Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: Instrument mic(s)  (Read 7369 times)

0 Members and 2 Guests are viewing this topic.

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Instrument mic(s)
« Reply #20 on: December 02, 2018, 09:42:43 AM »

As you may have seen in my recent TotM post, I have borrowed the band's apparently aged and in need of a clean M310:




I connected the two devices to my audio interface simultaneously. However: If I used a 1/4" jack plug input for the Microvox, I could not receive any discernible input from it. If I used a XLR adapter, I then was able to do so, however this means obviously I had to turn off Phantom Power. I'm pretty sure I've had this work with a 1/4" cable on our mixer so maybe there's something I'm doing wrong here (for example, I only have TRS cables and no TS cables, so perhaps this is upsetting it somehow). To even things out, I'd intended to use XLR for the Myers, but this moved it to not receiving any input with my interface. Both devices work with our regular mixer via both input vectors, so, I'm sure there's something to the wiring...

So: I had to use XLR and a significantly higher gain to obtain input from the Microvox M310, and as you can see, it does not even remotely fit on the dino, but, that's fine, this is an accordion pickup, and this is exactly why they made the 4## series available in a variety of sizes. I assume the difference in their output levels can be attributed to the size of the electret mic capsule (microvox's are larger) and that it uses an 1.5v AA battery rather than a 3v coin cell. I positioned it such that 2 of its 3 capsules line up with roughly where the myers' are.

I'll present some audio of them both here probably later today, because there's some weird noise on one of the tracks from Adieu that I want to verify as unusual, but, honestly my gut feeling is that the quality of the audio is roughly the same from both, once you account for the gain differences. Obviously you'll have the opportunity to decide for yourself.
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Instrument mic(s)
« Reply #21 on: December 02, 2018, 12:17:21 PM »

Microvox pick ups have mic level outputs, not line, and need microphone pre-amps. I currently use a fairly new 310 with a combined bass and treble output. The microphone input in my personal PA is sufficient and works fine for me.

However,  if you only have one mic input  and your pick has seperate bass and treble outputs you're left with only one side getting sufficient boost.  I use a Behringer 1002B mixer,  on battery power, on my old pickup, with separate bass/treble outputs, to provide gain stages for both channels and some  EQ.  Works a treat. Sits nicely on top of my amp. With plenty of spare inputs, it also gives me a capability to take other band instruments through my PA when required, which is a useful bonus (cost less than £80, including delivery, from Gear 4 Music).

You do have to be careful to make sure phantom power is off if the pickup is not isolated from it. Microvox recommend a Behringer D120 DI box (costs less than £20 if you shop around). I use one of these,  but Santa is bringing me an Xvive wireless link, which will have the same effect.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Instrument mic(s)
« Reply #22 on: December 02, 2018, 01:16:12 PM »

I personally am very happy with my Audio-Technica ATM350. The sound is really great (and doesn't miss anything on the bass side), and I've rarely had issues like feedback loops and such on stage.
The clips are quite manageable so that you can switch easily enough. I clip them on the bellows strap for the right-hand side and on the bass strap for the left-hand side. (Most often than not when I'm switching accordions on stage, I end-up with a stand microphone (ribbons mikes are great) and a clip-on mike on the left-hand side for each of the accordions.)
The cons is that they can be a bit more expensive than other mikes, like the aforementioned C516, but IMHO the sound quality with ATM350 is far superior.

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Instrument mic(s)
« Reply #23 on: December 02, 2018, 01:52:42 PM »

Microvox pick ups have mic level outputs, not line, and need microphone pre-amps.

Yes, that's right. I should clarify though, my audio interface helpfully does have an instrument level / line level switch for each input, which does allow it to work quite happily with lower voltage input signals, but, not this low, plus I don't know that this helps any with the impedance mismatches, which can be a pretty big factor in how decent your pickup ends up sounding and a big mismatch would bury your signal level even lower, which is what I think is happening here to the m310. If someone out there is looking at these two systems side by side, I do not need to use an XLR mic input for the Myers, which given I don't have a way to isolate phantom power per input on any of the systems I'm using right now, could be a pretty big benefit if I need to use my condenser mic (which needs the 48v). At some point though I imagine I'll buy a DI box and that issue will be rather moot.

Anyway, I managed to get both devices working through XLR - the answer there was a temperamental adapter. These recordings of a Black Pearl 2, with any/all bass reeds firing.

Myers Grip Plus 6" w/Bass Extension:
https://soundcloud.com/user-889775496/melodeon-myers-test
Microvox M310:
https://soundcloud.com/user-889775496/melodeon-microvox-test

(Tunes are Theme Vannetaise, Speed the Plough, and My Love She's But a Lassie Yet)

However, you probably don't need to listen back and forth between these, I can tell you that if I hadn't written on them which one was which, there's basically no way to really tell them apart, at least that I can really notice - the Microvox has slightly more of the bass coming through but mic position wold adjust that. Bottom line is, an array of electret microphones placed near your melodeon like this is only ever going to sound so-so, whatever you do, but neither system seems to give worse acoustic results than the other, so, if you're shopping for a one stop solution, maybe check these out and get whichever setup fits your instrument better, or deals with your input issues the most conveniently.

Disclaimer: this post is pretty much the gold nugget of information that past-me would have latched on to to help figure out what the heck I should do about getting a pickup, which is why I've gone to the effort of doing all this, even though I think Roger has his answer. I have generally found a lot of opinion and not really enough examples, so, I'm hoping to address that balance.
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Instrument mic(s)
« Reply #24 on: December 02, 2018, 05:18:59 PM »

Microvox pick ups have mic level outputs, not line, and need microphone pre-amps.

... my audio interface helpfully does have an instrument level / line level switch for each input, which does allow it to work quite happily with lower voltage input signals, but, not this low, plus I don't know that this helps any with the impedance mismatches... At some point though I imagine I'll buy a DI box and that issue will be rather moot...

Not sure what's going on there, Gena. All three of my units (one bass, one treble and one combined) work as well as would expect, and as well as each other,  going into the very bog standard mic amps that the Behringer Xenyx features or directly into the mic input on my PA. That's to say, I am happy to recommend them for dance outs and the like, but it wouldn't  be my go to for studio work. Maybe your 310 is faulty.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Instrument mic(s)
« Reply #25 on: December 02, 2018, 07:04:52 PM »

Microvox pick ups have mic level outputs, not line, and need microphone pre-amps.

... my audio interface helpfully does have an instrument level / line level switch for each input, which does allow it to work quite happily with lower voltage input signals, but, not this low, plus I don't know that this helps any with the impedance mismatches... At some point though I imagine I'll buy a DI box and that issue will be rather moot...

Not sure what's going on there, Gena. All three of my units (one bass, one treble and one combined) work as well as would expect, and as well as each other,  going into the very bog standard mic amps that the Behringer Xenyx features or directly into the mic input on my PA. That's to say, I am happy to recommend them for dance outs and the like, but it wouldn't  be my go to for studio work. Maybe your 310 is faulty.

My experience corresponds exactly with Greg's; never had any problem at all running my Microvoxes (Microvoces?) directly into a variety of standard mixing desks in all sorts of PA set-ups.  And like Greg, I'm perfectly happy with them live on stage, but wouldn't use them for recording except as a very last resort. Sounds like something isn't quite right somewhere.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Instrument mic(s)
« Reply #26 on: December 02, 2018, 07:46:42 PM »

Sorry, I'll try to clarify: I was trying to describe the options I had to avoid using a mic level XLR input, if I had wanted to. They both work fine on XLR, as you can obviously hear from the recordings supplied. What I was trying to allude to is that, there can be more options than just Mic Level and Line level. I can only relay my experience with this piece of equipment, but it falls almost entirely inline with what Greg said - that the M310 requires a mic level preamp, which does appear to be the case. However, "needs mic level" doesn't necessarily mean the same thing as "not Line level":

With the Audio Interface I'm using, a UMC404HD, there are the Mic level, low impedance XLR inputs. There are also 1/4" high impedance inputs, which have switches which you can use depending on if you're putting Line level or Instrument level signals into them (which are lower voltage). There's also a Pad switch which is the opposite, it applies less amplification for particularly hot higher voltage signals. Some mixers have similar options, but basically these seem to boil down to a flat additional amplification/attenuation. Some of these features do seem to be available elsewhere, so I don't think they're unique to this interface or product range.

Running the Myers into a 1/4" input set to expect Instrument level provides a perfectly viable signal that I can easily get to clip. Running the M310 into a 1/4" input expecting Instrument level seemingly does not and barely registers even at max gain. Running both into XLR does not provide such a stark contrast in their output levels so I mused that perhaps impedance mismatch was causing a significant drop off in the microvox's output, but that realistically the only reason one wouldn't plug into XLR is if you don't have a DI box to avoid phantom power. After all, they're both self powered, and both use electret microphone capsules, so, I was trying to provide meaningful information on their differences with all the resources I have available to me. For example, this information would be very meaningful to me, if I didn't already know it.

However, you both have extensive experience with the M310: I can only see through the lens of what I thought I'd described, so, I dunno, can you explain the issue you thought I was experiencing? Has your experience always been with using the M310 via XLR mic level inputs, or has it included plugging into any 1/4" jacks.
Logged

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Instrument mic(s)
« Reply #27 on: December 02, 2018, 09:41:08 PM »

It's not going to be an impedance mismatch problem.
An electret based system like the Microvox has a source impedance of about 1k; a mic input (XLR) is typically 2-3k and a line input is typically 10k; and an instrument input might be 100k - 1M. All of there are perfectly compatible. Impedances don't need to be equal. A low source impedance feeding a higher load impedance is normal these days (it might not have been in the 1950s...). A high impedance source like an electric guitar will have problems with a low impedance amplifier input, and that will show up as tonal problems, like no bass end in the sound. So called 'instrument' inputs are for electric guitars, basically, and with the sensitivity to match. They will work with other sources as long as there's enough signal.

Quote
I connected the two devices to my audio interface simultaneously. However: If I used a 1/4" jack plug input for the Microvox, I could not receive any discernible input from it. If I used a XLR adapter, I then was able to do so, however this means obviously I had to turn off Phantom Power. I'm pretty sure I've had this work with a 1/4" cable on our mixer so maybe there's something I'm doing wrong here (for example, I only have TRS cables and no TS cables, so perhaps this is upsetting it somehow).
That might be much nearer the mark. Some Microvox battery boxes switch on when you insert the jack plug. This relies on a TS plug shorting R and S contacts in the box to complete the battery circuit. (since you've used these abbreviations, I assume you know what they mean*) If it's one of those, you have to use a TS-TS cable

I have made several battery boxes for Microvox kit which:
  • have an  XLR output
  • Don't care if phantom power is on or off
  • Push-to-test button connected to LED (doesn't waste battery power, an always-on LED takes more current than the mic )
  • One of them has a soft switchon as the power switch is combined with a volume control
Very useful. I sometimes wonder if I should be making them for others...

-------------------------------
*for anyone who didn't know:
T - Tip
R - Ring
S - Sleeve
Hence
TS = usual 'mono' jack plug
TRS = 'stereo' plug as used on headphones, but also for balanced lines in pro audio equipment where there isn't space for XLRs.

Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Instrument mic(s)
« Reply #28 on: December 02, 2018, 09:42:59 PM »


However, you both have extensive experience with the M310: I can only see through the lens of what I thought I'd described, so, I dunno, can you explain the issue you thought I was experiencing? Has your experience always been with using the M310 via XLR mic level inputs, or has it included plugging into any 1/4" jacks.

Speaking for myself, I interpreted your original post as a ...concern...that, of the two units you were using, one worked ok with your kit, the other one  didn't.

I was pointing out that my newish 310 and older 310s both work fine if you use them according to their design parameters. That is to say, if you feed them into microphone inputs. They are, after all, microphones.

The difference you perceive in the outputs could, well, be the result of the fact that the two pickups are actually very  simple arrays of very well matched microphone capsules, selected for this application. If you present microphones in parallel this reduces the output impedance of the array. If you are feeding this into a Hi Z guitar pickup input this may be the source of the impedance mismatch you are worried about.

The suitability of an input does not depend on the type of plug used to input the signal. I have both XLR and 1/4 jack inputs on my kit and use both depending on the setup  I am using. That is to say, I use a 1/4" jack to 1/4" jack lead direct into my microphone input on my PA. If I am using my mixer to patch in other musicians it has only got XLR inputs for the mic pre-amps.

This little article is a simple answer to the basic question you are asking, albeit, in reverse  (:) (it's asking why guitars don't work right in lower impedance inputs, but it touches on why feeding into a mic pre-amp works better for low impedance devices. The magazine it comes from, Sound On Sound, is very highly recommended).

https://www.soundonsound.com/sound-advice/q-what-are-correct-input-impedances-guitars-and-mics

What I would say is, why use a device in anything but an optimum way, if using it right is easy, and relatively cheap?

[Edit: I cross posted with Anahata and what he says is right and  more informative and more concise than me, but I think my final point still stands, so I'll leave it.]
« Last Edit: December 02, 2018, 09:51:50 PM by Tone Dumb Greg »
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Instrument mic(s)
« Reply #29 on: December 02, 2018, 11:38:22 PM »

Speaking for myself, I interpreted your original post as a ...concern...that, of the two units you were using, one worked ok with your kit, the other one  didn't.

Ah, right. That was not my intent. The post was supposed to just be at least an accurate documentation of what I found, with the exact details of what did and did not work in a useful manner for me - a report, if you will - including some material evidence of how they had functioned for people to draw their own conclusions from, and generally peppered with own opinion regarding why things seemed the way they were as often that guided the steps I took while investigating.

Back when I was making a purchasing decision, I searched all over these forums, and elsewhere, for information on what on earth I could expect in terms of the actual audio I might get out of these kinds of pickup, and I found almost literally no tangible information to help me make a decision. Since microphones are basically a bottomless money pit, when I saw this thread come up, I sought to rectify that situation in the only way I know how. I'm definitely taking on board the information that people have graciously posted, but, I feel like much of it is trying to address a problem that doesn't exist, and I kinda feel we're going around in circles. I'm feeling like I'm unable to communicate correctly as every time I've been making posts like this, I'm getting responses that don't make sense to me.

I mean the recordings are right there in the post. Does it sound like it's not working?
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Instrument mic(s)
« Reply #30 on: December 03, 2018, 12:16:01 AM »

Fair enough Gena. But, in direct response to your question, my units sound fine plugged into 1/4" jacks, if they are microphone inputs.

[and having revisited your original post I think Anahata has described what is happening]
[or, maybe not]

Listening to your samples again, I agree that they sound of a similar tonal quality. The differences I can hear are probably down to slightly different setups.
« Last Edit: December 03, 2018, 12:36:36 AM by Tone Dumb Greg »
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Instrument mic(s)
« Reply #31 on: December 03, 2018, 12:45:38 AM »

I thought you were going to bed?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Instrument mic(s)
« Reply #32 on: December 03, 2018, 08:54:57 AM »

I thought you were going to bed?

I'm an insomniac and a procrastinator. Got there eventually.

 ;D

[I blame Pete for posting the Badger thing]
« Last Edit: December 03, 2018, 08:56:35 AM by Tone Dumb Greg »
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Instrument mic(s)
« Reply #33 on: December 03, 2018, 10:19:19 AM »

Fair enough Gena. But, in direct response to your question, my units sound fine plugged into 1/4" jacks, if they are microphone inputs.

Right, that makes sense - not something I've come across, but, as you say, no reason you couldn't have a 1/4" connector running a mic input.

Anahata's suggestion re TS cables seems like it was right on the money. While I don't have any proper TS cables, the TRS ones I've got have connectors that can be disassembled, so, I figured, why not just add a short between the R and S? Night and day difference for the Microvox's output when connected to the Instrument level 1/4" jacks I have. Seemingly no effect on the Myers, so I assume it detects the jack insertion via a different means, but this Microvox M310 certainly now seems eminently usable in the same situations as the Myers pickup - via both the mic inputs and via the instrument level inputs I have access to.

So, I guess I have some recordings to revise! I can't imagine potentially having its power supply disabled entirely did the M310 any favours, so, I'll try to get a couple of proper TS cables and have another stab at them for posterity, although figuring out how to attach both of them again will be fun. And I guess I should put a sticker to put on the side of this M310 pickup saying 'TS CABLES ONLY'. Watch this space I guess.
Logged

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Instrument mic(s)
« Reply #34 on: December 03, 2018, 11:07:45 AM »

Fair enough Gena. But, in direct response to your question, my units sound fine plugged into 1/4" jacks, if they are microphone inputs.

...Right, that makes sense - not something I've come across, but, as you say, no reason you couldn't have a 1/4" connector running a mic input...


It's not uncommon. I use two PAs regularly with 1/4" mic jacks. A QTX 12 PA and a Roland Street Cube.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Instrument mic(s)
« Reply #35 on: December 03, 2018, 11:30:31 AM »

Anahata's suggestion re TS cables seems like it was right on the money. While I don't have any proper TS cables, the TRS ones I've got have connectors that can be disassembled, so, I figured, why not just add a short between the R and S? Night and day difference for the Microvox's output when connected to the Instrument level 1/4" jacks I have.

Huzzah!
And credit to you for supplying enough detail to pinpoint the problem, even if you doubted it was relevant.

I don't know how the Myers unit is assembled, but the worst that's likely to happen if you use the Myers with a TS plug is that the signal will become unbalanced, and you'll lose some interference rejection. The Microvox is unbalanced anyway and therefore susceptible to interference in the first place. You'll only notice the difference one day when there's some high powered triac-controlled stage lighting, or a gaming machine in the building (as happened to me back in the days of unbalanced mic cables) or somebody's mobile phone nearby.
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Instrument mic(s)
« Reply #36 on: December 03, 2018, 07:59:30 PM »

Holy hell...it’s quite complicated innit? I used to be interested in all that tech stuff... but now I just want to plug it in and have it work...   :Ph
 I’ve just ordered a Thomann's t.bone cc 75..

-Y-

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 896
  • Handry 18 (G/C), Mélodie (D), Club IIb (A/D)
    • a database of nearly 500 melodeons here
Re: Instrument mic(s)
« Reply #37 on: December 03, 2018, 08:43:31 PM »

You've just uncovered the infinite realm of sound geeking :) Quite possible to get lost indeed.

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Instrument mic(s)
« Reply #38 on: December 03, 2018, 09:04:48 PM »

Holy hell...it’s quite complicated innit? I used to be interested in all that tech stuff... but now I just want to plug it in and have it work...   :Ph
 I’ve just ordered a Thomann's t.bone cc 75..

Just one?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Dick Rees

  • Neo-Luddite
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1640
Re: Instrument mic(s)
« Reply #39 on: December 03, 2018, 09:16:32 PM »

I own a sound company.  Listen to Anahata...
Logged
"You're making the wrong mistakes."
...Thelonius Monk

"I never made one of my discoveries through the process of rational thinking."
...Albert Einstein

"If Art Tatum took up classical music seriously, I'd quit my job the next day."
...Vladimir Horowitz
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal