Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Straightening curled leather valves  (Read 7477 times)

0 Members and 1 Guest are viewing this topic.

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Straightening curled leather valves
« on: March 23, 2018, 12:44:51 AM »

First of all I'm only considering the situation when a box was lying flat horizontally. In that case the leathers that face the floor curl down over time. The ones that are on the opposite side are nice and flat.
That is it's not the case when reed valve leathers curle up as a result of aging or excessive playing that leads to valve fatigue.

So suppose that there is a box basically in a new, almost unused condition that was stupidly stored for decades in a horizontal position and the valves facing the floor are all curled.
I've heard that people successfully straightened such curled leathers by first removing them from the reed plates, placing them in water and then drying them up under some weight. (of course for accessing the inner leathers the reed plates are removed from the blocks)

I'm suspicious about that mehtod because the reed valve leathers are made from the same type of fine leather that the best gloves are made of. I don't know how that type of leather is called exactly in English but I know that it's kidskin. It's said to be perhaps one of a few leather types that is absolutely prohibited from moisturizing.

What other agents except from water could be used to facilitate kidskin straightening?

By the way, I was also curious why wetting kidskin would make it stiff and dry. I read that water separates the tanning agents from collagen structure of the leather and as a result it somewhat retuns to its "pre-tanned" state.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Straightening curled leather valves
« Reply #1 on: March 23, 2018, 01:00:42 AM »

Hi Serge,
Welcome!

I'm sure there are a few reasons why the valves curl beyond storage.
I would think if you go to the trouble of trying to straighten them they will fail again sooner than if you replace with new ones leather or vinyl. The latter being what most use nowadays.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Tiposx

  • Durham in England
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 259
Re: Straightening curled leather valves
« Reply #2 on: March 23, 2018, 07:03:22 AM »

I straightened some on a pa using moisture, then a cool iron over tissue paper. They looked straight and flat. A few days later I had to remove them as they curled again.
I also  tried flipping some mildly curved valves over but they didn't seal too well.
Now I only use synthetic valves. I make the largest ones from overhead projector film (acetate ). Noisier than leather but seals well and doesn't curl.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Straightening curled leather valves
« Reply #3 on: March 23, 2018, 07:21:07 AM »

It's not worth trying to straighten curled valves. It's false economy to try. They are unlikely to perform as well and will probably have a limited usable life.
Always replace with new valves, readily available from Charlie Marshall (ships internationally).
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Cag

  • Member
  • *
  • Offline Offline
  • Posts: 44
Re: Straightening curled leather valves
« Reply #4 on: March 23, 2018, 08:23:19 AM »


I've heard that people successfully straightened such curled leathers by first removing them from the reed plates, placing them in water and then drying them up under some weight. (of course for accessing the inner leathers the reed plates are removed from the

 I don't know how that type of leather is called exactly in English but I know that it's kidskin. It's said to be perhaps one of a few leather types that is absolutely prohibited from moisturizing.

What other agents except from water could be used to facilitate kidskin straightening?

By the way, I was also curious why wetting kidskin would make it stiff and dry. I read that water separates the tanning agents from collagen structure of the leather and as a result it somewhat retuns to its "pre-tanned" state.
In English I have seen it called gloving leather but it is also known as Cabretta.

When drying leather you can dictate how stiff it will be by how you treat it as it dries. If you put it in a tumble dryer the fibres will become fluffy and the leather will become very pliant, if pressed it will be thinner, and stiff. The way I heard it this was not a chemical process but a mechanical one.

If you do wet and press thw valve you are likely to replace it at a different stiffness to original and tuning will be necessary.

I'm in the "replace it" corner but have heard of people without replacement stock taking valves off and rolling them backwards and then refitting. I suspect relief will only be temporary.
Logged

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Straightening curled leather valves
« Reply #5 on: March 23, 2018, 03:32:08 PM »

It's not worth trying to straighten curled valves. It's false economy to try. They are unlikely to perform as well and will probably have a limited usable life.
Always replace with new valves, readily available from Charlie Marshall (ships internationally).

Steve - I'm sure you know what you are talking about and thanks for the link to the Charlie Marshall's online store.
Could you help me with a related question please?

Suppose I want to replace my old leather valves with a new set of vinyl/mylar/etc. "new style" valves. How are they gauged compared to the "old style" leather valves?
I see reputable sellers (such as Charlie) have these "plastic" valves in different sizes. Do they gauge the valve's elasticity/rigidity/etc. according to the corresponding reed sizes? In other words when transitioning from leather valves to vinyl valves do I only need to take into account the original leather valve size and replace it with the equal size vinyl valve?
Suppose I have a 30 mm x 6 mm leather valve that needs replacement. Do I get the equal size vinil/etc. valve?

Can I expect approximately the same response/volume/etc. from the reed that is general playing characteristics after making such a transition?

Another question is - are there normally any changes in the amount of glued area when comparing the 2 valve styles? What I mean is this: suppose you see that the base of a leather valve glued area is somewhat like 8 mm. Do I normally use the same amount of glue for vinyl valves?
By the way - what glue won't destroy the plastic valves?

Of course we can't avoid re-tuning after changing the valves especially when making such obvious changes as transitioning from one valve type to another. Our task is however is to minimize the overall transition effect so we re-tune as little as possible. Hence all my questions above.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Straightening curled leather valves
« Reply #6 on: March 23, 2018, 05:53:47 PM »

All you need to do is buy the lengths of valves that you need. Vinyl or leather are broadly interchangeable.
The vinyl valves generally are already fitted with extra leaves which act as stiffening springs. The large leather valves (say 35 mm or more) really need additional stiffening steel springs and 'dots' (as on this page).

You can also buy synthetic leather 'vileda' valves instead of the longer real leather valves. The vileda valves usually have additional vinyl leaves instead of requiring springs and dots. There are mixed feelings about vileda valves, mainly concerns that they may harden with age. But I have had some in use for over 10 years and they are still working fine.

The length of the glued area is much the same for leather and vinyl valves, so approx 5 mm - 8 mm, depending on the overall length of the valve.

Vinyl valves tend to be noisier than leather valves, mainly on the bellows direction changes; the larger vinyl valves tend to be a bit 'raspy'. A good compromise is to have leather or vileda valves for the lower-pitched reeds - say 30 mm or longer with vinyl valves for the smaller sizes. Overall, vinyl valves absorb fewer higher frequencies compared with leather, so the sound tends to be just that little bit brighter. But most listeners would not be able to tell the difference.

Glue: solvent free contact glue is fine for leather, vileda and vinyl valves. Or you can use the special valve adhesive. But I've always used the contact adhesive with perfectly acceptable results.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Straightening curled leather valves
« Reply #7 on: March 23, 2018, 06:25:36 PM »

Thank you Steve - That's all I wanted to know.
However, believe me or not I hear about the "solven-free contact glue" for the first time! Actually it would be nice to have such an adhesive for glueing any plastic parts but I'm yet to find it. Do they really exist? I'm not kidding, I'm just a little confused.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Straightening curled leather valves
« Reply #8 on: March 23, 2018, 06:46:42 PM »

Thank you Steve - That's all I wanted to know.
However, believe me or not I hear about the "solven-free contact glue" for the first time! Actually it would be nice to have such an adhesive for glueing any plastic parts but I'm yet to find it. Do they really exist? I'm not kidding, I'm just a little confused.
This is the stuff:
https://www.amazon.co.uk/Bostik-Purpose-Solvent-Free-Adhesive/dp/B0001OZI5W
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Straightening curled leather valves
« Reply #9 on: March 23, 2018, 07:16:10 PM »

Thank you Steve! You have opened my eyes. Amazon also shows other brands of solvent-free glues and I know that UHU for instance was available locally. wUHU!  (:)
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Straightening curled leather valves
« Reply #10 on: March 23, 2018, 08:15:16 PM »

I can confirm Steve's choice of glue for the valves. It's the best I've found.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Straightening curled leather valves
« Reply #11 on: March 23, 2018, 10:12:40 PM »

"https://www.amazon.co.uk/Bostik-Purpose-Solvent-Free-Adhesive/dp/B0001OZI5W"

The message I get is -     No sellers are currently delivering this item to  . .   "my country"! 


Sooooooo . . . . .
What type of glue is it?

PVA
PVAc
Superglue
other

And what means  wUHU ? 
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Straightening curled leather valves
« Reply #12 on: March 23, 2018, 10:15:59 PM »

It's a contact adhesive. When gluing valves it's best left for 10 - 15 minutes before attaching the valve to the reed plate.
I get mine from eBay, probably available in your country.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Straightening curled leather valves
« Reply #13 on: March 23, 2018, 10:34:40 PM »

OK,   why I   ask   is . . . . .


Do you need  valves?   Really?

They do not seem to be necessary when playing harmonica.

I bought an East German big game a few days ago.   28 pounds.    In original cardboard. Did not look used.
Some tones sounded subdued.   When I opened it, everyone fell out, ALL valves,  -  like dead flies.
   Now it sounds a lot better.    (:)    Therefore, I wonder if I will put them back in.


  The valves seem quite OK,   but not the glue.   So  what kind/type of glue? 

"Contact glue"  in my country  smell,  so there must be some sort of   solvent.

« Last Edit: March 23, 2018, 10:36:42 PM by Stockaryd »
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

Serge

  • Member
  • *
  • Offline Offline
  • Posts: 21
Re: Straightening curled leather valves
« Reply #14 on: March 23, 2018, 10:39:19 PM »

...
And what means  wUHU ?

Something like Woo-Hoo?
(re-spelled popular exclamation)
No? - Sorry :(
( ;))
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Straightening curled leather valves
« Reply #15 on: March 23, 2018, 10:52:34 PM »

Do you need  valves?   Really?


Short answer yes , except for the high reeds.

Air loss and I believe it will alter the pitch.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Straightening curled leather valves
« Reply #16 on: March 23, 2018, 11:51:16 PM »

...
And what means  wUHU ?

Something like Woo-Hoo?
(re-spelled popular exclamation)
No? - Sorry :(
( ;))



(:)     Sorry   It is so hard to understand all the jokes in a  "strange"    language.   (and if I try to make a joke it's even worse)

  And UHU  exists in my country,  but you can not understand what it is in it.   No declaration.   

Can I use   Hide glue on the valves and how long will  that last?

  Contact glue/adhesive  is almost everything called here.  Gives me no clue.   (. .  and this was a try )
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Straightening curled leather valves
« Reply #18 on: March 24, 2018, 10:17:30 AM »

Apparently you can use this gasket shellac. I've never tried it...has anyone on here tried it?
https://www.amazon.co.uk/Gasket-Shellac-Sealant-DISPATCH-VC52000/dp/B014LCY8ZK

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Straightening curled leather valves
« Reply #19 on: March 24, 2018, 10:38:56 AM »

Looking at that bottle brings back memories of tins of that horrid stuff, Stag Jointing Compound, which could also quite possibly do the job too. Best off sticking with an easy to use modern alternative, methinks.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal