Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Castagnari glue  (Read 4600 times)

0 Members and 1 Guest are viewing this topic.

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Castagnari glue
« on: December 12, 2017, 03:08:19 PM »

https://www.youtube.com/watch?v=ZZj9a9nP8lc


Can someone please translate from 4:45 to 7:00 minutes.

Is this large stainless pot heating hide glue or TiteBond II   ?

Thanks
Logged

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Castagnari glue
« Reply #1 on: December 12, 2017, 03:49:56 PM »

He says it's rabbit-skin glue (colla di pelli di coniglio). 4:53. I was expecting this because I translated a different Castagnari video a while back, in which he said the same thing.

Also, it's a bain-marie (double-boiler, to Americans. The pot holding the glue is sitting in a boiling-water bath).

http://forum.melodeon.net/index.php?topic=16217.0
« Last Edit: December 17, 2017, 08:32:06 PM by Stiamh »
Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Castagnari glue
« Reply #2 on: December 12, 2017, 06:02:08 PM »

Titebond II is a waterproof synthetic resin glue, and is used cold, straight from the container. It's a very good adhesive - I use it a lot. The glues that need heating in a double gluepot are by and large hide glues or other animal-derived adhesives; rabbit-skin is one of the traditional luthier's adhesives and again, very good - and again I use quite a bit of that.  Each adhesive is good in its own "home" circumstances - for instance, joints that might need to be taken apart are best made with hide glue.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Stiamh

  • Old grey C#/D pest
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3611
    • Packie Manus Byrne
Re: Castagnari glue
« Reply #3 on: December 12, 2017, 06:41:25 PM »

Signor Castagnari goes on about the virtues of the skin glue - in his view, it transmits sound well by forming a crystalline structure, doesn't cause wear on tools (unlike vinyl glue), and so on. All the same stuff he said in the other video I linked to. Haven't got the energy to translate it all.

You can use the subtitle feature to get a few helpful glimpses - though use with caution. I'm amazed at what the system manages to transcribe accurately, and even more amazed at the sentences it is completely off the mark with. Quite entertaining...
« Last Edit: December 12, 2017, 06:43:03 PM by Stiamh »
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Castagnari glue
« Reply #4 on: December 12, 2017, 07:03:21 PM »

During my career, I've repaired a substantial number of Castagnari casings with cracked corners and re-glued many of those triangular bass corner pieces. Must have been something wrong with the rabbit, I guess.
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Castagnari glue
« Reply #5 on: December 12, 2017, 07:26:28 PM »

Animal glue / Pearl glue smells foul but has it's uses - best glue for hand veneering because as it dries it draws or pulls the veneer onto the surface.
Logged

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Castagnari glue
« Reply #6 on: December 15, 2017, 08:58:29 AM »

Animal glue / Pearl glue smells foul but has it's uses - best glue for hand veneering because as it dries it draws or pulls the veneer onto the surface.

That’s interesting, because in my experience Pearl glue doesn’t smell. Stale Pearl does have a slight tang to it but only in a “workshoppy” kind of way.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Castagnari glue
« Reply #7 on: December 15, 2017, 09:29:53 AM »

That’s interesting, because in my experience Pearl glue doesn’t smell. Stale Pearl does have a slight tang to it but only in a “workshoppy” kind of way.
I know a joke about that, but it's well off topic.

Maybe people have different sensitivities (cf asparagus)? Or the glue varies?
I detect a slight smell from pearl glue, but it's not overpowering. Or, as Nick says, out of place in a workshop.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Castagnari glue
« Reply #8 on: December 15, 2017, 02:29:27 PM »

May just be me as I can't stand the smell of fish, cat food etc. or it could have been an old batch or mixed in with some other animal glue.
Logged

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Castagnari glue
« Reply #9 on: December 15, 2017, 07:57:03 PM »

Sounds suspicious to me Gromet. Pearl glue, which we affectionally call hoof & horn really doesn’t smell. Are you using it in a double boiler?
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Castagnari glue
« Reply #10 on: December 15, 2017, 09:03:15 PM »

During my career, I've repaired a substantial number of Castagnari casings with cracked corners and re-glued many of those triangular bass corner pieces. Must have been something wrong with the rabbit, I guess.
Maybe the stuff is not flexible enough, or were they dropped?

Possibly better for sound but more brittle as the wood moves.

Do most people that use this glue (size the joint)? Which is a term I know for applying a glue mix with water letting it soak in for couple of minutes or so then apply a bit more to make up for the amount that soaks in to the wood, this makes for a stronger joint or bond. I do this on all my end grain glue ups as well as edge to edge when there is time for it, I don't always use a mix but find just applying the glue itself works for me.

Quote from titebond:
"Get good results gluing end grain joints.
Although good joint design minimizes the need for gluing end grain, sometimes end grain joints are unavoidable. The strength of end grain joints can be improved if the "open" end grain is first sized. A sizing mixture may be made by mixing one part to two parts water to one part glue. Place the sizing mixture on the end grain. Let it soak in for no more than two minutes, and then continue with a regular application of glue."
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Castagnari glue
« Reply #11 on: December 15, 2017, 11:06:36 PM »

Quote
Do most people that use this glue (size the joint)?

I'm a bit confused.  Do you mean sizing end grain joints for hide glue or for Titebond ??  Or maybe both ????

I've done it for hide glue.
Logged

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Castagnari glue
« Reply #12 on: December 15, 2017, 11:22:09 PM »

Quote
Sounds suspicious to me Gromet.
I think the stuff smells, what's suspicious?
I haven't used animal glue for years - at college and then just a few times for hand veneering jobs at a joinery shop, where the glue was looked after by an apprentice and yes a double pot was used. I've always thought it smelled foul, nearly as bad as the ammonia I've used for fuming oak.
« Last Edit: December 15, 2017, 11:55:38 PM by Gromit »
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Castagnari glue
« Reply #13 on: December 15, 2017, 11:43:28 PM »

Quote
Do most people that use this glue (size the joint)?

I'm a bit confused.  Do you mean sizing end grain joints for hide glue or for Titebond ??  Or maybe both ????

I've done it for hide glue.
Yes I mean in general, but mostly referring to hot hide / animal glue.
Sizing should work for both types on end grain but I was wondering about the heated stuff as I don't use that in my trade, is there enough open with it? And do makers use the sizing for end grain.

I would think that a glue affected by moisture would not be the one to go with for instruments, not that they are exposed to it (like floating in a pond) much but there's moisture in the air. Might not effect a box that has finish on all surfaces. It does effect some though sticky buttons on wood levers when humidity is high is one example. I'm no expert on this just asking, a fellow who own a music store near by likes the fact that his building has high humidity, damp basement I think. He sells stringed instruments, must keep them from warping?

I don't use finger jointed wood on houses (when ever possible) because it always comes apart, even if coated with paints (4 sides)on exteriors and often on interiors as well.
Moisture and heat from the sun or others sources causes failure.
« Last Edit: December 16, 2017, 01:29:40 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

squeezy

  • Quick starter (now lagging behind)
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1317
  • Hohner Cornelia (mixte D/G/o&s)
    • www.johnspiers.co.uk
Re: Castagnari glue
« Reply #14 on: December 17, 2017, 01:18:51 AM »

Animal glues are used on instruments precisely because they are reversible, therefore the instruments can be taken apart for restoration and repair.  This is the norm in the violin world.  PVA wood glue is great stuff for a permanent joint, but my recent experience of making reedblocks shows that if you need to reverse set glue, pVA rips parts of the wood away all too easily making re-gluing very problematic.
Logged
Squeezy

Sometimes wrong, sometimes right ... but always certain!

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Castagnari glue
« Reply #15 on: December 17, 2017, 02:55:24 AM »

Skin glue / pearl glue is still widely used in fine carpentry and intarsia.

Should not be used in outdoor constructions!.  (building houses!)

if the environment is ok for wax  -  it is also ok for hide glue.  (- or  perfect for hide glue )    once you get used to it.

There have never been glue made on hoofs or horns, even if  the name is often used by old carpentry masters. 

Titebond II   (brown )  is very fine to use gluing wood to wood!
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

Chris Rayner

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 467
Re: Castagnari glue
« Reply #16 on: December 17, 2017, 01:36:43 PM »


There have never been glue made on hoofs or horns, even if  the name is often used by old carpentry masters

Yes there have.  Hooves and horns together with bones and sinew and other inedible parts were used to make glue.  Such glues were the oldest produced, and were used by the Ancient Romans, Ancient Egyptians and even North American Indians from the hooves and other parts of their ungulate prey.
Logged
Elderly amateur musician hoping to stave off dementia by learning to play the melodeon.  Main instrument a Tommy, also D/G and G/C pokerworks,  a single row 2 stop Hohner, and a new addition to the free reedery, a rather splendid Paolo Soprani four voice 120 bass c-system chromatic button accordion.  Very shiny, very loud, and about the same size and weight as a small car.  Now I’ve traded me Benny with (ahem) a cash adjustment, to a three voice 60 bass Castagnari K3.

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Castagnari glue
« Reply #17 on: December 17, 2017, 02:02:23 PM »

"Such glues were the oldest produced, and were used by.........Ancient Egyptians"

I don't really know anything about glue, other than the stuff that I've used usually comes in tubes! However......in a short cul-de-sac street not very far from our home in Luxor Egypt, it is not unheard of to find the empty shells of small hooves lying about in the roadway. I've often wondered if the former contents of these hooves were being used to make glue, but don't have the Arabic to ask. Ancient Egyptian practices (and mindsets) are still VERY evident in the (so-called) modern Egypt.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Castagnari glue
« Reply #18 on: December 17, 2017, 03:22:15 PM »

Thanks for all the replies and comments.

I understood a bit of the narrative but what confused me was the jug of Titebond and the double boiler for "hide" glue".

I have been making stringed instruments since 1964 and used a variety of glues to include traditional animal based . I went vegan for some time but the early Titebond and Elmers and so on were not so good. I have used urea and epoxy, recorsinal (resorcinol)   and among the worst are pre mixed bottled "hide" glue. Which is not "hide glue". Brown trash.

For 30 years now the majority of my instruments , to included reeded, have been a combination of Titebond , LMI ( Luthiers Mercantile Inc. ) and principally... fish glue. Fish glue has all the best characteristics of hide glue and none of the drawbacks.
I have passed this on to a few current box makers and classical/flamenco guitar and mandolin makers.  My neighbor and professional guitarist  Ray Reussner( 40 year student and friend of Segovia and subject of a 1960 PBS special .. Master Class with Segovia) turned classical guitar maker about 20 years ago.. upon my suggestion switched from hide glue to fish glue.

In my 20 years of making European vernacular furniture I opted for Titebond for the majority of my work.  Not traditional, but the right application for pieces that should not come apart.

I appreciate this quote... and have discussed this with Cajun  accordeon makers and players frequently over the years...

Quote from titebond:
"Get good results gluing end grain joints.
Although good joint design minimizes the need for gluing end grain, sometimes end grain joints are unavoidable. The strength of end grain joints can be improved if the "open" end grain is first sized. A sizing mixture may be made by mixing one part to two parts water to one part glue. Place the sizing mixture on the end grain. Let it soak in for no more than two minutes, and then continue with a regular application of glue."

The key phrase here is ... "although good joint design minimizes the need for gluing end grain".  Not yet recognized by the "big 3" Cajun box builders who have yet to discover miters.


Thanks Steve for the translation.

I'll stick with my Titebond II and fish glue.

And, Diatonix, thanks for the observation on the Castagnari cracked corner failures... crystalline?  .. may mean wrong temperature, wrong mix therefore too brittle?

« Last Edit: December 17, 2017, 03:26:08 PM by melodeon »
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Castagnari glue
« Reply #19 on: December 17, 2017, 04:02:15 PM »

I’m also a convert to fish glue, especially for repairs to old woodwork originally made with animal glue.  It has the advantage of a long open time compared with hot hide glue, so you have time to work it well into a joint that can’t be fully dismantled.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal