Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: tuning 'table'  (Read 3597 times)

0 Members and 1 Guest are viewing this topic.

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
tuning 'table'
« on: September 04, 2009, 01:05:07 PM »

I'm thinking of making a simple 'tuning table' by making a frame on thin plywood that will attatch to the end of a pokerwork bellows which will have a hole in it against which I can hold the reed block to actuate the approptiate reed for tuning.  Has anyone made such a thing?  If so,a picture would be most helpful.

Michael
Logged

an bosca ceoil

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 347
Re: tuning 'table'
« Reply #1 on: September 04, 2009, 01:40:15 PM »

If you are thinking about a permanant set-up, IMO you would do better to use a redundant PA bellows, rather than wasting pokerwork ones. Charlie Watkins aka WEM was offering ready made ones, so you might be able to crib from his pictures. You can use one air hole to tune out of the box, but might consider covering the entire "lid" with felt/leather so that you could sound the complete end  by each button with the blocks in situ.
Logged

waltzman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 943
Re: tuning 'table'
« Reply #2 on: September 04, 2009, 02:21:03 PM »

My plan was not to 'waste' any bellows.  The plate would attatch temporarily to the treble end of a pokerwork to allow tuning outside the box then the plate would be removed and the box reassembled.  Not as handy as a permanent tuning table but I think it would work.
Logged

TomB-R

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 598
Re: tuning 'table'
« Reply #3 on: September 04, 2009, 06:17:37 PM »

Sorry I realise a picture would be more helpful but can't do that today.

For mine I got some redundant PA bellows on Ebay, plywood top and bottom. The top piece is long enough so that I can clamp the excess to my bench when using the thing.

Considering myself lucky in having a bandsaw I made a couple of angled cuts in a thick piece of plywood so that the "valley" between the cuts would have a range of widths to cover most of the reed plates I wanted to tune.  Both the outside of the valley pieces were glued to a backing piece with a hole in it (for the air) and an offcut of the middle piece was glued in to close one end of the "valley." Another offcut was left free and that slides in the valley to close the valley at the the other end of the reed plate.  The whole thing is placed over the hole in the bellows when I want to use it.

I use my knee under the bellows to actuate the process!

A pic would be so much easier!

Similar to this (and prob inspired by it) but much simpler.

http://www.youtube.com/watch?v=U--Vf99jyTA&feature=channel_page
« Last Edit: September 04, 2009, 06:21:52 PM by TomB-R »
Logged

Christopher K.

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 894
Re: tuning 'table'
« Reply #4 on: September 04, 2009, 06:44:25 PM »

This is a picture from a flickr group.  The owner of the photo (and the owner of the stockinged foot) is someone I know from another forum.  Presumably, the block can be fastened back to the keyboard, flipped in a position which is opposite that which is shown here, and the whole bit tested in situ as shy talk describes.

Edit:  I mean 'presumably' to mean that theoretically, one could install a sliding panel with a variable aperture.  Slide it wide enough for a single reed to be tuned outside of the bellows, and then finish up and test the whole rig by widening the aperture to accommodate the whole block, then reattaching the blocks to the treble end, and flipping over so the reeds go in the bellows and the keyboard faces up.

Edit too: Or for a more practical setup that is easier to imagine constructing, you can shoot from the hip as the master tuner from the Weltmeister factory does.  No springs, no platform, just right on top of the bench (watch around the 3:00 mark).  Some ear!

http://www.youtube.com/watch?v=rYsSifiDapo&feature=related


 
« Last Edit: September 04, 2009, 06:58:04 PM by cpsmart »
Logged

stevejay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
Re: tuning 'table'
« Reply #5 on: September 04, 2009, 07:02:31 PM »

Wow..

It seems in my very uneducated opinion, if you can tune a melodeon, the rest of the repairs are a lot simpler by comparison. Tuning seems to be a pain, even for the experts her. There are a lot of variables.

I would really like to be able to fine tune a melodeon, but I suspect it will never happen for me. Watching the process would be fascinating, I'll check out some vids if available.

People who can tune well deserve respect.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: tuning 'table'
« Reply #6 on: September 05, 2009, 12:03:27 AM »


I would really like to be able to fine tune a melodeon,


Talking about "fine" tuning makes it sound as if there is some other kind eg "almost" tuning  or "coarse" tuning.

There is only tuning, either its in tune or its not.  I suppose you could argue there is fine out of tuning as opposed to grossly out of tune.

But to be serious its a skill that probably most people could learn,  it does require attention to detail, good control of hands and fingers, practice, and a good ear.  Not unlike learning to play  ;)
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

stevejay

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 709
Re: tuning 'table'
« Reply #7 on: September 05, 2009, 01:54:07 AM »

My C/F was sent for tuning and I'm not 100% happy with the results.. some notes sound a bit off, but I find I am starting to play certain notes with a different touch to compensate. Funny thing, as I get better, I notice it LESS  :D

Maybe as I get quicker, I'm lingering on all the notes a bit less. It was rewaxed, so at least the reeds have less chance of falling out. Now that would sound pretty bad.

I heard a story about a guy trying to tune with an overhead ceiling fan in motion. If you have ever notice what that can do to the sound of a reed instrument, it must have been pretty disturbing to him until he realized what forces of physics were in play there.
« Last Edit: September 05, 2009, 02:00:33 AM by stevejay »
Logged

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: tuning 'table'
« Reply #8 on: September 18, 2009, 12:43:25 PM »

This is a picture from a flickr group.

This looks very similar to the table I built a while ago. Oddly enough mine now has a blue top too.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: tuning 'table'
« Reply #9 on: September 18, 2009, 03:15:43 PM »

Theo

"Almost tuning"  is what Hohner does.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: tuning 'table'
« Reply #10 on: September 18, 2009, 03:45:48 PM »

Theo

"Almost tuning"  is what Hohner does.

On a good day!   :o
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Quebecois

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1206
  • Accordez-vous donc, c'est si beau, l'accordéon!
Re: tuning 'table'
« Reply #11 on: September 18, 2009, 05:43:46 PM »

Come on, if Hohners were properly tuned they wouldn't have that "Hohner sound" :o
Logged
Hohner Morgane D/G, pre-Erica Hohner in C/F and G/C,
Hohner Erica A/D, Roland FR-18

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: tuning 'table'
« Reply #12 on: September 18, 2009, 11:19:26 PM »

Come on, if Hohners were properly tuned they wouldn't have that "Hohner sound" :o

No really they still do have the distinctive Hohner sound, but better.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Aaro

  • Good talker
  • **
  • Offline Offline
  • Posts: 78
    • Luukinen Accordions
Re: tuning 'table'
« Reply #13 on: September 19, 2009, 07:23:23 AM »


I have almost a similar tuning table. Very handy. I am use tuning table many years and I have not regretted it.
Other way, is tune the reeds in your own box. Test bellows or similar.

Aaro
Logged
Luukinen Accordions offers a full line of fine handcrafted custom made accordions.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal