Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Erica D/G  (Read 4530 times)

0 Members and 1 Guest are viewing this topic.

Anne Croucher

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 203
Erica D/G
« on: February 06, 2019, 06:17:32 PM »

I have been playing this box - I could hear that all was not quite well, but it played, and although I could see that it had been mistreated - screws all different sizes in the grill, screws replacing bellows pins, silicon to fill up gaps - but I am to play for longsword at the end of the month and thought I would do up the poor thing.
I bought new bits a while ago now, and the cigarette smell has reduced a bit.
Plus - as has been announced, Gena Crisman has her new Oakwood, and as mother I got to drive to Leeds and then York to collect it, and then I listened to all the Castagnaris being played.

Opened up the treble end of the Erica to fit a new key board, the original being cracked. Peel off the silicon, remove the grill, remove the blue tac and the grotty fabric, then stare in astonishment at the bass end as I see that there are reeds bent out like the hopeful thumb of a hitchhiker.

Ah - maybe they did not work and were silenced but perhaps - if I can return them to normal they will make the odd lack go away. I took out the block, used a scalpel blade for support and restored the normal situation.

Removed the old keyboard, slid on the new one and realised that the buttons are not aligned with the holes. Remove keyboard and find set square - all the levers are bent over, some more than others. I used two pairs of fine nosed pliers to straighten them up to equal spacing and find that they are slightly too wide for the D row, G row looks fine now. Cup of coffee and will have another go soon.

Then I need to fill in the screw holes and remake them for the correct sized dainty screws or proper bellows pins, new gauze inside the grill, put new tape on half the bellows, new bellows gaskets, a really good clean inside and out, close up and fit the upgraded straps, and then see if it still plays.   

I tend to name things - this one might be called Dent - though not Arthur - right then - back to the pliers, hoping that the bellows tape was not put on with something permanent 
Logged
Barcarole D/G
Hohner Ericas D/G and C/F
Hohner el Rey del Vallenato A/D/G aka 'Elvis'
Hohner Liliput Bb/Eb club layout
Meinel & Herold G C F 3 voice 3 row 16 bass

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Erica D/G
« Reply #1 on: February 06, 2019, 07:46:25 PM »

If you need a bit of gauze for the grille I have some pieces of fine black material that are offcuts from a lightweight fly mesh curtain that will do the job. Black may be the wrong colour for your box of course.  ::)
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Erica D/G
« Reply #2 on: February 06, 2019, 11:29:47 PM »

Then I need to fill in the screw holes and remake them for the correct sized dainty screws or proper bellows pins,
Sounds like you are getting to grips with a great project box!

I would recommend bellows pins in preference to screws. During working on the box, revalving, tuning etc, you will have the ends on and off many times. Bellows pins are better than screws as the latter are more likely to wear out the threads in the screw holes with repeated disassembly and reassembly.
Hohner bellows pins are readily available from Charlie Marshall.
http://www.cgmmusical.co.uk/CGM_Musical_Services/Bellow_Pins.html   
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Anne Croucher

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 203
Re: Erica D/G
« Reply #3 on: February 07, 2019, 12:16:39 AM »

Bellows pins were obtained along with the new keyboard, which does now seem to be sitting correctly with the buttons all mid-hole.
The screws would be for the grille - which has polished up well, but needs a slight reshaping on one corner. The overly large and mismatched screws have enlarged the holes which hold it on - but washers should help there.

I have now got to put on new foam for the gasket - a final clean is required to remove the last of the glue and silicon.

The box was playable, which is why it has taken so long to get around to doing the work - though the two bent out reeds explain the oddities in the bass end. The keyboard end reeds seem fine, all were working and appear neatly valved.
Logged
Barcarole D/G
Hohner Ericas D/G and C/F
Hohner el Rey del Vallenato A/D/G aka 'Elvis'
Hohner Liliput Bb/Eb club layout
Meinel & Herold G C F 3 voice 3 row 16 bass

Anne Croucher

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 203
Re: Erica D/G
« Reply #4 on: February 07, 2019, 12:20:51 AM »

If you need a bit of gauze for the grille I have some pieces of fine black material that are offcuts from a lightweight fly mesh curtain that will do the job. Black may be the wrong colour for your box of course.  ::)

Thank you  for the offer but I have loads of gauze for the tutu making I hope to indulge in at various festivals this year - I have a choice of white, purple or green so far - though blue and pink could be options....
Logged
Barcarole D/G
Hohner Ericas D/G and C/F
Hohner el Rey del Vallenato A/D/G aka 'Elvis'
Hohner Liliput Bb/Eb club layout
Meinel & Herold G C F 3 voice 3 row 16 bass

Anne Croucher

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 203
Re: Erica D/G
« Reply #5 on: February 07, 2019, 12:59:17 PM »

Inside brushed to remove dust, light cleaning with white spirit to remove soiling, bellows gasket applied to the open end, wood filler and epoxy putty found for the enlarged bellows pin holes, grille polished and cleaned, curvature corrected as much as possible and some tiny screws found - maybe fill in the large holes in the wood for holding that too. Need washers so that the small screws can hold the grille securely even with enlarged holes.



 
Logged
Barcarole D/G
Hohner Ericas D/G and C/F
Hohner el Rey del Vallenato A/D/G aka 'Elvis'
Hohner Liliput Bb/Eb club layout
Meinel & Herold G C F 3 voice 3 row 16 bass

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Erica D/G
« Reply #6 on: February 07, 2019, 01:31:12 PM »

Before you cracked the seals, did you set up the nets to catch anything that might have leapt out and scurried away?

I must admit mum, I would have really enjoyed some pictures of the inside, pre-correction, especially those bass reeds, that all sounds quite bizarre! But, I'm really glad you've taking the plunge to poke around inside it though, I do hope it comes back a bit more ship shape. It was obvious the box needed a bit of TLC before peeking inside, but like you say, it was playable to start with - perhaps with the needed restorations done, the sky's the limit? Best of luck!

Also, don't let dad near it!
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Erica D/G
« Reply #7 on: February 07, 2019, 02:06:07 PM »

Mmmm. When I remake bellow pin holes I find it best to, fill the holes (I use cocktail sticks and pva), then remove the bellows gasket, refit the ends and redrill the holes through the casework into the bellows frames. This means that when the gasket is fitted the holes are slightly out of alignment until the gasket is compressed thus giving a good seal and additional friction to the bellows pins.

Anne Croucher

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 203
Re: Erica D/G
« Reply #8 on: February 07, 2019, 03:13:27 PM »

I am firmly in the matchstick and white glue camp myself - but see Gena's comment on the involvement of paterfamilias.
Having found that the epoxy putty was setting up far faster than I'd expected, I had no choice but to let it harden and then use a couple of small drills to open up the holes.
I had 1 mm and 2mm drills so I used the 1mm with the parts separate, then used the 2mm with the parts together and gasket compressed. The pins now hold the parts close than before  and there is a noticeable improvement in the air pressure - but one of the notes is 'huffing' so I will need to see why - it might have got a bit of the swarf caught in it. I tried to catch all of it, but something has happened, as it was sounding correctly before. However it is morris practice tonight so as the box is working I will leave any further poking until tomorrow, just reinstate the grille and sweep up all the bits of rubber, silicon and oddments of plastic which formed the 'seal' up to now.

 
Logged
Barcarole D/G
Hohner Ericas D/G and C/F
Hohner el Rey del Vallenato A/D/G aka 'Elvis'
Hohner Liliput Bb/Eb club layout
Meinel & Herold G C F 3 voice 3 row 16 bass

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Erica D/G
« Reply #9 on: February 07, 2019, 06:11:14 PM »


...stare in astonishment at the bass end as I see that there are reeds bent out like the hopeful thumb of a hitchhiker.
 - maybe they did not work and were silenced...
.. those bass reeds, that all sounds quite bizarre!

I don't think there is any great mystery. The bent reeds are the result of 'over enthusiastic' playing.
It's the result of what English players call "Thrashing".
Curving the bellows too vigorously has clipped some of the bass reeds.
As the OP says;
Quote
I could see that it had been mistreated
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Erica D/G
« Reply #10 on: February 07, 2019, 07:24:29 PM »

I don't think there is any great mystery. The bent reeds are the result of 'over enthusiastic' playing.
It's the result of what English players call "Thrashing".
Curving the bellows too vigorously has clipped some of the bass reeds.
I agree with you that the severely bent bass reeds as described by Anne are probably due to the reed tips catching on the bellows fold when abnormally tightly curved. It would have to be combined with a very large amplitude swing on the reeds though, in order to catch on the bellows fold in the first place - as you say, from 'over enthusiastic' playing :o . I've never known it happen on an Erica before.

Generally, if reeds are played excessively hard, all that usually happens is the gap at the tip of the tongue can be compromised and, worst case, can crack or break the reed. I've also come across reed plates 'blasted' out of the wax due to excessive bellows pressure, although the wax was probably old and brittle anyway.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Erica D/G
« Reply #11 on: February 07, 2019, 07:26:07 PM »

I've also come across reed plates 'blasted' out of the wax due to excessive bellows pressure.


I've seen this as well but it is, in my estimation, more likely to have been caused  by failed wax than excessive bellows pressure.

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Erica D/G
« Reply #12 on: February 07, 2019, 07:28:27 PM »

I've seen this as well but it is, in my estimation, more likely to have been caused  by failed wax than excessive bellows pressure.

Like I said - "although the wax was probably old and brittle anyway."
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Erica D/G
« Reply #13 on: February 07, 2019, 08:53:54 PM »


I tend to name things - this one might be called Dent - though not Arthur

Reminds me of the old joke...
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Erica D/G
« Reply #14 on: February 07, 2019, 10:21:58 PM »

I've also come across reed plates 'blasted' out of the wax due to excessive bellows pressure, although the wax was probably old and brittle anyway.

Destroying the bellows as a result of excessive bellows pressure (thrashing) is not uncommon I believe.
I seem to remember at least one member on here who 'boasted' about the number of bellows he got through
in a single year...and that was on one box! (I think I remember that correctly).


Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Erica D/G
« Reply #15 on: February 07, 2019, 10:37:55 PM »

I’m sceptical about that.  I’ve been repairing boxes for 15 years as a full time occupation and I can think of only one example of a bellows that was blown out by hard playing, and even that was combined with wear from many years of play.  Bellows are much more likely to die from wear produced by rubbing against belt buckles, zips,buttons and other hard clothing components.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Erica D/G
« Reply #16 on: February 08, 2019, 12:03:59 AM »

I’m sceptical about that. 

Fair enough. Maybe I had 'over-blown' the phenomenon. It's not something I've come across in my own experience.
I did manage to find this post though, which was the basis of my observation earlier.
I was paraphrasing earlier and may have been unfair to the guy. He doesn't actually say he busted several
sets of bellows in one year.
Logged

Pearse Rossa

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 723
Re: Erica D/G
« Reply #17 on: February 08, 2019, 01:28:00 AM »

I’m sceptical about that. 

Fair enough. Maybe I had 'over-blown' the phenomenon. It's not something I've come across in my own experience.
I did manage to find this post though, which was the basis of my observation earlier.
I was paraphrasing earlier and may have been unfair to the guy. He doesn't actually say he busted several
sets of bellows in one year.

Actually, on the same thread he went on to say this;

I've bought 5 sets of bellows from Igor about 2 years ago to replace on my main workhorse Saltarelles in the band and I have gone through 3 sets of them!  They're certainly not as strong as the Galassi ones I've had in the past - but are considerably cheaper to be fair.  I found that they began to go with bellows corners popping off much more readily than they have on my other bellows.

That's not to say that they're not good bellows ... on one of my much less thrashed boxes they are still in perfect nick and as airtight as you could wish.  If anything Igor's bellows are more flexible from new than Galassi ones ... but they are not as hard wearing.  I would recommend them for any application apart from hard regular gigging (or morris playing!)
Logged

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Erica D/G
« Reply #18 on: February 17, 2019, 09:26:04 PM »

A couple of bellows failures I have run into are bellows pulled out so far the corners came off ,and people playing in clubs/ hot weather where sweat dampened the bellows to the point that they caved in on the pull.
 Admittedly these were on piano accordions that are held against the body more.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

Anne Croucher

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 203
Re: Erica D/G
« Reply #19 on: February 19, 2019, 12:30:08 AM »

I reassembled 'Dent' to the extent of being playable, then next day drew out the new bellows pins and propped the new keyboard at more of an angle as the D row buttons were too low down.
Two of the new diminutive screws holding the grille on are actually not doing so, the putty set too fast, so I will redo those with something more leisurely, and probably put on some new cloth, but the results so far are very pleasing. The sound is very morris. I think that the two bent reeds just took the edge off the sound.
I still need to work on the bass end which is held on with ugly screws rather than proper pins, but I am enjoying the restored sound and have been playing lots of jigs.   
Logged
Barcarole D/G
Hohner Ericas D/G and C/F
Hohner el Rey del Vallenato A/D/G aka 'Elvis'
Hohner Liliput Bb/Eb club layout
Meinel & Herold G C F 3 voice 3 row 16 bass
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal