Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3   Go Down

Author Topic: Converting a two row to a one row  (Read 9253 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Converting a two row to a one row
« Reply #20 on: February 02, 2019, 02:11:03 PM »

Assuming that both rows of keys share a common axle, is it possible simply to leave the key levers of the redundant row in place beneath the finger board with the springs still in situ?

If both sets of keys are on a common axle the centre of rotation of the two sets of keys and pallets must be the same. Then provided the rigidity of the cross connection between the two pallet rods is at least an order of magnitude greater than the rigidity of the springs (rigidity is the inverse of elasticity) the mechanical response of the action should be half way between the responses of the two sets of actions before the conversion- actually it will be a tiny bit faster than the mid point because removing the keys will reduce the mass that the springs have to accelerate to close the pallets when the fingers are lifted off.
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Converting a two row to a one row
« Reply #21 on: February 02, 2019, 05:44:19 PM »

Are you sure?  A spring strong enough to keep 1 pallet closed is not necessarily strong enough to keep 2 pallets closed.

I'm not an accordion builder but some of the designs I've seen offer very light button feel and fast action - these include coil spring designs and alternatively designs that have springs acting directly downward on the pallets themselves.

PG
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #22 on: February 02, 2019, 10:53:03 PM »

Assuming that both rows of keys share a common axle, is it possible simply to leave the key levers of the redundant row in place beneath the finger board with the springs still in situ?

Yes, everything is on one axle. I intend leaving the redundant levers in place behind the keyboard.
Earlier I thought this was going to be a problem because the button posts (with the buttons removed)
still protrude beyond the surface of the keyboard. I thought I might have to cut them off at the shaft, which
I would have been very reluctant to do at this stage, but found that they will easily bend inwards out of the way.
As regards the springs, I have experimented and as expected, two springs per button will be far too heavy.
One spring feels about right. If there is pallet blow-back, I will need to adjust the tension on both or try
what Paul has mentioned here;

.... designs that have springs acting directly downward on the pallets themselves.
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: Converting a two row to a one row
« Reply #23 on: February 03, 2019, 03:37:47 PM »

I’ve experimented a lot with springs, and you can make your own without much difficulty and have them provide just the right amount of tension. As someone else mentioned, you could also use the springs intended for a Hohner HA114, and then adjust the tension to your liking.
« Last Edit: February 04, 2019, 01:21:59 AM by mselic »
Logged
C#/D player

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #24 on: February 03, 2019, 05:08:31 PM »

.... you could also use the springs intended for a Hohner HA114...

What type of spring does the HA114 have?
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Converting a two row to a one row
« Reply #25 on: February 03, 2019, 05:32:02 PM »

.... you could also use the springs intended for a Hohner HA114...

What type of spring does the HA114 have?

Like this:
http://www.cgmmusical.co.uk/CGM_Musical_Services/Springs.html#7
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #26 on: February 03, 2019, 07:23:02 PM »

...Which looks to be identical to the Erica springs.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting a two row to a one row
« Reply #27 on: February 03, 2019, 07:26:16 PM »

But thicker.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #28 on: February 04, 2019, 05:46:24 PM »

But thicker.
Is it not just a generic Hohner treble spring?
On Charlie's site it says; "Hohner treble springs model 114 & other models".
I don't see an Erica-specific spring on his website.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Converting a two row to a one row
« Reply #29 on: February 04, 2019, 05:57:19 PM »

Eric as use two different weights of spring.
Insde row (short levers) .5mm wire diameter
Outsidectow (long levers) .55mm wire diameter
114 use the same shape of wire but thicker again I think .65 or .7mm.  I don’t have one handy to measure.
They all look the same from a distance, but the difference in n wire thickness is important.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #30 on: February 04, 2019, 06:17:47 PM »

OK. That makes sense. On the Hohner shop website, you have a variety of springs.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #31 on: February 19, 2020, 07:04:21 PM »

It was only last week that I eventually got around to installing the reeds.
I haven't fine tuned yet. Still mulling over the final sound I want to achieve.
Yesterday I repadded the pallets.
I've never owned a one-row before, mainly because I never really got on with the left-hand side on conventional ones. The very narrow space between the row of buttons and the outer edge of the fingerboard was always an issue for me as well.
On my 'homemade one', I have used a regular two-row fingerboard with the outer row holes sealed off.
Also, I wanted to have better left-hand chord options. For now, it's chords only; G/G, D/A, A/E, F#/B (minus thirds).
The action is not bad, but I think I can improve it further by tweaking the springs.
As I say, I've never played much on a one-row, and I've clocked up less than an hour of playing on this one...
but here's a wee tune.




Logged

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Converting a two row to a one row
« Reply #32 on: February 19, 2020, 07:18:40 PM »

Tidy playing and workmanship.
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

melodeon

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1732
Re: Converting a two row to a one row
« Reply #33 on: February 19, 2020, 09:46:57 PM »

Well done, very clever.
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Converting a two row to a one row
« Reply #34 on: February 19, 2020, 10:44:56 PM »

Math thu!
It sounds and looks good- there's something visually appealing about the pair sof staggerd pallets moving together.
Logged

pgroff

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1827
Re: Converting a two row to a one row
« Reply #35 on: February 19, 2020, 11:39:18 PM »

It was only last week that I eventually got around to installing the reeds.
I haven't fine tuned yet. Still mulling over the final sound I want to achieve.
Yesterday I repadded the pallets.
I've never owned a one-row before, mainly because I never really got on with the left-hand side on conventional ones. The very narrow space between the row of buttons and the outer edge of the fingerboard was always an issue for me as well.
On my 'homemade one', I have used a regular two-row fingerboard with the outer row holes sealed off.
Also, I wanted to have better left-hand chord options. For now, it's chords only; G/G, D/A, A/E, F#/B (minus thirds).
The action is not bad, but I think I can improve it further by tweaking the springs.
As I say, I've never played much on a one-row, and I've clocked up less than an hour of playing on this one...
but here's a wee tune.

Great work, many thanks for sharing this. Hope you don't mind that I shared the video also on facebook (I would delete it if you object).

PG
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Converting a two row to a one row
« Reply #36 on: February 20, 2020, 12:26:35 AM »

Thanks everyone for the positive comments.
I've been "commissioned" to produce two more by friends of mine. I have in mind also to make a six-voice
Baldoni type.
The advice, suggestions and photos that members shared here were very helpful and much appreciated.

Quote
Hope you don't mind that I shared the video also on facebook
That's fine Paul.
Logged

baz parkes

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1894
    • All Blacked Up
Re: Converting a two row to a one row
« Reply #37 on: February 20, 2020, 11:28:39 AM »

.
As I say, I've never played much on a one-row, and I've clocked up less than an hour of playing on this one...
but here's a wee tune.

Lovely...and also splendidly appropriate for Theme of the Month... :|glug
Logged
On the edge of Cheshire's Golden Triangle, apparently...

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Converting a two row to a one row
« Reply #38 on: February 20, 2020, 01:47:34 PM »

As I say, I've never played much on a one-row, and I've clocked up less than an hour of playing on this one...
but here's a wee tune.
That's a canny conversion. Well done! Lovely tune and brilliant playing.  (:)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Converting a two row to a one row
« Reply #39 on: February 20, 2020, 08:53:12 PM »

It was only last week that I eventually got around to installing the reeds.
I haven't fine tuned yet. Still mulling over the final sound I want to achieve.
Yesterday I repadded the pallets.
I've never owned a one-row before, mainly because I never really got on with the left-hand side on conventional ones. The very narrow space between the row of buttons and the outer edge of the fingerboard was always an issue for me as well.
On my 'homemade one', I have used a regular two-row fingerboard with the outer row holes sealed off.
Also, I wanted to have better left-hand chord options. For now, it's chords only; G/G, D/A, A/E, F#/B (minus thirds).
The action is not bad, but I think I can improve it further by tweaking the springs.
As I say, I've never played much on a one-row, and I've clocked up less than an hour of playing on this one...
but here's a wee tune.

Nice job! And playing!
I don’t see anything about what you used for reeds to make up the balance LM side.
Different box or were you able to use some of the leftovers?
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: 1 [2] 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal