Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: sticking key repair needs repair!  (Read 1011 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
sticking key repair needs repair!
« on: February 04, 2019, 08:24:20 PM »

I had a sluggish/sticking key on one of my one-row boxes. After eliminating other potential causes, I determined it was due to friction where the axle rod passes through the wooden key.  I removed the axle rod and discovered that the axle itself passed through a metal conduit which ran through all the keys and keyboard, but which had been cut so as to be sectioned-off for each key, etc.  The only key that didn't have the conduit was the one that was sticking, so I took a drill bit of the *exact* same diameter of the existing hole and simply passed it through using my fingers, rolling it as I went.  Well, it turned out to be too much, and while the sticking key is no longer a problem, the issue is that it now sits too loose on the axle!  I figured I was safe because I was using a drill bit that could already pass through the opening, and made sure not to use a power tool.  It sure didn't take much...

Fortunately, the instrument still plays fine, however the one key that is now a little loose results in a pallet that doesn't quite sit where I'd like it to.  I'd like to fix the issue, and the only solution I can see is to somehow reduce (marginally!) the hole in the key.  Any tips?
Logged
C#/D player

Broadland Boy

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1243
  • Awful noises from Pokerwork, HA114G, BbEb Liliputs
Re: sticking key repair needs repair!
« Reply #1 on: February 04, 2019, 08:35:19 PM »

Showing the hole steam from a kettle might relax any compression in the wood and tighten it back a bit
Logged
Richard A
Venit ventus contrarius ventus egrediente,
Omnes prope quid ventum est circa

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: sticking key repair needs repair!
« Reply #2 on: February 04, 2019, 10:20:35 PM »

What you describe as conduit sounds to me like a series of bearings (quite possibly cut from metal tube) . Do you have any idea what metal the axle and bearings are (respectively) made of?
Are we talking steel for the axle and brass for the tube?
Model shops supply drawn brass tube in a variety of diameters, manufactured to very close tolerances.. your best option may well be to provide a bearing tube for the key- but you will need to get your hands on a micrometer to ensure you get the right tube size.

A cruder but effective approach would be to cut (with sharp scissors) a small rectangle of aluminium from a drinks can- length  3 times the diameter of the axle, roll the aluminum round the axle to create a slit tube, insert the slit tube into the hole through the key and then push the axle in. If it is too tight remove the aluminium from the key hole, trim it so it doesn't wrap right the way round the axle and try again .

You might- depending on how little slack you need to take up- achieve a satisfactory result with a small piece of paper.

Peadar
« Last Edit: February 05, 2019, 12:25:40 AM by Peadar »
Logged

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: sticking key repair needs repair!
« Reply #3 on: February 05, 2019, 01:53:39 PM »

I believe it is steel for the axle and brass for the conduit.

I thought about making and inserting a conduit for that key as well, but I’ve decided to try filling the hole with wood glue and a toothpick (as a dowel), and then drill it out again. If it doesn’t work I’ll just be back where I started so no biggie there. I’ll let you know how it goes.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: sticking key repair needs repair!
« Reply #4 on: February 05, 2019, 02:05:25 PM »

Rather than wood glue I would use cyanoacrylate for this and instead of a toothpick use the axle rod itself .  One the glue has thoroughly cured a twist of the rid will free it..  Ive used this method many times to tighten up loose bellows pins.  If the result is a bit too tight just work the rod back and forth through the hole, or even spin it in a low speed drill.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1683
Re: sticking key repair needs repair!
« Reply #5 on: February 05, 2019, 06:24:03 PM »

Rather than wood glue I would use cyanoacrylate for this and instead of a toothpick use the axle rod itself .  One the glue has thoroughly cured a twist of the rid will free it..  Ive used this method many times to tighten up loose bellows pins.  If the result is a bit too tight just work the rod back and forth through the hole, or even spin it in a low speed drill.

Thanks for the suggestion, Theo. By the time I read this I had already carried out my proposed repair of filling in the hole and drilling it out again, which turned out to be successful. However, in future (or if this repair job doesn’t last for some reason) I will try your method.

I’m quite amazed at how little room for error there is in this!
Logged
C#/D player
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal