Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Bent Grill  (Read 2040 times)

0 Members and 1 Guest are viewing this topic.

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Bent Grill
« on: October 22, 2018, 10:15:12 AM »

Any ideas on how to straighten this grill without creasing it or damaging it? I've applied hand pressure, to no avail Do not want to ruin it.
Logged
Hohner Club IIB Victoria

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Bent Grill
« Reply #1 on: October 22, 2018, 12:56:03 PM »

Try this:
Remove the grille and place it, inside downwards, on a soft cloth or blanket. Place another cloth on top and then use a cook's rolling pin gently back and forth over the top of the grille, rolling from the centre towards the ends. Try to avoid rolling and flattening over the cut-out lip in the middle, nor use such force that you flatten the raised rim or the edges. But repeated gentle rolling should hopefully start to change the convex shape to flat.

Anyone else have a better idea?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Bent Grill
« Reply #2 on: October 22, 2018, 01:12:19 PM »

Have you used that method successfully Steve?

I don't think it would work on a Hohner grill, because the central areal of the grill is slightly raised when in good condition.  When I've had grills with this sort of bend to repair I've combined  two approaches, usually with partial or complete success. 

The first is to look for any dents, or depressed patches in the main part of the grill and straighten them.   For broad hollows gently push them out with the thumbs while supporting surrounding areas.  For smaller localised bends in the main part place the grill outside surface down on a smooth hard surface and use a light hammer on any bits that are raised up on the inside (which is now uppermost).   This should get you to the point where the main area of the grill is now free of dents or undulations.

Now if that has not cured the bend go to the second step.  This is to work on the lip of metal that is folded over at right angles along the edges.  Often this lip gets distorted and if it is bent away from a right angle either inwards or outwards it will produce the type of bend show in your photo.  If you can see this use a pair of wide nosed pliers to gently bend it back.  You will have to do this gradually working along the bent area.  This should remove some of the bend, or if you are lucky, all of it.   If there is still some bend then place the grill across your thigh and, holding the bent edge gently press down on either side of the bend.   Keep doing this and checking and repeating the process until the bend is gone.  The key to this is that the bent over edge gives stiffness to the piece so that is where you must direct your straightening efforts.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Bent Grill
« Reply #3 on: October 22, 2018, 01:38:20 PM »

I had this problem with one of my old things, the grille had several dents in it, and was curved and wavy. After knocking and pressing out the actual dents, the curve and wave was even more noticable!
Eventually I made a press from two bits of plywood, one which fitted inside the inner rectangle, the part of the grille which stands proud, and another, like a frame, which fitted on the flat outer part, with a bit of leeway in between.
It was then just a matter of squeezing the two together, which slightly elongated the "walls" of the risen centre piece, thus taking up the "stretchedness" from the whole and returning it to more or less the original shape. 
The squeezing was managed by placing the grille upside down, into the frame and then placing the rectangular bit inside that and attacking it with a hammer. It was most satisfying!!! I cannot now recall the thickness of the ply, I think about 3/8, or possibly a bit thinner. Anyway, it worked.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Bent Grill
« Reply #4 on: October 22, 2018, 01:54:27 PM »

Have you used that method successfully Steve?
Yes, but it was on the sheet metal decking of a model boat, not a Hohner grille, which is why I was a bit cautious in my reply.
I agree with your methodology especially where the long edge lip gets distorted, and on a real Hohner grille, I have used round nosed pliers to try to flatten out any obvious kinks. But I have found there can be an overall residual set where the stresses need to be redistributed and I think rolling over the angle where the face and long edge lip might be one way of doing this. So long as it is done carefully and gently, it won't do any harm and may well work quite nicely, like it did on the model boat.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Bent Grill
« Reply #5 on: October 22, 2018, 09:21:37 PM »

I've had to straighten loads like this....I just use these 🤲 works every time 😉

Martyn
« Last Edit: October 22, 2018, 10:54:07 PM by Martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Bent Grill
« Reply #6 on: October 22, 2018, 09:24:42 PM »

Want!
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Bent Grill
« Reply #7 on: October 22, 2018, 09:40:45 PM »

What you need is a steam driven rolling mill

https://www.youtube.com/watch?v=6HVumgMe4gg

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Bent Grill
« Reply #8 on: October 22, 2018, 10:05:54 PM »

What you need is a steam driven rolling mill

That would do the trick Lester!

https://www.youtube.com/watch?v=6HVumgMe4gg
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Bent Grill
« Reply #9 on: October 22, 2018, 11:13:26 PM »

Martyn, What is it that you use that works every time? I don't see anything.
It looks like fists in boxing gloves to me!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Bent Grill
« Reply #10 on: October 22, 2018, 11:19:10 PM »

What you need is a steam driven rolling mill

https://www.youtube.com/watch?v=6HVumgMe4gg
Thanks Lester!
I've watched this engine working many times. It is very impressive and rather scary to see it run from full speed in one direction to be suddenly reversed and back up to full speed in the other direction (as is needed for a rolling mill). Several tons of steel have to be rapidly brought to a standstill and then accelerated again. The whole building shakes!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Martyn

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 455
  • Hohnerohner
    • Martyn White Melodeon Tuning and Repairs
Re: Bent Grill
« Reply #11 on: October 23, 2018, 09:03:47 AM »

Martyn, What is it that you use that works every time? I don't see anything.
It looks like fists in boxing gloves to me!

It was hands. With a bit of gentle bending it the right places you can straighten any metal grille.

Martyn
« Last Edit: October 23, 2018, 09:35:10 AM by Martyn »
Logged
'Anything from a small repair to a full restoration'.
www.melodeonrepairs.co.uk

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Bent Grill
« Reply #12 on: October 24, 2018, 10:13:50 AM »

Success!  Years ago I read a book about sheet metal work which discussed shrinking and stretching metal. This came to mind yesterday so I took a hammer, placed it face up,on my bench...placed the curved lip of the long side of the grill on the hammer face....then tapped ever so lightly with a smaller hammer where the piece was most curved.  In less than a minute the grill was nice and straight.  Stretching the metal worked wonderfully and this was the first time doing this technique.  Thanks to all for the input.
« Last Edit: October 24, 2018, 10:37:44 AM by Barry Tolson »
Logged
Hohner Club IIB Victoria

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Bent Grill
« Reply #13 on: October 24, 2018, 10:48:05 AM »

A touch more "finnese" than bashing my plywood former, then? Well done that man!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Bent Grill
« Reply #14 on: October 24, 2018, 02:04:57 PM »

Mr. Smith...Thanks!  I do tend to take the most conservative approach!.
Logged
Hohner Club IIB Victoria
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal