Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Removing bellows pins...best tool for the job?  (Read 7562 times)

0 Members and 1 Guest are viewing this topic.

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Removing bellows pins...best tool for the job?
« on: November 26, 2018, 10:27:41 AM »

I'm attempting to remove the bellows from a 1040, and the pins are remarkably reluctant to move.

I've tried pliers and molegrips of all shapes and sizes but failed miserably.


Suggestions please Ta
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Eshed

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 447
Re: Removing bellows pins...best tool for the job?
« Reply #1 on: November 26, 2018, 10:32:25 AM »

I'm attempting to remove the bellows from a 1040, and the pins are remarkably reluctant to move.

I've tried pliers and molegrips of all shapes and sizes but failed miserably.
Before trying other implements of destruction, I usually had more luck with pliers etc. when also applying pressure on the instrument (pushing the bellows closed as hard as I can).
Trying to unscrew them rather than pulling them straight out also helps.
Quite possible that you've already tried this :)
Logged
Do you have a Hohner from 1934-1945 with a serial number on?
Send me a private message or comment on the German Accordion Problem spreadsheet to improve the statistics of the project and get an estimate of the production date of the box if it is not known.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Removing bellows pins...best tool for the job?
« Reply #2 on: November 26, 2018, 11:26:12 AM »

Pair of THESE





AnnC

  • Succumbing to MAD 😊
  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 492
  • Forget the tea, just pass me a large Gin 🍸
Re: Removing bellows pins...best tool for the job?
« Reply #3 on: November 26, 2018, 11:40:07 AM »

 (:) I use the same as Lester but modified, following advice found on Melnet, by blunting the cutting edges and filing a little semi-circular notch in the centre of each jaw to avoid cutting the pin head off as it's pulled out, worked fine for me  ;D
Logged
On the bracing North Yorkshire Coast :D

 You hum it pet.......I'll play it......but not necessarily in the same key 🎶😊
 3 lovely Liliputs, a Preciosa, a Pokerwork & a C/G Anglo concertina :D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing bellows pins...best tool for the job?
« Reply #4 on: November 26, 2018, 11:54:34 AM »

Yes end cutters are the best tool, modified as Ann describes.   If the pins are very tight try heating them with a hot soldering iron, but get the end cutters first.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Removing bellows pins...best tool for the job?
« Reply #5 on: November 26, 2018, 12:03:37 PM »

I also use the end cutters wtih a slight notch filed in the jaws, as described by Ann.

Additionally, I use a small square patch of thin chamois leather, about 2 cm square, with a small hole punched in the middle. This fits over the head of the bellows pin while still allowing the end cutters to grip the pin. It protects the casework of the instrument from being damaged. Some might dismiss this precaution as unneccesary but I don't take any chances, especially with a nice wood finish on the casing.

The other crucial thing to watch is to ensure the bellows pins are pulled out using a straight perpendicular pull; no sideways rocking which will only damage the hole or bend the pin, or both...
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Removing bellows pins...best tool for the job?
« Reply #6 on: November 26, 2018, 12:13:53 PM »

I also use modified end-cutters for this job. They were dirt cheap in a market somewhere, and would have been useless as end-cutters anyway. I think they cost me a quid (or less - I probably got some pliers and side-cutters thrown in for that quid).

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Removing bellows pins...best tool for the job?
« Reply #7 on: November 26, 2018, 01:11:51 PM »

I use 3 different pliers. On the right is a modified end cutter (purchased from Kimric of this parish) that I use particularly on pins with a grip groove on the head.

On the left in the first picture is a narrow jaw plier when the width of the end cutter might cause damage to nearby trim (photo 2 is evidence from someone before me). I also prefer it on the small pin Hohners. I clamped the jaws onto a spinning spherical diamond rotary tool so it has two hemispherical indents (pic 3) that strongly grip the head so difficult/rusty pins are easily rotated to aid extraction. The end cutters tend to scrape a groove into the pin when trying to rotate a pin.

The middle pliers have linen filled phenolic jaw inserts with added hemispherical indents. I use these on high end boxes like Castagnaris which use brass pins. The heads on brass pins are easily marred by pliers so this completely eliminates that danger.

In between the 3 pliers in pic 1 are reamers for exact sizing of holes for pins.

The last picture is a larger diameter nail set embedded into a golf ball for painless pin pushing.

Scott

BellingersButtonBoxes.com
« Last Edit: November 26, 2018, 01:13:52 PM by hickory-wind »
Logged
too many boxes...please buy one, or two, or

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Removing bellows pins...best tool for the job?
« Reply #8 on: November 26, 2018, 01:20:29 PM »

The middle pliers have linen filled phenolic jaw inserts with added hemispherical indents.
That's a very useful tool, Scott. Did you make this, or are the pliers with phenolic inserts available commercially?
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Removing bellows pins...best tool for the job?
« Reply #9 on: November 26, 2018, 02:49:19 PM »

For steel pins which are really stuck fast, I would consider one of these below. If nothing else, and with a bit of skill, it would burn away the unwanted old wood and leave the pin unscathed!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Removing bellows pins...best tool for the job?
« Reply #10 on: November 26, 2018, 02:53:36 PM »

Unscathed?  The nickel plating won't look too good after that.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Removing bellows pins...best tool for the job?
« Reply #11 on: November 26, 2018, 03:04:23 PM »

You could be right (again!) there, Theo. Back to the drawing board!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Removing bellows pins...best tool for the job?
« Reply #12 on: November 26, 2018, 03:57:08 PM »

same end cutters as others.  I have drilled a small hole in the jaws to accommodate the 'stalk' of the pins   by mounting the end cutters blade uppermost in the drill vice of my bench piller drill  and drilling the hole centred on the two cutting edges of the pliers.   The pincers can't cut into the pin  and stubborn pins can be extracted by putting the box on the floor to enable a strong vertical pull to be applied  with greater strength than if placed on the;bench


george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Removing bellows pins...best tool for the job?
« Reply #13 on: November 26, 2018, 05:06:07 PM »

All this talk of filing and drilling end cutters makes me think they can't be like mine. They're Swedish and you could file them all you liked. It would just blunt the file.
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Removing bellows pins...best tool for the job?
« Reply #14 on: November 26, 2018, 05:09:03 PM »

The middle pliers have linen filled phenolic jaw inserts with added hemispherical indents.
That's a very useful tool, Scott. Did you make this, or are the pliers with phenolic inserts available commercially?

I repurposed two of the pliers. They were designed for eyeglass technicians and I'm not sure of the original function. The all metal one doesn't close all the way which is fine when pulling pins. Do a search for optical pliers and you should find nylon jawed style. I doubt they still use the linen filled phenolic. It took about 30 seconds with a spherical diamond tool to create the divots.

Scott
Logged
too many boxes...please buy one, or two, or

Anahata

  • This mind intentionally left blank
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 6767
  • Oakwood D/G, C/F Club, 1-rows in C,D,G
    • Treewind Music
Re: Removing bellows pins...best tool for the job?
« Reply #15 on: November 26, 2018, 05:30:07 PM »

All this talk of filing and drilling end cutters makes me think they can't be like mine. They're Swedish and you could file them all you liked. It would just blunt the file.

Yes, I think this is a case where cheap, soft and blunt is actually ideal for the job!
Logged
Слава Україні !
Music recording and web hosting: www.treewind.co.uk
Mary Humphreys and Anahata: www.maryanahata.co.uk
Ceilidh band: www.barleycoteband.co.uk

george garside

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5401
Re: Removing bellows pins...best tool for the job?
« Reply #16 on: November 26, 2018, 08:15:51 PM »

Indeed, mine are Lidles best! - or was it Aldi

george
Logged
author of DG tutor book "DG Melodeon a Crash Course for Beginners".

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Removing bellows pins...best tool for the job?
« Reply #17 on: November 26, 2018, 10:24:47 PM »

Indeed, mine are Lidles best! - or was it Aldi

george
..in which case the ballad if LiDl and Aldi is probably relevant...
https://youtu.be/cL7jyXCQ2Zc

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Removing bellows pins...best tool for the job?
« Reply #18 on: November 27, 2018, 12:52:06 AM »

The middle pliers have linen filled phenolic jaw inserts with added hemispherical indents.
That's a very useful tool, Scott. Did you make this, or are the pliers with phenolic inserts available commercially?

I repurposed two of the pliers. They were designed for eyeglass technicians and I'm not sure of the original function. The all metal one doesn't close all the way which is fine when pulling pins. Do a search for optical pliers and you should find nylon jawed style. I doubt they still use the linen filled phenolic. It took about 30 seconds with a spherical diamond tool to create the divots.
Thanks, Scott!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Removing bellows pins...best tool for the job?
« Reply #19 on: November 27, 2018, 07:21:01 AM »

Another good tip is to put the pins back into the holes they came from and certainly make sure the Bellows are the same orientation.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal