Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 2 3 [4] 5 6   Go Down

Author Topic: Reed blocks ... come on then - how do you do it?  (Read 25416 times)

0 Members and 1 Guest are viewing this topic.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #60 on: December 06, 2017, 01:17:09 PM »

Boxcall ... I think you hit the nail on the head when you talk about the grain running in the wrong direction especially with respect to this particular project which has very thin dividing sections between the reed chambers.  Apart from the struggle to cut accurate straight lines (user error), the failings have been when the wood has split with the grain at these weak points.  Of course, once the wood is assembled and glued together in the reedblock, the whole thing is very much reinforced and I can't see it failing once in use.

Sugru is just an idea I had that may or may not work.  It is indeed a mouldable sillicone rubber which comes in little foil sachets (that have a use by date) it works like plasticine for the first hour or so after opening and cures in 24 hours to a solid but flexible and compressable rubber - in curing it also sticks like glue to most surfaces, but not to cling-film which can be used as a barrier if you wish to remove it with the option to glue it on later.  In my experience of using it - it can be removed with a bit of effort once bonded if you need to.  I don't know exactly how long it would last in a melodeon but sillicone rubber is a long-lasting material.  More of a concern to me would be that having a more "bouncy" gasket than is traditional might take some of the power out of the reeds by introducing flexibility in to the system, however I am anticipating screwing them down hard.

I imagined working the sugru in to thin sausages, lining them up on the areas around the reed chambers and then using a cling-film wrapped piece of flat wood to clamp/vice to the reedblock to squash it down to the desired thickness.  Then I was going to trim off the excess and clean up the chamber edges.  I wasn't planning on placing the reed plates at this stage to create moulds for them once cured although this could be a good idea.

Here's a picture of the block from sketchup showing what the lip looks like


You may have your block made up by now, but if you don't I would suggest running the grain top to bottom (rather than side to side of block)this would give you more strenght on the wood between the chambers.
you could leave the top long until you make all the cut outs then trim to final size, this would be to prevent spliting during the cutting process. then when you glue it to the piece that divides the chambers that would add strenght to the side to side movement in the grain, you could also add a thin strip of ply to the top of block to add more reinforcement.
advantage would be you now have a better area for screws between the chambers with the grain going up and down the block, if that makes sense.
assuming you are going to screw the reeds into the part between each chamber with the grain going side to side, I think you'll have problems with spliting.

After thought: what kind of wood are you using?
« Last Edit: December 06, 2017, 01:18:43 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Reed blocks ... come on then - how do you do it?
« Reply #61 on: December 06, 2017, 01:18:59 PM »

Be careful of "screwing them down hard". The reed-plates can distort causing the tongue to jam in the slot.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Phil B

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 118
Re: Reed blocks ... come on then - how do you do it?
« Reply #62 on: December 06, 2017, 02:43:33 PM »

Quote at the end of Squeezy's last post "I am enjoying the journey".  And although I have not contributed I am enjoying reading about it PB
Logged

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #63 on: December 06, 2017, 03:13:05 PM »

After thought: what kind of wood are you using?

American Ash - the wood I have is exactly the right thickness and width to make up these blocks without cutting to size ... however ... with the grain in exactly the wrong direction to do as you suggest!  I understand that for my purposes traditionally alder would be used.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Reed blocks ... come on then - how do you do it?
« Reply #64 on: December 06, 2017, 03:19:56 PM »

That question about what type of wood (and also the grain direction) really highlights the necessity of designing to accommodate the strength/rigidity requirements against the constraints of available space!  Ikeep thinking that milling from a solid block of aluminium should be ideal.  The whole thing would be more rigid and machine screws could be tapped into the body, smaller and more secure than woodscrews.  This is just the sort of project that used to be done as "homers" in major engineering works.  It was even accepted by management as it kept the machinists on top of their game, guaranteeing that the model shop could produce close tolerance, high tech components from a hand-drawn sketch - as long as the correct parameters were identified to ensure functionality.

If it were milled from solid, the only area of concern would be the radius in the chamber corners - probably best drilled before milling to ensure clearance for the reeds' maximum excursion.  I like the idea of the rim to hold one end of the reed plate.  If it were adjustable, it might well be sufficient to hold all the plates against a gasket!  I wonder how consistent the thickness of a reed plate is?

Rob
Logged

ChrisLDD

  • Good talker
  • **
  • Offline Offline
  • Posts: 64
  • ... but which way is up?
Re: Reed blocks ... come on then - how do you do it?
« Reply #65 on: December 06, 2017, 03:57:49 PM »


I imagined working the sugru in to thin sausages, lining them up on the areas around the reed chambers and then using a cling-film wrapped piece of flat wood to clamp/vice to the reedblock to squash it down to the desired thickness.  Then I was going to trim off the excess and clean up the chamber edges.  I wasn't planning on placing the reed plates at this stage to create moulds for them once cured although this could be a good idea.


Interesting idea regarding the sugru ... maybe some sort of rubberized glue/paint, applied to the surfaces and allowed to dry before the reeds are fixed?
Logged
Trying to learn enough magic to make my own melodeon.

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Reed blocks ... come on then - how do you do it?
« Reply #66 on: December 06, 2017, 04:40:00 PM »

Looking at Boxcalls sketchup drawing - could the block be cut out of ply which may solve the grain direction problem?
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #67 on: December 06, 2017, 05:35:25 PM »

That's Squeezy's drawing not mine, and He's wanting to do this with a solid piece of wood.

American ash is good straight grain wood But that could work against what you are doing depending on the piece as it can vary.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Reed blocks ... come on then - how do you do it?
« Reply #68 on: December 06, 2017, 08:27:34 PM »

Sorry re drawing (which is very nice Squeezy) I wasn't thinking - but ply or laminating one's own block would help with the grain direction problem
Logged

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Reed blocks ... come on then - how do you do it?
« Reply #69 on: December 06, 2017, 10:51:55 PM »

Ash has open pores and best for baseball bats and body framing on Morgans.

Alder is closer to an (a) homogenous wood.  Little grain/pores and easy to machine.  Usually free from twist, cup, wind, and voids.
Also much lighter than ash.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #70 on: December 07, 2017, 12:01:37 AM »

Ash does bend nicely with those open pores.
Elm would be good as it has interlocking grain. Not very easy to work.
Fruit wood / black cherry etc. could be use. Works easy. The wood resists warping and splitting during seasoning and remains stable ad strong, think furniture, instruments, sculpture.

I've got a good pile of cherry I got it from my father in law when he passed. Need some?
I could even plane to a thickness for you.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #71 on: December 07, 2017, 01:29:06 PM »

Thanks for the offer.  I may still take you up on it but I have to ruin what I have first ;-)

Actually I managed to cut a successful pair of fairly accurate combs from the ash using the scroll saw this morning!  They're currently in a vise glueing together with the separating plate.  It's quite exciting - they line up and really look like a proper reedblock.

Scroll-sawing is something I haven't done so much of in the past and it is amazing when it works - however it needs a lot of practice and fiddling about with different blades, speeds and settings to get exactly the cut you are looking for!  And it can only cut straight lines if you can ... it's sort of the opposite of a table saw.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Reed blocks ... come on then - how do you do it?
« Reply #72 on: December 08, 2017, 01:02:33 AM »

Thanks for the offer.  I may still take you up on it but I have to ruin what I have first ;-)
That's a good Idea! you have got a lot of work into it by now,I'm sure.
Are you using Ash or hard wood for the separation piece also? Or plywood.

I'm glad everything is working out so far and your happy with it.

BC
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #73 on: December 08, 2017, 08:28:35 AM »

The separating plate is lime (basswood)

I'm happy(ish) with it - it could be neater, but all the reeds fit in the chambers as they should and they seem to be air-tight.  I'll continue building this and use it to practice all the other building techniques - my first attempt at drilling holes accurately on the bit that goes on the fondo was less successful!  I will probably use this one to mess around with sugru and see how that works and how it all sounds in the box.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Reed blocks ... come on then - how do you do it?
« Reply #74 on: December 08, 2017, 09:02:43 AM »

If you want any Maple to play around with I have loads,,Just pay postage and a small Cancer charity donation I can post it,I often have 15 x 21mm sections all planned
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #75 on: December 08, 2017, 09:26:06 AM »

Thanks for the offer Pete ... that's very kind, I will bear that in mind.

Meanwhile this is what I've ended up with:
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed blocks ... come on then - how do you do it?
« Reply #76 on: December 08, 2017, 09:42:51 AM »

....I will probably use this one to mess around with sugru and see how that works and how it all sounds in the box.

I didn't know what Sugru was until reading this thread and I did some digging around.
Are you planning on using the Sugru simply as a gasket or as a substitute for wax/nails/screws for actually holding the reed plates in place?

If the latter, there could be some awkwardness in temporarily removing the reed plates and re-fixing afterwards. The reasons you might want to do this could include:
  • Adjusting the positioning of the reed plate if an underneath valve is fouling the sides of the reed chamber
  • Changing a valve on the underneath side
  • Flipping an accidental or other reversal
  • Fine tuning (particularly sharpening) one of the very small and delicate high-pitched underneath reeds. Sometimes it is better to temporarily flip the reed plate, work on the reed tongue and then re-flip the reed plate to its proper position. This is a safer option, posing less risk of damage to the reed tongue which might otherwise result from using a reed lifter or hook to pull the reed tongue up through the slot.

Just my thoughts. Although experimenting is always a worthwhile activity, wax, nails and screws have been in successful use for a long time for good reason. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #77 on: December 08, 2017, 09:48:41 AM »

I'm planning on just using the Sugru as a gasket and also using screws ... the idea being that it will be quite forgiving in the same way that wax would be with my less than perfect micro-woodworking skills!
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Reed blocks ... come on then - how do you do it?
« Reply #78 on: December 08, 2017, 09:55:24 AM »

I'm planning on just using the Sugru as a gasket and also using screws ... the idea being that it will be quite forgiving in the same way that wax would be with my less than perfect micro-woodworking skills!
That should work then! Just make sure all your underneath valves are working properly and not fouling the reed chamber sides, before tightening down the screws too much.

I shall continue to follow this thread with interest.  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Reed blocks ... come on then - how do you do it?
« Reply #79 on: December 08, 2017, 11:16:35 AM »

What I can definitely say about this method of cutting the comb from a single piece of wood is that it is far more stable than I imagined once it is all glued together and I would be perfectly happy to use a bench belt sander to profile it ... sadly I don't have one!  One for the Xmas present list!
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!
Pages: 1 2 3 [4] 5 6   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal