Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: different tones with same reeds  (Read 4385 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
different tones with same reeds
« on: January 16, 2018, 04:29:33 AM »

I'm curious about differences in tone, volume and reed response in one-row, 4-stop boxes that are of similar construction and contain the same type of reeds.  Using the example of one-rows (with functional stops) that are built with Binci Professional reeds, I've noticed a difference in both tone and volume in several boxes side by side.  Tuning aside (removing the M+ bank of reeds and using only LMH) you'd think that the sound from each box would be more or less the same, but I've noticed that they are noticeably different, at least to my ear.  What would make the same reeds sound so different from one box to the next?

Volume and the way in which the reeds seem to respond also varies greatly.  I understand that reed gap can be adjusted, and my understanding has been that there is an optimum position for each reed that will allow it to perform best.  I also understand that the reed gap can be adjusted for greater volume, at the potential cost of reed response (correct me if I'm wrong, please).  But I've noticed several boxes, side by side, that all respond with the slightest amount of pressure, but one may speak quietly and softly, with volume increasing with bellows pressure, and another will shout at near full volume with very little pressure.  What might account for these differences, given that the boxes are of similar construction (four sets of reeds, two laid flat and two upright, holes in slides that are attached to stops) and all have Binci Professional reeds.  I'm really rather curious!
Logged
C#/D player

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: different tones with same reeds
« Reply #1 on: January 16, 2018, 05:51:55 AM »

Sounds like it's more about volume and tone since the reeds respond at low pressure and increasing?
Tone could be lots of reasons in the construction, I'm guessing.
I'm guessing again, for volume the size of hole in fondo, reed chamber depth, binci reeds may vary slightly?

I'll be interested to hear what the pros say also.

I'm having a hard time falling asleep so I'm just killing time here, I really should try again.
This probably doesn't happen to all you young bucks :D
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Julian S

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1628
  • D/G Pastourelle 2, Dony, Pokerwork, G/C Pariselle
Re: different tones with same reeds
« Reply #2 on: January 16, 2018, 08:20:06 AM »

Age of boxes - and how much they have been played obviously also has an effect - it would be an interesting exercise to swap round reed banks between instruments in the unlikely event that they would fit !
 I'm blessed (or cursed) with acute sensitivity to tuning so I really notice slight differences in tone between duplicate notes on my boxes. I can see that achieving precision in tone and responsiveness between the same notes dependent on whether they are on the press and draw must be problematic-it's the first thing I will check when I pick up my old Pastourelle 2 from the tuner this week. At least I've become more fond of my Castagnari Dony in the absence of my favourite box - truly they don't make them like that anymore ! But how to analyse the critical factors which come together to make the difference ?

J
Logged
Old Bones Dance Band

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: different tones with same reeds
« Reply #3 on: January 16, 2018, 09:33:41 AM »

If only it was all so simple, or rather, thank goodness it isn't!   :-\

The sound is at least as much in the structure of the accordion as in the reeds - in the design, critical measurements and materials.

Many of the best 10-key, 4-stopper melodeons today are based, directly or indirectly, on the products of the old International firm in Saxony, which manufactured both the Sterling and the Monarch models beloved of the Cajuns, and John Kimmel's/the Irish-American favourite Globe "Gold Medal" boxes, and I'm lucky enough to own and play one of the latter that (though nearly 100 years old) is in near-perfect condition and original tuning. It doesn't have Binci reeds (though I've had two Cajun accordions that did, and another with Salpa), but you'd be blown away by the sound that comes from it with its original Dix ones...

Edied to add John Kimmel - how could I leave him out? :o

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: different tones with same reeds
« Reply #4 on: January 16, 2018, 09:51:46 AM »

P.S. I've been saving an old set of Dix reeds for many years now, that came out of a seriously wormy International 4-stopper. It'd be very interesting to get a new Cajun box built around them, whilst making sure the chambering of the reedblocks, and the size of the holes in the soundboard, were exactly the same as on an International...

(Otherwise they'll have been tweaked to suit the Bincis these days!  ::))

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: different tones with same reeds
« Reply #5 on: January 16, 2018, 02:36:48 PM »

May I suggest M. La Fleur for such a project ?
Given that a "Cajun" accordeon is only a "Cajun" accordeon if made by a Cajun.
Logged

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: different tones with same reeds
« Reply #6 on: January 16, 2018, 03:42:29 PM »

May I suggest M. La Fleur for such a project ?
Given that a "Cajun" accordeon is only a "Cajun" accordeon if made by a Cajun.

If I ever have the money for it, I might well.
Butt my last "Cajun" accordeon was a Québécois, as would be any future one...

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: different tones with same reeds
« Reply #7 on: January 16, 2018, 03:50:51 PM »

Quote
Butt my last "Cajun" accordeon was a Québécois, as would be any future one...

We're speaking tuning here, not provenance, right ?
Logged

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: different tones with same reeds
« Reply #8 on: January 16, 2018, 03:54:03 PM »

Quote
Butt my last "Cajun" accordeon was a Québécois, as would be any future one...

We're speaking tuning here, not provenance, right ?

Exactly! (And it had butt joints... )  ;)

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: different tones with same reeds
« Reply #9 on: January 16, 2018, 04:43:56 PM »

I think the vibration of the reed tongue will be different if the box structure changes.  A couple of factors that may account for variation in the tone :
- the volume and shape of the reed chamber, size and 'depth' of hole, (and valve and pallet lining and whatnot) create an environment - think of it as a pneumatic spring or acoustical load - that varies from box to box.
- when the reed tongue vibrates, the free end chops the air flow but the riveted end 'shakes' the reedblock.  This mechanical vibration is transmitted to the box (which may contribute marginally to sound output) but is a loss or leakage from the reed tongue's perspective so that the air-chopping action is colored by the vibration going into the box.  An analogy: in a guitar the vibrating string pulls on the bridge and most of the sound comes from the soundboard being moved by the bridge.  But the string also pulls on the neck and this contributes to the sound.  Putting a weight (say a woodworking clamp) on the head will change the sound.

Just ideas...  if you think they don't make sense, maybe they don't !  (:)
Logged

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: different tones with same reeds
« Reply #10 on: January 16, 2018, 06:36:13 PM »

All any of us will do is speculate, but there are several variables that affect all the different aspects of sound.  Some don't think wood type and quality affects sound, but I think it does, both in the box construction and reed blocks.  As was mentioned, reed block chambers affect it, and the way most builders make reed blocks, there will always be slight variances in dimensions and angles.  Also, since reeds are at least finished by hand, there are variances there.  And also as mentioned, age plays a big difference in sound.  The volume and response seem to get better with play.  Sometimes the variable stars just line up right.

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: different tones with same reeds
« Reply #11 on: January 16, 2018, 07:06:04 PM »

I always think that reed blocks are very unscientific. The flow of air through the reeds must be so turbulent, due to the shape of the hole in the reed block. Had I the tools, I would love to design a reed block with rounded spaces behind each reed plate. This would smooth the flow of air, and consequently, make a better and more graduated sound' Obviously it would be more expensive to make, which is why mass produced ones are just bog standard, without refinement.
So in effect, my thoughts on the original question are, that differences in the shape of the airbox behind a reed plate, will contribute towards variations in the volume and performance of the reed covering it.

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: different tones with same reeds
« Reply #12 on: January 16, 2018, 07:12:50 PM »

Think "Bose", and think flowing water, flowing exhaust systems. Port and polish.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: different tones with same reeds
« Reply #13 on: January 16, 2018, 07:25:02 PM »

All any of us will do is speculate, but there are several variables that affect all the different aspects of sound.  Some don't think wood type and quality affects sound, but I think it does, both in the box construction and reed blocks.  As was mentioned, reed block chambers affect it, and the way most builders make reed blocks, there will always be slight variances in dimensions and angles.  Also, since reeds are at least finished by hand, there are variances there.  And also as mentioned, age plays a big difference in sound.  The volume and response seem to get better with play.  Sometimes the variable stars just line up right.
As a builder you would have a good idea about what effects the sound, I would think you are right that wood quality and type does effect the sound to a degree. Also the other things you mention.
Question, what woods do you favor for box and also reed block construction? I'm sure you have more than one and that's ok, I'm just curious what your findings are. Probably relates to the reeds being used also. Maybe you could say what combinations you have had good success with.

I always think that reed blocks are very unscientific. The flow of air through the reeds must be so turbulent, due to the shape of the hole in the reed block. Had I the tools, I would love to design a reed block with rounded spaces behind each reed plate. This would smooth the flow of air, and consequently, make a better and more graduated sound' Obviously it would be more expensive to make, which is why mass produced ones are just bog standard, without refinement.
So in effect, my thoughts on the original question are, that differences in the shape of the airbox behind a reed plate, will contribute towards variations in the volume and performance of the reed covering it.

Sir John

I don't see why it would be so difficult to make rounded spaces behind the reed but wonder how much you would gain when the sound/air still has to pass though the sharp edge of the hole in fondo.

Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: different tones with same reeds
« Reply #14 on: January 16, 2018, 07:54:36 PM »

I don't see why it would be so difficult to make rounded spaces behind the reed but wonder how much you would gain when the sound/air still has to pass though the sharp edge of the hole in fondo.

Unless you have a Hohner with round holes in the fondo that is. ;)

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

blafleur

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 530
Re: different tones with same reeds
« Reply #15 on: January 16, 2018, 09:09:43 PM »

I always think that reed blocks are very unscientific. The flow of air through the reeds must be so turbulent, due to the shape of the hole in the reed block. Had I the tools, I would love to design a reed block with rounded spaces behind each reed plate. This would smooth the flow of air, and consequently, make a better and more graduated sound' Obviously it would be more expensive to make, which is why mass produced ones are just bog standard, without refinement.
So in effect, my thoughts on the original question are, that differences in the shape of the airbox behind a reed plate, will contribute towards variations in the volume and performance of the reed covering it.

Sir John

I'm not convinced that better and smoother air flow would necessarily equal better sound.  Can it be that some sounds pleasing to the ear could come from the lack of perfectly smooth air flow?

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: different tones with same reeds
« Reply #16 on: January 16, 2018, 09:17:29 PM »

also the 'smoothness'' or otherwise of the airflow is to a large extent governed by the way the bellows are operated , sometimes to smooth ?lagatoise  a tune or parts thereof or sometimes to add  an additional layer of rhythm  by doing a bit of rumpy tumpy pulsing of the bellows.  etc etc.

george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: different tones with same reeds
« Reply #17 on: January 16, 2018, 09:28:13 PM »

Think "Bose", and think flowing water, flowing exhaust systems. Port and polish.

Yes, I'd see it as relevant in those contexts, but Bose speakers are trying to perfectly reproduce sound that has already been produced without modifying the quality of it, and "flowing exhaust systems. Port and polish" are about improving the performance and efficiency of an engine (though an exhaust system can also have a great sound - I love the "music" my Subaru's flat four produces when I'm driving hard on a windy road, going through the gears and pressing the "growl" pedal to the metal :-[).

But making musical instruments is a whole different ballgame that's all about producing a desireable sound, out of an instrument that's not unduly difficult to play, where the "smoothest" sound might turn out to be the most bland, soulless and characterless. Do we really want to do away with the harmonics that make different boxes sound different, or to encourage them?

I know which I prefer...  ;)

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: different tones with same reeds
« Reply #18 on: January 16, 2018, 10:51:51 PM »

Think "Bose", and think flowing water, flowing exhaust systems. Port and polish.

 , I love the "music" my Subaru's flat four produces when I'm driving hard on a windy road, going through the gears and pressing the "growl" pedal to the metal :-[).

 ;)

at the risk of  being accused (rightly) of gross thread drift I concur fully about the delightful growl of a flat four, having owned several Jowett Javelins and a couple of Jupiters way back. and still being a member of the Jowett Car club , the oldest one make car club in the word!

George   with apologies!
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: different tones with same reeds
« Reply #19 on: January 17, 2018, 10:40:04 AM »

 "think..........flowing exhaust systems. Port and polish."

Just coming to this thread, I certainly did the above. As Triskel wonders about the possible blandness of notes produced, I would point him at the racing engines, they certainly don't produce bland sounds!  Mind you, that doesn't necessarily relate to our instruments.

As for vehicle exhaust notes, I cannot imagine a better one than a TS3* at full revs under load!
(* TS3....Rootes Group 3 cylinder transversely opposed, supercharged, diesel. The twin [mounted in series] exhaust silencers for these were £120 each 40 odd years ago!)
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal