Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tuning issue - pulling effect?  (Read 5149 times)

0 Members and 1 Guest are viewing this topic.

melodona

  • Member
  • *
  • Offline Offline
  • Posts: 31
    • Melodona Accordions
Tuning issue - pulling effect?
« on: September 02, 2009, 08:12:06 PM »

hello

I have a little problem with a musette here...

so one reed at 0 and one at +9 cents
when played on the tuning bellows, sounds fine
I hear the beating and all
but inside the accordion, it won't beat
I get one tone made of what seems to be
two notes both at +5

I was just told about this "pulling"
that sometimes happen
two notes pulling each other to the center
and sounding "� l'unison" instead of beating
but in the case of dryer tuning (4 cents and under)
not 9...
besides, it's the only one doing that
the others are fine

any ideas?
suggestions?

thank you

Melodona
« Last Edit: March 12, 2012, 12:43:15 PM by Theo »
Logged

stevejay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
Re: Tuning issue - pulling effect?
« Reply #1 on: September 02, 2009, 11:51:18 PM »

Agreed, somewhat metaphysical if something else was being compared. None of this is helping though.
« Last Edit: September 03, 2009, 12:00:49 AM by stevejay »
Logged

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: Tuning issue - pulling effect?
« Reply #2 on: September 03, 2009, 01:03:11 AM »

hello

I have a little problem with a musette here...

so one reed at 0 and one at +9 cents
when played on the tuning bellows, sounds fine
I hear the beating and all
but inside the accordion, it won't beat
I get one tone made of what seems to be
two notes both at +5

I was just told about this "pulling"
that sometimes happen
two notes pulling each other to the center
and sounding "à l'unison" instead of beating
but in the case of dryer tuning (4 cents and under)
not 9...
besides, it's the only one doing that
the others are fine

any ideas?
suggestions?

thank you

Melodona
Make sure both reeds have exactly the same 'set'.  If they don't, weird things can happen....
Logged

melodona

  • Member
  • *
  • Offline Offline
  • Posts: 31
    • Melodona Accordions
Re: Tuning issue - pulling effect?
« Reply #3 on: September 03, 2009, 04:38:35 AM »

can you define "set" please?

thanks

M
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning issue - pulling effect?
« Reply #4 on: September 03, 2009, 07:51:19 AM »

can you define "set" please?
The 'set' is the height of the reed tongue above the surface of the reed plate. Generally there should be a gap at the reed tongue tip approximately equal to the thickness of the reed tongue itself. It is this gap which enables the reed to vibrate properly when bellows air pressure is applied.

If the gap is too large, the reed is slow to start and may need extra bellows pressure to get it to sound at all. The sound will be 'breathy' and rather on the loud side. If the gap is too small, the reed may start easily under low bellows pressure, but is liable to 'choke' and stop sounding as pressure increases.

After filing a reed to adjust the pitch, the residual stresses in the metal tongue usually mean that the set needs to be adjusted. To alter the set of a reed you need to very gently bend the tongue up or down as required.

To bend the tongue up, use a thin steel shim or blade under the reed tip and gently ease it upwards a few millimetres before letting it return to place. To bend the tongue down, similarly press the reed tongue down into the reed frame slot using a wooden cocktail stick or similar wooden pointy thing. Proceed very gently and carefully a bit at a time and test the reed's response at every turn.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Tuning issue - pulling effect?
« Reply #5 on: September 03, 2009, 08:22:03 AM »

can you define "set" please?
The 'set' is the height of the reed tongue above the surface of the reed plate. Generally there should be a gap at the reed tongue tip approximately equal to the thickness of the reed tongue itself. It is this gap which enables the reed to vibrate properly when bellows air pressure is applied.

If the gap is too large, the reed is slow to start and may need extra bellows pressure to get it to sound at all. The sound will be 'breathy' and rather on the loud side. If the gap is too small, the reed may start easily under low bellows pressure, but is liable to 'choke' and stop sounding as pressure increases.

After filing a reed to adjust the pitch, the residual stresses in the metal tongue usually mean that the set needs to be adjusted. To alter the set of a reed you need to very gently bend the tongue up or down as required.

To bend the tongue up, use a thin steel shim or blade under the reed tip and gently ease it upwards a few millimetres before letting it return to place. To bend the tongue down, similarly press the reed tongue down into the reed frame slot using a wooden cocktail stick or similar wooden pointy thing. Proceed very gently and carefully a bit at a time and test the reed's response at every turn.

That is the problem with these technical adjustments, you people who can do it hide behind highly technical language such as "wooden pointy thing". Can't you make it simpler for us mere mortals?
 ;D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning issue - pulling effect?
« Reply #6 on: September 03, 2009, 10:00:34 AM »

Make sure both reeds have exactly the same 'set'.  If they don't, weird things can happen....

I've just tuned a box where exactly the same thing happened.  Outside the box, nice even tremolo all across the range, inside the box all ok except the G/A on the G row has no tremolo at all.   Take it out double check, check tuning and set, check valves, all ok.  Reassemble box and the problem is still there. 

Solution:   fit a brace between the reedblocks.  Nearly all Italian boxes have these as standard,  so do Weltmeisters, and some older Hohners.   Italians use a strip of brass or aluminium screwed across the top of the reedblocks, Germans use short steel rods wedged between the blocks.  These have the effect of making the reedblock assembly more rigid this preventing unwanted resonant vibrations of the blocks themselves. 
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Tuning issue - pulling effect?
« Reply #7 on: September 03, 2009, 02:29:56 PM »

Solution:   fit a brace between the reedblocks.  

I always wondered what that metal pointy thing was for! Can add that my Gaillard has an aluminium frame supporing the blocks, in addition the the 'metal pointy thing'. The whole thing looks immensely rigid. All is revealed, Thanks D3R
Logged
  _       _    _      _ 

melodona

  • Member
  • *
  • Offline Offline
  • Posts: 31
    • Melodona Accordions
Re: Tuning issue - pulling effect?
« Reply #8 on: September 03, 2009, 02:43:45 PM »

thanks
I just always called it "gap"
and yes, always make sure they're all fine before starting to tune

and for the brace... this accordion has them already
I just unscrew them to tune and put them back at the very end
usually doesn't change anything
but this time... indeed... I tried putting them back and... (drum roll) BINGO!!!

Theo... I loved you the minute I registered  :-*
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Tuning issue - pulling effect?
« Reply #9 on: September 03, 2009, 03:23:00 PM »

Make sure both reeds have exactly the same 'set'.  If they don't, weird things can happen....

I've just tuned a box where exactly the same thing happened.  Outside the box, nice even tremolo all across the range, inside the box all ok except the G/A on the G row has no tremolo at all.   Take it out double check, check tuning and set, check valves, all ok.  Reassemble box and the problem is still there. 

Solution:   fit a brace between the reedblocks.  Nearly all Italian boxes have these as standard,  so do Weltmeisters, and some older Hohners.   Italians use a strip of brass or aluminium screwed across the top of the reedblocks, Germans use short steel rods wedged between the blocks.  These have the effect of making the reedblock assembly more rigid this preventing unwanted resonant vibrations of the blocks themselves. 


Spookily enough, the same thing happened to me this morning. How weird?
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning issue - pulling effect?
« Reply #10 on: September 03, 2009, 05:02:24 PM »


Theo... I loved you the minute I registered  :-*

Now I need an emoticon for blush!   Where is LDT when you need her!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

triskel

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3290
Re: Tuning issue - pulling effect?
« Reply #11 on: September 07, 2009, 02:55:25 AM »

Now I need an emoticon for blush!   Where is LDT when you need her!
 

We've already got one called Embarrassed = :-[ , would that do?

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning issue - pulling effect?
« Reply #12 on: September 07, 2009, 08:15:41 AM »

Now I need an emoticon for blush!   Where is LDT when you need her!
 

We've already got one called Embarrassed = :-[ , would that do?

Yes its close, but there is a distinct difference between blushing with pleasure and embarrassment.   
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mory

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 752
Re: Tuning issue - pulling effect?
« Reply #13 on: February 20, 2013, 08:28:45 AM »

Solution:   fit a brace between the reedblocks. 

I always wondered what that metal pointy thing was for! Can add that my Gaillard has an aluminium frame supporing the blocks, in addition the the 'metal pointy thing'. The whole thing looks immensely rigid. All is revealed, Thanks D3R

Got a picture you could post please Chris All the Best mory
Logged

Chris Ryall

  • "doc 3-row"
  • French Interpreter
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 11154
  • Wirral UK
    • Chris Ryall
Re: Tuning issue - pulling effect?
« Reply #14 on: February 20, 2013, 08:34:07 AM »

My camera hasn't worked since Melodeons & More, the year after I posted that, but I'll see what this new Ipad can muster ..
Logged
  _       _    _      _ 

pikey

  • Addicted to squeezeboxes since 1975
  • Thread mod
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3364
  • If it moves, I'll squeeze it....
Re: Tuning issue - pulling effect?
« Reply #15 on: February 20, 2013, 09:13:10 AM »

Make sure both reeds have exactly the same 'set'.  If they don't, weird things can happen....

I've just tuned a box where exactly the same thing happened.  Outside the box, nice even tremolo all across the range, inside the box all ok except the G/A on the G row has no tremolo at all.   Take it out double check, check tuning and set, check valves, all ok.  Reassemble box and the problem is still there. 

Solution:   fit a brace between the reedblocks.  Nearly all Italian boxes have these as standard,  so do Weltmeisters, and some older Hohners.   Italians use a strip of brass or aluminium screwed across the top of the reedblocks, Germans use short steel rods wedged between the blocks.  These have the effect of making the reedblock assembly more rigid this preventing unwanted resonant vibrations of the blocks themselves. 


Spookily enough, the same thing happened to me this morning. How weird?

Must be the pulling effect of the meteors  ;)
Logged
Still squeezing after all these years.
Mostly on hohners , with a couple of Dinos and a smattering of anglos - and now a Jeffries duet

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Tuning issue - pulling effect?
« Reply #16 on: February 20, 2013, 11:00:20 PM »

I put one of those metal strips on the reed blocks of a 4 voice today.
It certainly improved the outside row but does not seem to have had any positive effect on the inside row.
Would anyone have any idea why that might be?
Reeds pulling together in pitch is usually caused by a (torsional) resonance of the reed block, often this only affects one note and can usually be cured by bracing the middle of the blocks either to each other or to the case.
It won't fix any other problem though. Is the problem with the inside row the same (reeds pulling together in pitch or warbling) as the outside row or something different?
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal