how they were secured in the melodeon maker's course, going through the links Steve Freereeder posted - this image specifically implies to me that results can be achieved with even just a single bolt between each plate. I mean, that makes sense when you remember they're a rigid metal plate, although one suspects that ensuring the screws go in nice and level is key (perhaps perpendicular pilot holes are made for them first?). If putting the bolt between them is unfeasible due to the spacing, or if top and bottom seems like a better option, some kind of lip does seem like it would be effective as a way to deal with it. My worry is that it might be hard to have the lip apply enough pressure to the reed + gasket, but also being able to get the reed in in the first place. A picture would probably be worth a thousand words here though!

Either way I can see what you're doing as making sense and probably what I would do with the equipment you have - whether that's a good thing or not I'm uncertain, but, probably quite untraditional. I suppose also you get to decide which way your comb goes, if you're sticking on a top, or, sticking on a back - I've been assuming the back this whole time. One of the reasons I guess that you wouldn't want to do this method en masse is that, the 3 the surfaces inside each reed cell of your comb would have to be finished in some way in order for them to be consistent and smooth. Putting it together like a jigsaw puzzle, you can use planed & lovely, pre-smoothed and cut slats between each one, with likely a favourable grain direction for each side wall - transferring almost all the work away to something a machine can do easily. (Just saw boxcall posted about the grains while I was writing this! Glad I'm not imagining that as a potential issue!)
« Last Edit: December 06, 2017, 12:09:18 AM by Gena Crisman »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed blocks ... come on then - how do you do it?
« Reply #54 on: December 06, 2017, 12:32:21 AM »

....ensuring the screws go in nice and level is key (perhaps perpendicular pilot holes are made for them first?). ...
Yes - perpendicular pilot holes were drilled first.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Reed blocks ... come on then - how do you do it?
« Reply #55 on: December 06, 2017, 01:28:01 AM »

I've not actually explored ovidisc substitute, except that thin self adhesive gasket material might work, like this...which is something I've thought about...
https://www.clasohlson.com/uk/Assorted-Gasket-Material/30-8419?gclid=CjwKCAiApJnRBRBlEiwAPTgmxMInInkAr2_CpuZjkFr22fUQMLc64cHWwbKZ9KrrZRo-0ZByr6iB4hoCN5IQAvD_BwE

However, I've seen a few old 1930s Hohners that use leather, which would be my choice. The reed chambers do need to be precisely the right size, whereas wax does covers cracks and poorly fitting reeds. Also, for screw-on plates you need to get your hands on the tiny little screws.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Reed blocks ... come on then - how do you do it?
« Reply #56 on: December 06, 2017, 07:24:31 AM »

Sugru is a form of silicone rubber that may rolled and moulded, then sets when exposed to air. It has a fairly short shelf life. It's fun to use. I have only used it where I wanted a permanent fix, not sure how  easy it would be to remove and replace when necessary.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #57 on: December 06, 2017, 10:59:51 AM »

Boxcall ... I think you hit the nail on the head when you talk about the grain running in the wrong direction especially with respect to this particular project which has very thin dividing sections between the reed chambers.  Apart from the struggle to cut accurate straight lines (user error), the failings have been when the wood has split with the grain at these weak points.  Of course, once the wood is assembled and glued together in the reedblock, the whole thing is very much reinforced and I can't see it failing once in use.

Sugru is just an idea I had that may or may not work.  It is indeed a mouldable sillicone rubber which comes in little foil sachets (that have a use by date) it works like plasticine for the first hour or so after opening and cures in 24 hours to a solid but flexible and compressable rubber - in curing it also sticks like glue to most surfaces, but not to cling-film which can be used as a barrier if you wish to remove it with the option to glue it on later.  In my experience of using it - it can be removed with a bit of effort once bonded if you need to.  I don't know exactly how long it would last in a melodeon but sillicone rubber is a long-lasting material.  More of a concern to me would be that having a more "bouncy" gasket than is traditional might take some of the power out of the reeds by introducing flexibility in to the system, however I am anticipating screwing them down hard.

I imagined working the sugru in to thin sausages, lining them up on the areas around the reed chambers and then using a cling-film wrapped piece of flat wood to clamp/vice to the reedblock to squash it down to the desired thickness.  Then I was going to trim off the excess and clean up the chamber edges.  I wasn't planning on placing the reed plates at this stage to create moulds for them once cured although this could be a good idea.

Here's a picture of the block from sketchup showing what the lip looks like
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed blocks ... come on then - how do you do it?
« Reply #58 on: December 06, 2017, 12:26:26 PM »

I cannot help but wonder if a gasketless joint would not be preferable?
Although I haven't worked with wood all that much, I do know that high performance engines often don't use cylinder head gaskets, relying on good surface preparation and clamping instead. As I'm confident that compression in such engines exceeds that in a melodeon buy many times, why couldn't it be done? (On second thoughts, there's no gasket involved in waxing reeds, is there? But I suppose that the clamping effect would be lacking in comparison to screwing.) I feel that using a gasket must deaden the sound, although I couldn't explain how.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #59 on: December 06, 2017, 01:10:24 PM »

I cannot help but wonder if a gasketless joint would not be preferable?
Although I haven't worked with wood all that much, I do know that high performance engines often don't use cylinder head gaskets, relying on good surface preparation and clamping instead. As I'm confident that compression in such engines exceeds that in a melodeon buy many times, why couldn't it be done? (On second thoughts, there's no gasket involved in waxing reeds, is there? But I suppose that the clamping effect would be lacking in comparison to screwing.) I feel that using a gasket must deaden the sound, although I couldn't explain how.

When it comes down to reed-blocks and how different parts of their construction affects the tone of the reed in the instrument then I have yet to see any conclusive studies.  However like most people on melodeon.net I have heard people waffle on until they are blue in the face about it and it's clear lots of people have opinions and hunches in different directions based on what they've seen and done ... I'm one of them.

My hunch is that the more rigid the structure that carrys the reed plate, the louder and more raw/direct the reed sound will be.  Anything which would allow the reed-plate to vibrate, or the reedblock to vibrate, or the fondo to vibrate will be taking energy out of that system and it is this which allows the boxes to have their distinctive sounds even if they use the same reeds.  I have taken that in to consideration but I won't talk about it much here as it's just an old can of worms that has been opened many times before and is not particularly appetising given that I know I'm not sure of my own thoughts and neither should anyone else be!

A gasketless box would be interesting to see how it sounded, but I think ultimately it would be too hard to get air-tight.  The wood would have to be unbelievably flat and the reed plates flawless.  I want to experiment ... but ultimately I want a set of working reedblocks.  I'm enjoying the journey.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!
Pages: 1 2 [3] 4 5 6   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal