Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Converting a two row to a one row  (Read 9217 times)

0 Members and 1 Guest are viewing this topic.

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Converting a two row to a one row
« on: January 29, 2019, 08:28:20 PM »

The project I have in mind is to convert a Hohner Erica to a one row, 4-voice LMMH melodeon.
In order to minimize alterations, I intend to pair the levers so that each button operates two pallets.
This approach will obviate the necessity to alter or replace the soundboard. Another plus is the fact that it will
not be necessary to extend the pallet levers or replace the existing pallets.
One reed block will hold the MM reeds. The second block will need to be modified to accommodate
the H and L reeds.
All the buttons will be removed from the outside row, and the holes will be closed off.

The main task is to couple or bridge the pallet levers. My instinct tells me that this would work
best if done behind the fingerboard rather than closer to the pallets.
I expect that the springs may need to be adjusted to compensate for the additional load.
Otherwise, the action would be sluggish or heavy.
At this stage I am not planning to incorporate slides and stops, but I have not ruled it out completely.

The connection between the levers will need to be rigid if it is to work properly.
I would appreciate advice on what might be a good method of bridging a pair of pallet levers.
Would soldering work? Or possibly an adhesive of some kind?
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Converting a two row to a one row
« Reply #1 on: January 29, 2019, 08:34:34 PM »

That is an intriguing idea :)
Definitely couple the pallets at the fingerboard.
Firstly, I would try a small piece of hardwood glued between the levers with Araldite.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Converting a two row to a one row
« Reply #2 on: January 29, 2019, 08:41:15 PM »

Hi Pearse Rossa,

Some of the early Walters and Baldonis were made with two pallets linked to one button.  Those usually involve a linkage near the pallets.

I mentioned this to Laurent Jarry who works on accordions in his Paris shop, La Boite D'accordéon. He wanted a 6 voice 1-row box and I mentioned that he could convert a 3-voice 2-row Saltarelle to a 6 voice 1-row. I sent him photos of the early Baldonis & Walters with paired, staggered pallets to achieve a 6 voice or 8 voice box. 

And he actually did it!  Laurent converted a 3 voice 2 row Saltarelle to a 1 row 6 voice box. I think he linked the button levers by pairs under the keyboard plate. Maybe he would send you pics?

Best,

PG
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #3 on: January 29, 2019, 09:12:06 PM »

Firstly, I would try a small piece of hardwood glued between the levers with Araldite.
Worth a shot. Thanks.

La Boite D'accordéon..... Laurent converted a 3 voice 2 row Saltarelle to a 1 row 6 voice box. I think he linked the button levers by pairs under the keyboard plate. Maybe he would send you pics?
I've found his website. I might contact him for photos. Thanks.
Do you happen to know how he managed to secure the linkage?
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Converting a two row to a one row
« Reply #4 on: January 29, 2019, 09:22:10 PM »

Firstly, I would try a small piece of hardwood glued between the levers with Araldite.
Worth a shot. Thanks.

La Boite D'accordéon..... Laurent converted a 3 voice 2 row Saltarelle to a 1 row 6 voice box. I think he linked the button levers by pairs under the keyboard plate. Maybe he would send you pics?
I've found his website. I might contact him for photos. Thanks.
Do you happen to know how he managed to secure the linkage?

No, Laurent sent me a photo of the completed conversion but not of the mechanics under the keyboard. But, he's a very skilled and experienced accordion mechanic and also builds accordinas.

I can send or post photos of the 1930s Baldonis and Walters boxes that have 2 pallets linked to one button. There were several different ways that this was tried!  But some of  the early ones really do remind me of converted 2 row boxes, because the pallets are staggered (although the same number of pallets in each row, rather than 11 + 10 as on your Erica). Some of the later ones have the paired pallets and airways "in line."

I think a couple of years ago Theo Gibb had for sale a Delicia (?) box with one row of buttons and 4 voices that appeared to be a converted 2 row MM box. Maybe he will recall this or even have photos.

Let us know how you get on!

PG
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Converting a two row to a one row
« Reply #5 on: January 29, 2019, 09:31:15 PM »

An easier bet would be to couple an 8 bass left end to a 4 stop treble end, surely? I've been busy collecting the parts to accomplish just this, but won't be able to get any further with it till the summer, as my Liliputs are stealing most of my time at the moment, plus I'll be missing for the next five weeks.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #6 on: January 29, 2019, 10:17:03 PM »

I can send or post photos of the 1930s Baldonis and Walters boxes that have 2 pallets linked to one button.
Please post them here. That would be very much appreciated.

Quote
I think a couple of years ago Theo Gibb had for sale a Delicia (?) box with one row of buttons and 4 voices that appeared to be a converted 2 row MM box. Maybe he will recall this or even have photos.
Sounds interesting.

An easier bet would be to couple an 8 bass left end to a 4 stop treble end, surely?
I like a challenge!... and I've already done that.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #7 on: January 29, 2019, 10:24:02 PM »

Firstly, I would try a small piece of hardwood glued between the levers with Araldite.
The more I think about this, the better I like the idea.
Maybe even a double link for maximum rigidity?
And the process can easily be reversed.
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Converting a two row to a one row
« Reply #8 on: January 30, 2019, 06:08:45 AM »

I can send or post photos of the 1930s Baldonis and Walters boxes that have 2 pallets linked to one button.
Please post them here. That would be very much appreciated.


See below photos of the pallets of two instruments with "staggered" design for their 2 pallets per button:

1) the F. Likely 10 key 1-row 6 voice Baldoni, and
2) an early Walters 15 key 1.5-row 8 voice box.

PG
« Last Edit: January 30, 2019, 06:25:42 AM by pgroff »
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Converting a two row to a one row
« Reply #9 on: January 30, 2019, 06:19:19 AM »

And here are two instruments with two different lever mechanisms but each with an "in-line" design for their 2 pallets / button:

1)  a 10-key 8-voice Walters 1-row, and

2) a 13 key 8 voice Baldoni.

The Walters is fully described here:
http://forum.melodeon.net/index.php/topic,11281.0.html


« Last Edit: January 30, 2019, 06:27:29 AM by pgroff »
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Converting a two row to a one row
« Reply #10 on: January 30, 2019, 06:41:14 AM »

I worked on a VERY old Paolo Soprani chromatic that had a slave row of buttons that operated the arms by a bend that caught the arm of the valve it wanted to lift. It was very simple and worked well.
 You would do the reverse where the button you were pressing would have a tab soldered on sticking off to the side where it would either press or lift the arm next to it depending on weather the link was near the pads or under the keyboard.

Use zinc chloride flux and you will have no trouble soldering to the steel arms.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #11 on: January 30, 2019, 06:47:09 PM »

See below photos...
Thanks Paul. Very useful.

Use zinc chloride flux and you will have no trouble soldering to the steel arms.
Thanks for the tip.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #12 on: February 01, 2019, 08:17:47 PM »


I expect that the springs may need to be adjusted to compensate for the additional load.
Otherwise, the action would be sluggish or heavy.
Having investigated this aspect of the task more thoroughly, I don't think adjustments will be necessary after all.
Releasing the springs on the redundant button levers, and probably removing them from the rod/axle entirely, should work.
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Converting a two row to a one row
« Reply #13 on: February 01, 2019, 08:46:08 PM »

Are you sure?  A spring strong enough to keep 1 pallet closed is not necessarily strong enough to keep 2 pallets closed.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #14 on: February 01, 2019, 09:01:51 PM »

Not entirely sure, but I think it might work. It will be very easy to test in any event.
I think there is plenty of tension on one spring to operate two pallets.
The pallet is extremely light.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Converting a two row to a one row
« Reply #15 on: February 01, 2019, 09:52:18 PM »

Not entirely sure, but I think it might work. It will be very easy to test in any event.
I think there is plenty of tension on one spring to operate two pallets.
The pallet is extremely light.


It is not the weight of the pallet that the spring is there for, it is to resist the pallets being opened by air pressure on blow notes. So I'm not sure that a single spring will have sufficient tension to hold two pallets closed when playing with enthusiasm.

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #16 on: February 01, 2019, 10:04:53 PM »

Of course. As I say, it is easy to experiment with it.
If this works, then it is a better remedy than having 2 springs per button, which would be heavy and need
fine adjustment.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Converting a two row to a one row
« Reply #17 on: February 01, 2019, 10:20:34 PM »

How about using single springs from a 4 stop, they seem to manage to seal off 4 holes OK? Or are they entirely different?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #18 on: February 01, 2019, 11:19:09 PM »

That's an idea. I don't anticipate that sorting it out will be a major problem.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Converting a two row to a one row
« Reply #19 on: February 02, 2019, 08:19:21 AM »

How about using single springs from a 4 stop, they seem to manage to seal off 4 holes OK? Or are they entirely different?
Not entirely different but possibly significantly different as the 1 row only has one pivot for arm rather than the proposed double arm, so more mechanical friction.
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal