Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Prepping  (Read 3998 times)

0 Members and 1 Guest are viewing this topic.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Prepping
« on: October 28, 2018, 04:37:40 PM »

I can already see the eyerolls as the new guy starts another thread. Oh well, it is my most used emoli.

While I wait for parts and try to figure out what I'm doing, it occurred to me that there is no reason to be idle and loose steam. The plates need to be stripped from the blocks and kept in order. Are they marked or should it be obvious? I did a bit of a search but couldn't really find what I was after. Lots of info on rewaxing. Also new valves since I'll be ordering them today. leather or plastic?  ::) Up next will be new felt on the paddles (pretty sure that's the wrong word) I see pre-cut kits for sale but cutting individual bits doesn't seem that bad. I assume they want special glue as well?

Thanks in advance
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Prepping
« Reply #1 on: October 28, 2018, 04:47:24 PM »

I have a number of sandwich trays in the workshop. When stripping reed bocks I start with the block oriented tallest on left shortest on right and strip those reeds off laying them on the tray, in order, on the side nearest me, then I flip the block and strip to other side laying them to match the first set on the side furthest me.


If it's a Hohner block nearly alway the first set of reeds striped will be the set tuned to pitch and the other set the sharp set.

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Prepping
« Reply #2 on: October 28, 2018, 04:54:03 PM »

I have a habit of dropping things in my dingey hovel, so, when I take the reeds off the block, I shove them onto a magnetic strip (by the rivets) and in order. I can still drop them, of course, but not all together and get them mixed up. Mind you, they increase/decrease in size as they go, so it shouldn't really be a problem anyway.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #3 on: October 28, 2018, 04:55:08 PM »

I have a number of sandwich trays in the workshop. When stripping reed bocks I start with the block oriented tallest on left shortest on right and strip those reeds off laying them on the tray, in order, on the side nearest me, then I flip the block and strip to other side laying them to match the first set on the side furthest me.


If it's a Hohner block nearly alway the first set of reeds striped will be the set tuned to pitch and the other set the sharp set.

What are using to clean off the old wax from the plates and blocks?
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Prepping
« Reply #4 on: October 28, 2018, 05:04:21 PM »

I mark an X on the block above the biggest reed on one side, and a O above the corresponding reed on the other side. I then strip them all down keeping the reeds in order.
Things to watch, often a couple of the reeds on each side will be mounted the opposite way up to all the others. Keep them that way when rebuilding. Don't scrape old wax off with a sharp blade, use something like the blunt side of a craft knife blade, and then clean the remaining wax residue off with a small softish wire brush. The blunt edge avoids taking chunks out of the wood, which is usually pine, not a very hard wood.
It's easier to buy sheets of pallet facing felt, and cut your own, remember that it comes in different thicknesses, and getting the right thickness matters.
There will be more tips coming your way no doubt, but keep asking that's how I learned.

Sir John
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #5 on: October 28, 2018, 05:20:41 PM »

I mark an X on the block above the biggest reed on one side, and a O above the corresponding reed on the other side. I then strip them all down keeping the reeds in order.
Things to watch, often a couple of the reeds on each side will be mounted the opposite way up to all the others. Keep them that way when rebuilding. Don't scrape old wax off with a sharp blade, use something like the blunt side of a craft knife blade, and then clean the remaining wax residue off with a small softish wire brush. The blunt edge avoids taking chunks out of the wood, which is usually pine, not a very hard wood.
It's easier to buy sheets of pallet facing felt, and cut your own, remember that it comes in different thicknesses, and getting the right thickness matters.
There will be more tips coming your way no doubt, but keep asking that's how I learned.

Sir John

Pallet!! That was the word I was searching for. Good point on the felt thickness. I actually thought it would be standard. Silly me. Any thoughts what thickness I may need?

Also, How the heck to you get the old bass buttons off? They seem pretty fused to the stem. (I know, not a stem)
Logged

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Prepping
« Reply #6 on: October 28, 2018, 05:40:37 PM »

Modest heat, e.g. from a soldering iron, close to the button and a pull.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Prepping
« Reply #7 on: October 28, 2018, 05:44:39 PM »

I have a number of sandwich trays in the workshop. When stripping reed bocks I start with the block oriented tallest on left shortest on right and strip those reeds off laying them on the tray, in order, on the side nearest me, then I flip the block and strip to other side laying them to match the first set on the side furthest me.


If it's a Hohner block nearly alway the first set of reeds striped will be the set tuned to pitch and the other set the sharp set.

What are using to clean off the old wax from the plates and blocks?


Once the reeds are popped off I use the back of a scalpel (any other blunt blade will do) to scrape both the reed plates and the blocks to remove the bulk of the old wax. I then have a brass bristled brush which I clean everything with.

Always wear a dust mask when doing this old wax dust is horrid if breathed in.

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #8 on: October 28, 2018, 05:54:51 PM »

I have a number of sandwich trays in the workshop. When stripping reed bocks I start with the block oriented tallest on left shortest on right and strip those reeds off laying them on the tray, in order, on the side nearest me, then I flip the block and strip to other side laying them to match the first set on the side furthest me.


If it's a Hohner block nearly alway the first set of reeds striped will be the set tuned to pitch and the other set the sharp set.

Good point on the dust mask. I also really like Edward's idea with the magnetic strip to keep things in order.

What are using to clean off the old wax from the plates and blocks?


Once the reeds are popped off I use the back of a scalpel (any other blunt blade will do) to scrape both the reed plates and the blocks to remove the bulk of the old wax. I then have a brass bristled brush which I clean everything with.

Always wear a dust mask when doing this old wax dust is horrid if breathed in.
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #9 on: October 31, 2018, 08:07:40 PM »

Alright, wax, valves and felt are on their way. I also found some 1" magnetic strips that I can stick to my tray after cleaning the plates. I've been doing a small amount of reading on tuning and I have to admit that it seems a bit daunting. Is there a simple DIY tuning method that doesn't involve building a bench?
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Prepping
« Reply #10 on: October 31, 2018, 08:26:59 PM »

All you need is something to hold your instrument so that the bellows can be opened and closed with one hand, using the other to hold the end that you're working on on the other end to test each reed as you open the pallet. You'll also need to tape off the opposite reed whilst tuning each one. It's slow and laborious but simple and effective.
A "U" shaped device made from a couple of bits of scrap wood does me. I clamp it onto my Workmate, and Bob's my Uncle, he could be your's too!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #11 on: November 02, 2018, 06:48:26 PM »

We have an interloper!! I got all of my reed plates and blocks cleaned up last night and they came out quite nice. Leather valves pretty much all fell off. There is one reed plate that is not like the others as shown with my pointer. It is aluminum, not zinc and the reed is not tapered like the rest. There is half of a stamping but I can't make it out. Should I leave it and wait until tuning time to see if it sounds right or see if there is a correct "H" plate in my parts CF box to sub in?

IMG_8518 by Pat McInnis, on Flickr
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Prepping
« Reply #12 on: November 02, 2018, 07:41:25 PM »

It looks like a mis-stamp of the circle on the old Dix reeds which are in my oldest Hohner 1 row and my International 1 row.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #13 on: November 02, 2018, 08:58:49 PM »

It looks like a mis-stamp of the circle on the old Dix reeds which are in my oldest Hohner 1 row and my International 1 row.

Quality is low. Seems almost homemade.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Prepping
« Reply #14 on: November 02, 2018, 09:29:02 PM »

... Should I leave it and wait until tuning time to see if it sounds right or see if there is a correct "H" plate in my parts CF box to sub in?

If this is an A/D reed set, the "interloper" should be E/F#, in which case you don't have an exact match in
your C/F box.
But you do have an E/F, which is the 4th reed from the bottom on the outside row.
You can tune the F to F#.
Personally, I wouldn't do that for now. The "interloper" might turn out to be fine.
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #15 on: November 02, 2018, 09:35:05 PM »

... Should I leave it and wait until tuning time to see if it sounds right or see if there is a correct "H" plate in my parts CF box to sub in?

If this is an A/D reed set, the "interloper" should be E/F#, in which case you don't have an exact match in
your C/F box.
But you do have an E/F, which is the 4th reed from the bottom on the outside row.
You can tune the F to F#.
Personally, I wouldn't do that for now. The "interloper" might turn out to be fine.

Good call. Get it together before I get all fancy.
Logged

Rob2Hook

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2278
  • Castagnaris, Hohners & Baffetti
Re: Prepping
« Reply #16 on: November 07, 2018, 01:00:03 PM »

The only waxing I have done was on a Preciosa - talk about starting the hard way.  Still, it could have been worse, could have been a four-stop!

I found getting the old wax scraped away was fairly easy with a steel 6" rule.  The end went nicely around the individual plates and the long edge scraped the blocks.

Rob.
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Prepping
« Reply #17 on: November 07, 2018, 03:00:28 PM »

The only waxing I have done was on a Preciosa - talk about starting the hard way.  Still, it could have been worse, could have been a four-stop!

I found getting the old wax scraped away was fairly easy with a steel 6" rule.  The end went nicely around the individual plates and the long edge scraped the blocks.

Rob.

Nice, mine came out really clean and I used a broken car door trim removal too (don't ask) for scraping since it had a comfortable handle and wasn't too sharp. Then I finished them with a brass brush. Of all the different waxing methods, it looks like the old tiny paint brush appears to be the easiest but I won't know until I start.

Maybe a small dab of wax to hold them in place to get started? Also, is it just a contact cement for the valves? I'm using synthetic not leather.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Prepping
« Reply #18 on: November 07, 2018, 03:54:25 PM »

The only waxing I have done was on a Preciosa - talk about starting the hard way.  Still, it could have been worse, could have been a four-stop!

I found getting the old wax scraped away was fairly easy with a steel 6" rule.  The end went nicely around the individual plates and the long edge scraped the blocks.

Rob.

Nice, mine came out really clean and I used a broken car door trim removal too (don't ask) for scraping since it had a comfortable handle and wasn't too sharp. Then I finished them with a brass brush. Of all the different waxing methods, it looks like the old tiny paint brush appears to be the easiest but I won't know until I start.

(1) Maybe a small dab of wax to hold them in place to get started? (2) Also, is it just a contact cement for the valves? I'm using synthetic not leather.

(1) Yes, that's a good idea, especially when new to the job. It also enables you to check whether the valves are working properly before doing all the complete waxing. There is usually not a lot of clearance inside the reed chamber and it is all too easy to have a valve fouling the sides or end of the reed chamber. (remedies: reposition the reed plate a fraction or the valve; trim the valve length if it is too long; or final resort, carve some of the wood away from the reed chamber end.

(2) Sovent-free contact adhesive is good (e.g. Bostik). Just put a smear of adhesive evenly on the valve and immediately press into place on the reed plate. No need to put additional adhesive on the reed plate. The length of valve to apply adhesive to varies but approx 1/4 to 1/5 of the valve length is usually about right. 
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Prepping
« Reply #19 on: November 07, 2018, 08:37:32 PM »

... There is usually not a lot of clearance inside the reed chamber and it is all too easy to have a valve fouling the sides or end of the reed chamber. (remedies: reposition the reed plate a fraction or the valve; trim the valve length if it is too long; or final resort, carve some of the wood away from the reed chamber end.

It will not be necessary to remove any wood from the chamber in order to fit a new valve.
This measure is only called for when fitting a reed that is longer or wider than the original.
I am a bit surprised at your advice.

Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal