Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Setting reed gap  (Read 5552 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Setting reed gap
« on: December 27, 2017, 12:27:41 PM »

What is best practice when setting reed gap, in terms of the actual mechanics of the process? So far, I have only had to raise the gap slightly (on an instrument where the note would not speak otherwise) which I accomplished by simply prying the reed back gently from the near the tip. Is it as simple as this? I want to avoid potentially damaging, or even breaking a reed in the process. What about lowering gap? Is there a specific way to do this? I'm guessing you "push" the reed towards the slot. Does it make more sense to make the adjustment from a certain part of the reed?
Logged
C#/D player

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Setting reed gap
« Reply #1 on: December 27, 2017, 03:20:24 PM »

What is best practice when setting reed gap, in terms of the actual mechanics of the process? So far, I have only had to raise the gap slightly (on an instrument where the note would not speak otherwise) which I accomplished by simply prying the reed back gently from the near the tip. Is it as simple as this? I want to avoid potentially damaging, or even breaking a reed in the process. What about lowering gap? Is there a specific way to do this? I'm guessing you "push" the reed towards the slot. Does it make more sense to make the adjustment from a certain part of the reed?

For lowering the gap on the push reeds on top of the reed plate, I use a wooden cocktail stick applied to the middle of the reed tongue to push the tongue gently down just into the slot, and then release it. For the larger reeds I use either a wooden skewer - the heavy-duty version of the cocktail stick - or else a soft steel dental descaling tool. The latter is soft enough to not scratch the reed tongue. (NB - search on-line for dental tools for sale).
The very small highest pitched reeds are very delicate of course, and it is very easy to bend them too far and permanently damage the reeds. Be very careful!

For the pull reeds on the underside, the descaling tool is useful as it has a hook-shaped end which I can insert through the reed chamber opening and push the reed tongue upwards into the slot.

The important point is to go very gently a little bit at a time and keep testing all the time to check whether the reed is responding at its optimum. It may not be possible to see visually whether you have made any difference, so checking on the tuning bellows is the only way. Reeds which have too narrow a gap may still speak readily, but the pitch will vary with bellows pressure and at higher pressures will probably choke off.

You need a lot of patience, practice and determination to get the gap set correctly: 'about right' is not really good enough. All reeds will have a sweet spot at which they respond the best and when you get this right, it is very rewarding and well worth spending the time on it.

Theo showed me how to do this gap setting process, so I'll say 'thanks' publicly again!  (:) :|glug


Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Setting reed gap
« Reply #2 on: December 27, 2017, 03:37:49 PM »

Thank you, Steve! That's very much the input I was looking for :)
Logged
C#/D player

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Setting reed gap
« Reply #3 on: December 28, 2017, 08:17:11 AM »

A *rough* guide to the reed gap is that it is the same as the thickness of the reed tip - or that is a good place to start if the reed is badly distorted. Also, try and keep the reed tongue as parallel to the slot as possible (it should not have a noticeable curve or kink). If it gets out of alignment with the slot, use a feeler gauge blade to coax it back.

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Setting reed gap
« Reply #4 on: December 28, 2017, 12:10:23 PM »

That is a very rough guide, and if the reed plays it won’t help you much in improving reed response, and may result in making things worse.  The optimum gap is larger for large reeds and smaller for small reeds, but it also depends on the quality of reed and can be different depending on how gently or vgourously you play. 
Top quality reeds need smaller set than lower quality, and scale length can make a difference too, though there m not sure which way!
The only practical way is trial and error as described previously by Steve.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Setting reed gap
« Reply #5 on: December 28, 2017, 01:04:27 PM »

The optimum gap is larger for large reeds and smaller for small reeds,
Yes, I found this to be the case in the reeds I'm working on.  Smaller reeds almost nothing it seemed.
I also noticed when gaping the reeds that they would go flat upon widening the gap.
So adjusting pitch may be needed after setting gap, probably goes without saying.
My very limited experience of course.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Setting reed gap
« Reply #6 on: December 28, 2017, 01:10:58 PM »

Yes pitch tends to go flat after adjusting the set,  that’s normal.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Setting reed gap
« Reply #7 on: December 28, 2017, 05:31:43 PM »

I had to go and check my reference to reed gap setting ... in the Benetoux book (Sounding out the accordion) he says under Reed Settings '...Generally speaking the reed should remain the equivalent of one layer of thickness above the reed plate [but] this rule does not apply to weighted reeds'. He points out that this is a 'factory type' setting which doesn't apply in all cases (he gives a couple of examples).

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Setting reed gap
« Reply #8 on: June 14, 2019, 07:32:42 PM »

Is there a video floating around showing someone setting the gap? 
Logged
Hohner Club IIB Victoria

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Setting reed gap
« Reply #9 on: June 14, 2019, 08:01:12 PM »

Is there a video floating around showing someone setting the gap?


Soon  8)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Setting reed gap
« Reply #10 on: June 14, 2019, 08:06:06 PM »

In the meantime there's this, but I don't mind admitting that it made me wince a few times!

Setting the gap.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Setting reed gap
« Reply #11 on: June 16, 2019, 10:41:06 PM »

I'm looking forward to Lester's video on the subject. With his example I'm sure I will be able to try this again with renewed confidence. (and success)
Logged
Hohner Club IIB Victoria

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Setting reed gap
« Reply #12 on: June 21, 2019, 08:29:23 AM »

There are other gapping considerations regarding how the gap progresses back from the tip also.

I helps a bit if you understand that it is not the pressure of the air that makes the reed beat as much as the venturi effect of the are rushing through the gap on the tip and sides.

The reed is basically sucked down and this suction stops the second the gap closes , the reed continues a bit with momentum then bounces back, gap appears and cycle repeats.

Gap is too small and the reed can't spring back against air pressure, too big and vacuum can't pull it closed against spring tension so it is slow to start or takes a lot of pressure.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Cag

  • Member
  • *
  • Offline Offline
  • Posts: 44
Re: Setting reed gap
« Reply #13 on: June 27, 2019, 01:51:38 PM »

Pretty much all of my experience is with concertina reeds but this brings with it unique advantages; the set is adjusted with the entire reed assembly in your hands, and more importantly, you can put it under a microscope and see exactly what is happening with the reed shape.

Opinion alert! The usual suggestion of one thickness of the reed higher than the frame is not a bad one but ignores the shape of the reed to that point. It is possible to create a shape which will end up one thickness high at the tip but on the way it will create an inefficient reed. My own personal model of reed shape relies on making a curve which, when the reed is sucked down into the slot, will mean the entire reed enters the top of the slot at exactly the same time. At this moment the reed creates a “compression point”  (I named it this in memory of Phil Irving and his book Tuning for Speed and the phrase “compression is acceleration”) as it is briefly sealing the slot as much as the clearance around the reed allows. As well as efficiency dividends this has implications for the tone as the higher partials created by a reed flashing past the tightest point all at the same time are different to those created by a curved reed where the tight point travels along the reed as it swings through.

In order to get the compression point happening it is necessary first to make sure the parts of the reed which cannot bend, the root and on lower reeds a section before the tip, are straight. The straight root section needs to be bent down just a tiny bit to make sure it is “sealing”. When you can’t see any light under the stiff root section it is where it should be. Next, in order to create the right shape in the reed you need to gently bend it upwards and note where it bends easiest. This is where you need to bend the reed upwards and make a permanent bend. When you have done this you can check whether the reed “seals” when down by pushing down on the reed in an appropriate spot, with a low note this is about 3/4s of the way to the tip.

Next the height of the uplift needs to be set and you can guess this but the best adjustment is made by assembling the instrument and then trying the reed with a strong pull to see if it chokes and a soft start to see if it is reluctant to start at low pressure. Disassemble, adjust, assemble etc.

Earlier I mentioned reeds which could have the tip approximately at the right height but are let down by the shape before the tip. Such shapes are common in reed organs which employ all sorts of tricks to create different tones for each stop. Some reeds have a large twist at the tip of the reed, and others have a shape which lifts immediately from the root, arches up and then down to about one reed thickness above the frame. Both of these shapes would create a more mellow sound with fewer high frequencies at the cost of efficiency though this is less of a problem in organs because they have endless air/vacuum available. I have seen a concertina with the arched shape, it was a fairly ordinary instrument, a Wheatstone out of Africa. When I went through and made the shape conform to the shape as above the instrument came alive in response and volume.

Sorry I went on a bit, hope someone finds it at least interesting and even helpful.
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Setting reed gap
« Reply #14 on: June 27, 2019, 11:34:31 PM »

You also need to consider how the instrument will be played. Years ago somebody (Colin Dipper?) fettled my wife's G/D Crabb, when she got it back the reeds spoke at the merest touch. However when played harder for morris -- the main use for her -- they choked horribly and didn't sound half the time. If you want to play quietly and fast the reeds should be set lower than if you want to play loudly...
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Setting reed gap
« Reply #15 on: June 28, 2019, 12:29:02 AM »

...Sorry I went on a bit, hope someone finds it at least interesting and even helpful.

Thank you Cag
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Cag

  • Member
  • *
  • Offline Offline
  • Posts: 44
Re: Setting reed gap
« Reply #16 on: June 28, 2019, 03:20:38 AM »

You also need to consider how the instrument will be played. Years ago somebody (Colin Dipper?) fettled my wife's G/D Crabb, when she got it back the reeds spoke at the merest touch. However when played harder for morris -- the main use for her -- they choked horribly and didn't sound half the time. If you want to play quietly and fast the reeds should be set lower than if you want to play loudly...
Absolutely, nothing harder than tuning and setting an instrument for a person when you don’t know how they play. Not just the height of the reed above the frame but when the instrument has thinner low reeds you need to know their typical playing pressure or their chords will be dreadfully out of tune. This is less true of modern instruments which tend to be more pitch stable.
Logged

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Setting reed gap
« Reply #17 on: July 22, 2019, 01:22:23 AM »

Mr. Bailey, If you make a video showing the setting of the reed gap, could you also address resetting loose reeds? How to tighten the rivet and re-position the reed? I dabbled in some of this today and I think I got through it, but it would sure be nice to see an example of the correct way to do such things.
Logged
Hohner Club IIB Victoria
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal