Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Enlarging the air hole in a Black Pearl II  (Read 5365 times)

0 Members and 1 Guest are viewing this topic.

nigelr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 526
Re: Enlarging the air hole in a Black Pearl II
« Reply #20 on: February 21, 2019, 08:22:23 AM »

Thanks for the observations.  Not at all as straightforward as I had first thought.

I noticed that if you almost push the button below the casing (like you can with pokerwork RH buttons, if it doesn't give you nightmares), you get vastly more air but it doesn't feel a natural position for the thumb.
That's exactly the situation I have with this box - pretty tricky to play the basses with your thumb rammed into the hole!

But uh, to the topic in hand, wow, that air button seems kinda awful! Like it's just opening up into the side of the box! I'm not sure you can even really make it much bigger in the direction you have the most space, because there's a reed block in the way - I think you can see the corner of it peeking around. You might be better off with a more aggressive solution.
My Dad, when confronted by a particularly tricky DIY or engineering problem, would tuck his pencil behind his ear and advise that this project needed "an extra coat of thinking".  I know what he meant.

I think I will investigate two aspects of this - making the hole slightly bigger by squaring off the edges and look at ways of amending the mechanism to lift the pallet away from the hole rather than hinge in a weird way.  Next instalment may not be until next week!
Logged
DB Oakwood Super 2 (D/G), Club II (D/G Will Allen layout), Erika (Bb/Eb) and an HA114 in C

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Enlarging the air hole in a Black Pearl II
« Reply #21 on: February 21, 2019, 09:00:58 AM »

Thanks for the observations.  Not at all as straightforward as I had first thought.

I think I will investigate two aspects of this - making the hole slightly bigger by squaring off the edges and look at ways of amending the mechanism to lift the pallet away from the hole rather than hinge in a weird way.  Next instalment may not be until next week!

I am sure there was a really interesting thread on the subject of applying a bit of science to air button design, a bit back to give a more usable air gradient. Trouble is, I can't find it. Anyone remember?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Enlarging the air hole in a Black Pearl II
« Reply #22 on: February 21, 2019, 09:08:43 AM »

A few years ago I did some tuning work on a Black Pearl 3 and took some photos of the bass end pallets and reed blocks layout.

Looking at the photos again, I notice that it has an unusual air button mechanism which I didn't take too much notice of at the time, as there was nothing wrong with it and it seemed to work perfectly well.

But the rod from the lever type air button goes through the air hole in the fondo and pushes on the pallet* on the felt/leather facing material (see photo 1 towards the upper right). The pallet and hinge are on the other side of the fondo, on the side which has the reed blocks (see photo 2). There seems to be more room here for the mechanism.

Would there be scope for redesigning the OP's air button along these lines, I wonder?

Edit:
*Just realised that the mechanism is similar to yours, Gena, and your photos are more specific too.
http://forum.melodeon.net/index.php/topic,23543.msg280624.html#msg280624
« Last Edit: February 21, 2019, 09:22:48 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Enlarging the air hole in a Black Pearl II
« Reply #23 on: February 21, 2019, 09:10:52 AM »

Looking at Google images, I think it's an Oakwood super III
Playing with MM and the thirds out, the air button is OK. Trying to re-enact the white heather club with all stops out I was struggling.
I've just acquired a Hohner club 2b to butcher and even though it's in a bit of a state, the air management is superb. The flap is humongous.
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

nigelr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 526
Re: Enlarging the air hole in a Black Pearl II
« Reply #24 on: February 21, 2019, 10:01:02 AM »

But the rod from the lever type air button goes through the air hole in the fondo and pushes on the pallet* on the felt/leather facing material (see photo 1 towards the upper right). The pallet and hinge are on the other side of the fondo, on the side which has the reed blocks (see photo 2). There seems to be more room here for the mechanism.

Would there be scope for redesigning the OP's air button along these lines, I wonder?

Edit:
*Just realised that the mechanism is similar to yours, Gena, and your photos are more specific too.
http://forum.melodeon.net/index.php/topic,23543.msg280624.html#msg280624
Yes, that's how it is on my Oakwood Super 2 (and Gena's newer Black Pearl) and it works like a dream.  I fear that to replicate this on the BPII would constitute major surgery and would be beyond my capabilities.  Also, as has been spotted by others as well, the bass reed block is visible through the air hole so would be in the way if I were to try this approach.
« Last Edit: February 21, 2019, 10:21:42 AM by nigelr »
Logged
DB Oakwood Super 2 (D/G), Club II (D/G Will Allen layout), Erika (Bb/Eb) and an HA114 in C

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Enlarging the air hole in a Black Pearl II
« Reply #25 on: February 21, 2019, 10:34:24 AM »

Also, as has been spotted by others as well, the bass reed block is visible through the air hole so would be in the way if I were to try this approach.
This also explains why there is a short bass reed block mounted vertically in my photo 2. It allows more room for the air button pallet and mechanism. 


In yours, the bass reed block is also restricting the air flow through the air hole. Perhaps your best approach for now would be to enlarge the air hole within the confines of your existing pallet contact footprint by enlarging it to the right ('up' in your photo thumbnail; the photo roatates when downloaded!) as much as you can without creating a leak at the pallet long edge. You could achieve perhaps another 15 - 20% cross-sectional area that way, which might make all the difference to getting a useable air flow.
« Last Edit: February 21, 2019, 10:45:21 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

nigelr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 526
Re: Enlarging the air hole in a Black Pearl II
« Reply #26 on: February 21, 2019, 10:42:12 AM »

Also, as has been spotted by others as well, the bass reed block is visible through the air hole so would be in the way if I were to try this approach.
This also explains why there is a short bass reed block mounted vertically in my photo 2. It allows more room for the air button pallet and mechanism.
Oh yes, I didn't fully appreciate that when I looked at them first time.  Thank you.  DB appear to have completely redesigned the bass end at some stage!
Logged
DB Oakwood Super 2 (D/G), Club II (D/G Will Allen layout), Erika (Bb/Eb) and an HA114 in C

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Enlarging the air hole in a Black Pearl II
« Reply #27 on: February 21, 2019, 01:57:49 PM »

I guess that's where the 4 note chords comes from.

So, in those bp3 pictures, the bellows frame is responsible for the internal air button being so far from the edge and interrupting the flat bass block - it cant be closer to the edge on the inside as it will bump into it. If that's how they liked go make things, then, Nigel's instrument may also have a flat block, which means the space that seems free above the nearby pallet, isn't.

Seems like a fun puzzle! I think one option would be to remove the pallet and adjust the existing arm to relocate the position away from the bass block area a little, and let you enlarge the hole in that direction. Failing that, I do have a couple of more barmy ideas, like seeing if you can change the existing mechanism so the spring was on the other side of the pivot, giving you the option to remove part of the existing plate and free up more space for a pallet.
Logged

nigelr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 526
Re: Enlarging the air hole in a Black Pearl II
« Reply #28 on: February 21, 2019, 03:14:42 PM »

In yours, the bass reed block is also restricting the air flow through the air hole. Perhaps your best approach for now would be to enlarge the air hole within the confines of your existing pallet contact footprint by enlarging it to the right ('up' in your photo thumbnail; the photo roatates when downloaded!) as much as you can without creating a leak at the pallet long edge. You could achieve perhaps another 15 - 20% cross-sectional area that way, which might make all the difference to getting a useable air flow.
I think I am going to try this first and see what the improvement is.  If it's still sluggish then I'll look at the pivot mechanism to see if the pallet can be lifted further off the hole rather than just the hinge on one edge.

Seems like a fun puzzle! I think one option would be to remove the pallet and adjust the existing arm to relocate the position away from the bass block area a little, and let you enlarge the hole in that direction. Failing that, I do have a couple of more barmy ideas, like seeing if you can change the existing mechanism so the spring was on the other side of the pivot, giving you the option to remove part of the existing plate and free up more space for a pallet.
Always up for ideas, barmy or not  (:)
Logged
DB Oakwood Super 2 (D/G), Club II (D/G Will Allen layout), Erika (Bb/Eb) and an HA114 in C

playandteach

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3526
  • Currently a music teacher in a high school.
Re: Enlarging the air hole in a Black Pearl II
« Reply #29 on: February 21, 2019, 03:17:28 PM »

I think the modification was about air-flow using a wedge to make it more linear.
http://forum.melodeon.net/index.php/topic,20966.msg251846.html#msg251846
Logged
Serafini R2D2 GC, Serafini GC accs 18 bass

Tone Dumb Greg

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4955
    • Dartmoor Border Morris
Re: Enlarging the air hole in a Black Pearl II
« Reply #30 on: February 21, 2019, 03:39:44 PM »

I think the modification was about air-flow using a wedge to make it more linear.
http://forum.melodeon.net/index.php/topic,20966.msg251846.html#msg251846

Yes. Maybe this could be seen as an opportunity, not a problem?
Logged
Greg Smith
DG/GC Pokerwork, DG 2.4 Saltarelle, pre-war CF Hohner, Hohner 1040 Vienna style, old  BbEb Hohner that needs a lot of work.

ACCORDION, n. An instrument in harmony with the sentiments of an assassin. Ambrose Bierce

nigelr

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 526
Re: Enlarging the air hole in a Black Pearl II
« Reply #31 on: March 04, 2019, 07:36:13 PM »

I've now completed the work on this project for now.  The attached pictures show:

- the bass reed configuration - which is why I can't mimic the mechanism as per the newer BPII's and the Oakwood Super 2
- the overlap of the bass reed block;
- the "trimming" of the reed block.  There is plenty of wood at the end that doesn't interfere with the felt around the holes so I had scope to do this;
- the enlarged hole by squaring off the edges at one end;

I also bent the wire that is pushed by the air button very slightly upwards to ensure more movement in the pivot.

By removing the reed block interference, making the hole slightly larger and bending the wire, there has been a great improvement in the air flow.  It's not as responsive as the Super 2 but is much much better and I can ride the air button and nudge it with much more control.

Here is a tune with it as a test run once I'd finished the work.  Overall I'm happy that my meagre DIY skills have allowed me to give this box a new lease of life.
 
https://youtu.be/oCDrs2P6ULg
Logged
DB Oakwood Super 2 (D/G), Club II (D/G Will Allen layout), Erika (Bb/Eb) and an HA114 in C

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Enlarging the air hole in a Black Pearl II
« Reply #32 on: March 09, 2019, 06:31:30 PM »

Based on air flow behavior that i know from working with steam and jet engines, you can remarkably increase airflow by just rounding sharp edges on air passages. Gains can be in the range of 30%.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal