Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: spring strength/ button pressure  (Read 1536 times)

0 Members and 1 Guest are viewing this topic.

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
spring strength/ button pressure
« on: February 21, 2019, 01:52:57 PM »

Sorry if this has been covered elswhere, but does any one have a chart of comparative key weights, the pressure needed to open a treble button, on various makes of melodeon? Or just weights for one specific model? I am at the stage of making and fitting the springs in my home made instrument, and have only my Saltarelle and a couple of old clubs to compare. Many thanks, Dave
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: spring strength/ button pressure
« Reply #1 on: February 21, 2019, 05:56:04 PM »

How do you propose to measure, to obtain comparable results?
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: spring strength/ button pressure
« Reply #2 on: February 21, 2019, 06:02:36 PM »

How do you propose to measure, to obtain comparable results?


I have used a 'electronic drug dealer scale' to measure/set up button pressure, quite a faff.

benammiswift

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 158
  • Squeezing for Derbyshire
    • benammiswift.co.uk
Re: spring strength/ button pressure
« Reply #3 on: February 21, 2019, 06:58:24 PM »

It's down to much more than just spring strength because if you want to lighten the action you can change the spring which makes it less airtight.

You can lighten the button pressure by modifying the design to add length on the Button side of the action, this would reduce button pressure without affecting airtightness. So it's not really comparible to just measure button weight.

Also there's different action, especially on a Three Row. my Castagnari Mas has all L shaped rockers where the Handry 18 for the third row uses a very different system which lifts and independent action. I've heard it called compound action and simple.

So there's a lot to affect it that isn't the springs
Logged
Castagnari Handry 18

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: spring strength/ button pressure
« Reply #4 on: February 21, 2019, 09:37:12 PM »

Hi All, Thanks for replies.
I am checking the force using a dynamometer. An old analogue one for testing I know not what, but it reads out in gramms, and works in the range I need. There seem to be two distinct values. One to start the button moving, and another to complete most or all of it travel.
My findings so far show me a not insignificant difference between my Saltatelle, and my Club 3B, which is the lighter touch of the two, and shows no pallet leakage even under quite a bit of force on the bellows.
As to the key length, well not having designed one before, I have tried to use as near to the Castagnari Mory sizes for most bits, since that is the instrument I am emulating. My action is all wooden though, so although key shaft/pallet rod ratio is much the same, it is quite a different action. My design permits the springs to be removed and replaced without too much faff, so if having finished it I need to weaken or strengthen them, I can. Having taken 6 months to finish the keyboard, I very much doubt that I will re-design it!
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.

Dave Praties

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 195
Re: spring strength/ button pressure
« Reply #5 on: February 26, 2019, 05:59:23 PM »

All springs now calculated and made, a few fitted, the rest going in tonight. Very exciting! All well so far so I thought I would post a pic of the emerging keyboard. I designed it to make changing or altering of the springs relatively easy once the instrument is together. All keys can also be withdrawn from the back of the keyboard having detached it from the fondo (?) is that the correct word? and un-coupled the register levers.
Soon will be wanting bellows. Does any one have a contact,(non-eBay), for the Slovenian maker? I can't seem to find him. Cheers, Dave
Logged
Castagnari Handry 18 G/C. Castagnari Handry 18 D/G.    Self-built G/C 2.5/12 bass. almost finished after 7 years! Bb/Eb Preciosa. C/F Lilliput.
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal