Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: some tuning questions  (Read 2170 times)

0 Members and 1 Guest are viewing this topic.

jorden

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 108
some tuning questions
« on: December 15, 2017, 07:09:20 AM »

I'm in the process of converting two Hohners (Bb/Es & C/F) to B/C and C#/D. I'm starting with the B/C. I've just finished taking the Bb-row up a half-step on the tuning table. After this I will revalve them and wax them in and do the fine tuning with the blocks in the box.

A few questions:

- for the initial tuning on the tuning table: do you aim for a few cents sharp/flat or just at pitch? Or is the effect of revalving and waxing in the block too random to predict at all?
- during the finetuning with the blocks in the instrument: any tips for adjusting the setting of the pull reeds? Or is this just something that requires a lot of patience and tolerance to frustration?
- I find that the reeds misalign quite quickly when using a file. Is this normal or should I be more delicate?

Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: some tuning questions
« Reply #1 on: December 15, 2017, 08:36:43 AM »

See this recent topic for answers to your tuning question:
http://forum.melodeon.net/index.php/topic,21408.0/nowap.html

Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: some tuning questions
« Reply #2 on: December 15, 2017, 09:30:03 AM »

- during the finetuning with the blocks in the instrument: any tips for adjusting the setting of the pull reeds? Or is this just something that requires a lot of patience and tolerance to frustration?

Before you start fine-tuning with the blocks mounted inside the instrument, or indeed any tuning at all, I would recommend that you test and adjust the setting of all the reeds. This is best done with the reeds mounted on the blocks, but outside the instrument. You need to sound each reed under gentle tuning bellows pressure, checking that each reed speaks promptly, i.e. no breathy delay. But also the sound needs to be strong and consistent with little or no change of pitch when the bellows pressure is increased; and no choking off under increased pressure either.

This process is probably the most exacting, but ultimately most rewarding, steps in reed work. It can be very frustrating and needs a lot of practice, care and patience, but it can make the difference between an instrument which plays really well, compared with one which only plays in a mediocre way. The setting of the reed gap also depends on the ultimate style of the player. Someone who needs a robust sound for outdoor morris playing will need a very slightly wider setting than someone who plays indoor solo gigs.

I think the ideal workflow for reed work is like this:

  1. Check all wax (if used) is secure and all valves are lying flat and functioning properly. Replace if not.
  2. Reed blocks out of instrument: Test reed response and adjust set of reeds to give optimum response, as described above.
  3. Replace blocks in instrument. For normal playing pressures, record the actual pitch of each reed and make a note of the deviations from Equal Temperament (or whatever pitch system you are using). You will need to isolate different banks of reeds for the different voices, e.g. so that you are just working on either the M or the M+ reeds but not both together.
  4. If the pitch deviations are relatively small, you can then start to tune the reeds in situ in the instrument. Larger deviations (8 - 10 cents or more), might be best dealt with outside the box.

Tuning the reeds may affect the gap setting slightly, so after a first pass at tuning you might want to check the response again and adjust if necessary. Then repeat steps 3 and 4 as necessary until the tuning is correct.

Quote
- I find that the reeds misalign quite quickly when using a file. Is this normal or should I be more delicate?
Assuming that you are supporting the reed tongues properly whilst filing or scratching, I would suggest that you are being too enthusiastic and using too much pressure. Care and delicacy is good, as is a sharp, good quality, fine-cut file. Alternatively you could use a fine (400 grit) diamond file. The diamond files sold by Charlie Marshall for reed tuning are about 100 grit grade and are too coarse for anything but the very largest and heftiest bass reeds.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: some tuning questions
« Reply #3 on: December 15, 2017, 09:45:43 AM »

..on reed misalignment, try filing towards the rivet rather than crosswise, and use a bright light to watch your cuts. And anyway if you are tuning with the blocks in situ, you pretty much have to file downwards or at a slight angle to the reed, which should prevent this happening. But as Steve has said, use a v sharp file...so buy a new one and don't store it against other tools...keep it in its own bag. You require surprisingly little pressure to tune with a sharp file.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: some tuning questions
« Reply #4 on: December 15, 2017, 10:55:29 AM »

Why shouldn’t you store it against other tools Rog?.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: some tuning questions
« Reply #5 on: December 15, 2017, 10:59:08 AM »

Why shouldn’t you store it against other tools Rog?.
To stay on the straight and narrow, you need to be in single file mode.

Which also prevents knocking the teeth and damaging or blunting them. Regard each tooth as a cutting edge.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: some tuning questions
« Reply #6 on: December 15, 2017, 11:58:21 AM »

Why shouldn’t you store it against other tools Rog?.
To stay on the straight and narrow, you need to be in single file mode.

Which also prevents knocking the teeth and damaging or blunting them. Regard each tooth as a cutting edge.
Yes that's kind of my assumption - it's what I was taught back in the mists of time on my 'fitting' engineering training module....basically six weeks of filing and hacksawing bits of steel. But I have noticed that files kept in a tool box and jostled by other tools do lose their sharpness. So I'm always careful with them.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: some tuning questions
« Reply #7 on: December 15, 2017, 01:37:08 PM »

I have pinned a thin strip of steel to the side of my tuning table (a length of pallet strapping from work, as it happens). I have drilled a 6mm hole in the handle of each file, and fitted a rare earth magnet, at a cost of pennies. The files hang on the side of the tuning table.
The files are protected from accidental damage and I know where they are.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

jorden

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 108
Re: some tuning questions
« Reply #8 on: December 18, 2017, 09:15:00 PM »

Thank you all for your replies (:) That will keep me going in the right direction (and with a better overview hopefully of the tuning/setting process). I'm already very careful with my Vallorbe-files, but I will definitely get a better lightsource.

Filing from the tip of the reed in the direction of the rivet seemed counterintuitive to me (afraid of damaging the edge of the tip), but I'll give it a try and see if it helps with the misaligning.

Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: some tuning questions
« Reply #9 on: December 18, 2017, 09:48:58 PM »

I'm using the sand paper on the stick, it's working great and it does not seem to grab the edge of reed as much as a file. Could be my file isn't fine enough? Also I'm working off the block at the moment.
I'm working across the tip or middle of reed, I'm finding the closer you get to where you want it to be go easy for it's easy to take to much and then you have to go back. Also where scrather has been use even lighter amount needs to be taken as more material comes off sanding 90 degrees to ridges.
Also same thing with smaller reeds and even more so.
I was cruising though the C row then it all fell apart at the high reeds, they are fussy  >:(
I also have the high G giving me fits not speaking, grrrr.
And my index finger that's holding the reed steady when sanding is also feeling my pain, I'll probably have a callous after this.

I'm off to get that G note going, Good luck with your tuning!!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: some tuning questions
« Reply #10 on: December 19, 2017, 01:02:53 AM »

I'm using the sand paper on the stick, it's working great and it does not seem to grab the edge of reed as much as a file. Could be my file isn't fine enough? Also I'm working off the block at the moment.
I'm working across the tip or middle of reed, I'm finding the closer you get to where you want it to be go easy for it's easy to take to much and then you have to go back. Also where scrather has been use even lighter amount needs to be taken as more material comes off sanding 90 degrees to ridges.
Also same thing with smaller reeds and even more so.
I was cruising though the C row then it all fell apart at the high reeds, they are fussy  >:(
I also have the high G giving me fits not speaking, grrrr.

One thing I've found when filing or wide-scratching* the belly of the reed to flatten it: removing steel from the reed surface in this way tends to alter the stresses in the reed tongue which causes it to curve or bend down slightly. This reduces the reed tip gap or even cause the reed tongue to become almost flush with the reed plate. This in turn is enough to cause the reed to choke off, or not sound at all.

The remedy is, after filing/scratching, to use the reed 'pinger' to ease the reed tongue upwards by pinging it or gently lifting it a few times. This has the effect of re-setting the tip to its proper gap and the reed should then speak normally. I guess the pinging/flexing redistributes the stresses.

Dave Elliott in his 'Concertina Maintenance Manual' also reports this phenomenon when dealing with traditional concertina reeds.

* By this I mean using a wide scratcher with a square profile having a width similar to the width of the reed tongue. These definitely cause the reed bending down effect. On the other hand, using a fine circular cross-section scratcher to make very narrow scratches renders the reed tongue much less prone to the bending down effect.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: some tuning questions
« Reply #11 on: December 19, 2017, 04:57:32 AM »

Quote
One thing I've found when filing or wide-scratching* the belly of the reed to flatten it: removing steel from the reed surface in this way tends to alter the stresses in the reed tongue which causes it to curve or bend down slightly. This reduces the reed tip gap or even cause the reed tongue to become almost flush with the reed plate. This in turn is enough to cause the reed to choke off, or not sound at all.

The remedy is, after filing/scratching, to use the reed 'pinger' to ease the reed tongue upwards by pinging it or gently lifting it a few times. This has the effect of re-setting the tip to its proper gap and the reed should then speak normally. I guess the pinging/flexing redistributes the stresses.

I've observed this too.  I thought the change in reed set was due to the way I was supporting it while filing.
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal