Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2   Go Down

Author Topic: Broken pallet arm  (Read 2804 times)

0 Members and 1 Guest are viewing this topic.

mselic

  • Hero Member
  • *****
  • Online Online
  • Posts: 1683
Broken pallet arm
« on: March 10, 2019, 03:24:45 AM »

Hmmmm...so while playing a box earlier this evening, one of the pallet arms simply broke off flush at the point where it screws into the wooden key.. I can only assume that there was some inherent weakness or flaw in the metal rod itself, as I don’t understand what would have caused it to fail. It certainly wasn’t under any undue stress while I was playing it. None of the other pallet arms show any sign of fragility or weakness (nor did this one, mind you, before it failed).

????!!

As far as I can tell, I have no option but to extract the remaining piece of rod from the wooden key and then built a new pallet arm to replace it. What are the pallet arms in these one-rows usually made from, and is there anywhere I can get my hands on some? I would have to build a jig to bend the new rod to match the remaining pallet arms, and then also find a way to flatten the end where the screws fasten to the pallet. I’m still puzzled as to why it failed in the first place...
« Last Edit: March 10, 2019, 03:26:30 AM by mselic »
Logged
C#/D player

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Broken pallet arm
« Reply #1 on: March 10, 2019, 07:50:31 AM »

Paging Rees Wesson, he went through a number of versions of pallet arms I seem to remember from way back. He may well be able to supply you with a replacement

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Broken pallet arm
« Reply #2 on: March 10, 2019, 09:00:16 AM »

Here I am. That pallet arm is aluminium, mine are made of steel.
It should be easy enough to make a new one if you can find the correct gauge aluminium (aluminium welding rod?)
Getting the broken piece out of the wooden lever will be a challenge as it looks to be threaded.

To make a new arm, flatten the end with a hammer on a small anvil and then drill the two screw holes.
Wire bending jigs are available on eBay.
I don't thread my pallet arms. I push them through the wooden lever then flatten the end a small amount, coat it in Araldite and hammer it back into the wooden lever.
Final adjustments can be made once the glue has set.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Broken pallet arm
« Reply #3 on: March 10, 2019, 09:52:23 AM »

I wonder if it's possible that the threaded portion of the aluminium arm has been part of the reason for its failure? Creating the thread has made the rod fractionally narrower in the core of the threaded portion. Also, as the photo shows, some of the threaded portion was never encased in the wooden part of the lever, so the assembly is inherently weaker at that point. :(

Good luck with the repair!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Broken pallet arm
« Reply #4 on: March 10, 2019, 10:29:03 AM »

mselic, I wonder if you'd be so kind as to tell us who made the instrument? I ask, hoping that we might be forewarned, as in "forewarned being forearmed"!

On closer inspection of the blown up picture, I would hate to have paid good money for such (IMHO) a poor quality of workmanship, and you all know that I'm no perfectionist!

The holes in the fondo are simply shocking! There is even a patch between two of the visible holes. (On seeing the mess, I couldn't help but recall a post from someone recently about nicely rounded off corners being helpful with airflow etc. haha!) The screws in the pallets appear to be countersunk, but the rods aren't. Heaven only knows what else is sub-standard in the rest of the construction.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Broken pallet arm
« Reply #5 on: March 10, 2019, 11:01:13 AM »

Getting back on topic ...

There is an alternative to extracting the remains of the broken pallet arm, and that is to make a new wooden button lever.  You will have to remove the wooden lever anway to extract the broken rod, so you will see that the arm is a simple rectangle.  It’s critical dimensions are the thickness of the lever, and the position and size of the hole for the axle rod.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Broken pallet arm
« Reply #6 on: March 10, 2019, 11:41:13 AM »

Theo, if you were doing that how would you approach it? I'm thinking I’d get the arm cut roughly to size, then drill the hole, then fine tune the arm so you know the hole is in *exactly* the right place, and it is exactly the right width... (or would I drill the hole and get exactly the correct width..*then* fine tune the top and bottom) ..But I’ve not made a new arm before...

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Broken pallet arm
« Reply #7 on: March 10, 2019, 12:24:36 PM »

I would use the old one as a pattern. That way you can't go wrong. You even have the broken rod as a pattern so you can match the degree of offset for that. Only thing  that would concern me is whether or not to duplicate the screw in method of fixing.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Broken pallet arm
« Reply #8 on: March 10, 2019, 12:36:50 PM »

I’d do as John describes.  You can even use the hole in the old lever to mark the position of the new hole. 
Two refinements:
1 measure the thickness of the old arm very accurately,  using digital callipers. Cut the new one a little over size and sand to final thickness.
2 drill the hole slightly underside, then ream out gradually. It’s critical that the lever moves freely on the axle rod, but with zero clearance, or as near zero as you can get. You can improvise a reamer in a couple of ways.  A twist drill held in the fingers is one, a piece of steel rod, eg piano wire with the surface roughened on abrasive paper is another.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

mselic

  • Hero Member
  • *****
  • Online Online
  • Posts: 1683
Re: Broken pallet arm
« Reply #9 on: March 10, 2019, 01:22:05 PM »

mselic, I wonder if you'd be so kind as to tell us who made the instrument? I ask, hoping that we might be forewarned, as in "forewarned being forearmed"!

On closer inspection of the blown up picture, I would hate to have paid good money for such (IMHO) a poor quality of workmanship, and you all know that I'm no perfectionist!

The holes in the fondo are simply shocking! There is even a patch between two of the visible holes. (On seeing the mess, I couldn't help but recall a post from someone recently about nicely rounded off corners being helpful with airflow etc. haha!) The screws in the pallets appear to be countersunk, but the rods aren't. Heaven only knows what else is sub-standard in the rest of the construction.

I intentionally withheld the name of the maker as I did not want to invite criticism.  The maker of this box happens to be well-known and highly respected, currently building some of the nicest one-rows out there, and this just happens to be a very early example of his work.  In his own words he had said that they had come a long way since this one.  His workmanship today is second to none.  It also plays very nicely and happens to be one of my favourite-looking boxes, but I'm not going to share a photo now for the reasons I just gave.

The routed-out channel that you see between the two (MM) holes is pretty standard on most hand-made one-rows that I've seen, and facilitates better sound projection/volume from the part of the box that gets the smallest amount of pallet lift.  In a sense, they are sharing part of the same sound hole.
« Last Edit: March 10, 2019, 01:24:18 PM by mselic »
Logged
C#/D player

mselic

  • Hero Member
  • *****
  • Online Online
  • Posts: 1683
Re: Broken pallet arm
« Reply #10 on: March 10, 2019, 01:35:30 PM »

Getting back on topic ...

There is an alternative to extracting the remains of the broken pallet arm, and that is to make a new wooden button lever.  You will have to remove the wooden lever anway to extract the broken rod, so you will see that the arm is a simple rectangle.  It’s critical dimensions are the thickness of the lever, and the position and size of the hole for the axle rod.

I would have thought that using a screw extractor would have been a fairly straightforward approach to removing the remaining piece of rod?  I could then fill and re-drill the hole to accept a newly threaded rod (or a rod inserted as described by Rees).  Building a new key would require me to try and colour-match with stain and finish, etc.  I'd like to keep this as close to original as possible.

I wonder if it's possible that the threaded portion of the aluminium arm has been part of the reason for its failure? Creating the thread has made the rod fractionally narrower in the core of the threaded portion. Also, as the photo shows, some of the threaded portion was never encased in the wooden part of the lever, so the assembly is inherently weaker at that point. :(

It's quite possible, although I wouldn't have thought that that would actually compromise the integrity of the rod.  I wonder if it wasn't damaged at the time of threading in some way that didn't manifest until several decades later!

Here I am. That pallet arm is aluminium, mine are made of steel.
It should be easy enough to make a new one if you can find the correct gauge aluminium (aluminium welding rod?)
Getting the broken piece out of the wooden lever will be a challenge as it looks to be threaded.

To make a new arm, flatten the end with a hammer on a small anvil and then drill the two screw holes.
Wire bending jigs are available on eBay.
I don't thread my pallet arms. I push them through the wooden lever then flatten the end a small amount, coat it in Araldite and hammer it back into the wooden lever.
Final adjustments can be made once the glue has set.

Thanks, Rees. I'm sure it would be easier to make my own jig? I'd have to customize it to bend the rod so that it matched the remaining pallet arms.
Logged
C#/D player

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Broken pallet arm
« Reply #11 on: March 10, 2019, 02:08:16 PM »


I would have thought that using a screw extractor would have been a fairly straightforward approach to removing the remaining piece of rod?  I could then fill and re-drill the hole to accept a newly threaded rod (or a rod inserted as described by Rees).  Building a new key would require me to try and colour-match with stain and finish, etc.  I'd like to keep this as close to original as possible.

Yes that would be my first choice too, but if the screw doesn't want to come out you have a plan B.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Broken pallet arm
« Reply #12 on: March 10, 2019, 04:09:23 PM »

Getting back on topic ...

There is an alternative to extracting the remains of the broken pallet arm, and that is to make a new wooden button lever.  You will have to remove the wooden lever anway to extract the broken rod, so you will see that the arm is a simple rectangle.  It’s critical dimensions are the thickness of the lever, and the position and size of the hole for the axle rod.
Just to note the piece you will need is not quite simple in shape if you do plan B.
The lever is notched so that the face plate can span over it ( yours looks like that ?), and when I made a set for a one row I was working on it also needed a taper on the back. When I made them I laid out the dimensions of side veiw with notch and taper  on the edge grain of wood, cut this out , then slice to size needed to fit finger board then I would do as Theo suggested use the one you took out to mark for drilling or hold in position relative to others then slide in the rod till it hits ,this should leave a mark.
When making the piece I cut extra profile pieces if you had dimensions and a picture of the part I could see how close mine is to yours. ( there are not cut to width of the groove yet )

Edit to add photo.
Piece before slicing to fit slot in the finger bd.
« Last Edit: March 10, 2019, 04:41:08 PM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

JD

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 235
Re: Broken pallet arm
« Reply #13 on: March 10, 2019, 04:15:42 PM »

Have you tried contacting the maker of the box. He might have a few parts left over from earlier models and might be happy to send them to you. That would only leave the fitting and adjusting. Only!


Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Broken pallet arm
« Reply #14 on: March 10, 2019, 04:53:04 PM »

“What are the pallet arms in these one-rows usually made from, and is there anywhere I can get my hands on some?”


Your finger bd. Looks like cherry and I wouldn’t think you would need any different for the lever.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Broken pallet arm
« Reply #15 on: March 10, 2019, 05:21:24 PM »

Or might be beech or maple.  Both a bit harder than cherry, and may wear better.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Broken pallet arm
« Reply #16 on: March 10, 2019, 05:58:32 PM »

I agree they are harder and harder to work with too!
and then there's the stability of wood, as you don't want to much twist/ movement in this piece as we all know to well.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Broken pallet arm
« Reply #17 on: March 10, 2019, 06:03:46 PM »

Indeed, so whatever the timber it should be well seasoned.  Something reclaimed from an old piece of furniture would be good.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Broken pallet arm
« Reply #18 on: March 10, 2019, 06:32:56 PM »

Yes for sure ,
The reason I choose cherry is when seasoning it shrinks very little also it does not twist/ warp much and is very stable there after.

Roy Underhill, The woodwright shop
Says  for black or wild cherry trees
“Along with its stability and strength, makes it prized for high quality work in furniture,
Scientific instruments, sculpture.”

Also if you read the book you will know you I need to read the back/grain not all trees grow straight.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Broken pallet arm
« Reply #19 on: March 11, 2019, 01:30:38 AM »

Reason for failure- If the rod is threaded it is not so much the thinning of the rod at the root of the threads but the fact that a notch i.e. the root of the thread acts as a local stress raiser. Add to that the fact that unlike ferrous  metals aluminium does not have a lower fatigue limit -  if metals are subject to cyclic stress they fatigue and eventually cracks develop and breakage eventually follows. If the stresses are low it will take hundreds of thousands of cycles but it will happen - except for ferrous metals which have a lower fatigue limit- i.e. if stresses stay below this limit they can function "forever".

This is why (aluminum) airframes have a service life measured in hours but (steel) railway locomotive main frames don't. Rails on the other hand suffer very high contact stresses and sometimes break before they wear out.

Logged
Pages: [1] 2   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal