Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2] 3 4 5 6 7 ... 13   Go Down

Author Topic: Building a one row four stop  (Read 47409 times)

0 Members and 2 Guests are viewing this topic.

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #20 on: May 03, 2019, 02:56:22 AM »

Firewood is piling up!! The standing reed block is giving me fits, I thought I had it figured out ( my second attempt) the right base width , chamber size and depth , taper ,etc. . Only to realize my mistake, its a** backward. Well it would work well for a lefty box.

I’m sure I’ll be told to scrap it, but could you do MLMH stop setup instead of MMLH.  Would it make a difference in sound?
The box is for me so I don’t mind if the banks are not quite traditional ::), as long as the sound is good.

Ugh can’t believe I didn’t invert it, I was so focused on the little bits I forgot to step back and look at the whole.
« Last Edit: May 03, 2019, 03:01:19 AM by boxcall »
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Building a one row four stop
« Reply #21 on: May 03, 2019, 03:53:12 AM »

Scrap it !  (well you asked for it, didn't you ?  ;) )

I assume the L row is in its usual place to benefit from increased pallet lift there. It may suffer marginally from being closer to the keyboard (and the upright M may benefit) but if the block is otherwise OK, you may as well use it.

It's possible to improve airflow on the back reeds by filing away part of the plate under the pallets (it's a Mélodie in the picture).

And the stops won't be in their usual place...

 
Logged

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Building a one row four stop
« Reply #22 on: May 03, 2019, 09:17:27 AM »

I made exactly the same mistake on the first one-row that I built 12 years ago, so it ended up as MLMH.
It worked fine and is still being played today. The change made no difference to the sound.
I've since made another 27 with the reed blocks in the correct order!
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #23 on: May 03, 2019, 08:54:38 PM »

Scrap it !  (well you asked for it, didn't you ?  ;) )

I assume the L row is in its usual place to benefit from increased pallet lift there. It may suffer marginally from being closer to the keyboard (and the upright M may benefit) butif the block is otherwise OK, you may as well use it.

It's possible to improve airflow on the back reeds by filing away part of the plate under the pallets (it's a Mélodie in the picture).

And the stops won't be in their usual place...
I thought about the air flow and stop position , I could do no stops,  then who would know ;)
As for air flow I would agree that it would be greater away from keyboard, but then wonder why is the small reed bank out front? for that reason. but I suspect it’s more to do with fit / layout, which is quite tight I’m finding out.

I made exactly the same mistake on the first one-row that I built 12 years ago, so it ended up as MLMH.
It worked fine and is still being played today. The change made no difference to the sound.
I've since made another 27 with the reed blocks in the correct order!

Thanks Rees, good to know it could be used and that it does happen :|bl
Maybe a new thread? What not to do and common problems when building a melodeon (:)

I’m also seeing a problem with the spacing, the reed block being slightly different than the fondo holes which are 19mm apart or 3/4”. So reed being 5/8” wide or 15.875mm I made the chamber 9/16” /14.288mm and the divider 3/16” / 4.763mm all equaling 19mm / 3/4”. For some reason the holes in the reedblock get closer to the edge of chamber as you move from “good in the middle” to each end.
Nothing goes beyond the edge of a hole, but the chambers are not all centered over the holes.
I must be off fractionally on either the chamber size or the dividers, one or both should be bigger.
I put the reeds in the block and its snug, but I do have a margin along the valve.

Do my numbers look off?

My problem could be (well new glasses for one) I was using 16th of an inch, I could have gone finer maybe. I could use better lighting in the tool shed also and or a sharper pencil!!








Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #24 on: May 04, 2019, 05:47:35 PM »

Fondo sample a member sent me to trial fit, I think it looks good enough to use!
Fits great.
Thank you!! Howard
It was nice to see this in the mail box after I got back from kicking myself around the block for screwing up the reed block ;)
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #25 on: May 06, 2019, 09:37:34 PM »

"oops I did it again" ..the right way round ;)

I made the center divider out of a solid piece of cherry, I also made the chambers slightly bigger in width so they line up better.
The flat blocks although they could use a fraction on the chamber, I think I can use them.

I'm probably boring you all to death, if so sorry.

Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Building a one row four stop
« Reply #26 on: May 06, 2019, 09:42:49 PM »

Definitely interesting  (:)
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Stockaryd

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 255
Re: Building a one row four stop
« Reply #27 on: May 06, 2019, 09:46:51 PM »


 . .   and I read every bit of it. 
Logged
Hohner Corso, Hohner Erica, Emmanuel Pariselle, Gessner,   Koch,   Mariotti,    "China  NoName",   4 Toy,     -and now some more

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #28 on: May 07, 2019, 03:35:54 AM »


 . .   and I read every bit of it. 
  (:)



So I’m getting a head of myself but wondering about something. So as most of you know there's not much room for things inside the box side to side or front to back. The middle reed block reeds are tight up to the base of the flat reed block, almost no room for waxing at the big reed end.

So question is, what’s done here?
On my Beltuna it appears that there is no wax along the bottom of reeds in the stand up block, wax can be seen clearly along top and edges, I’m not sure how that would seal properly.  Unless there is a gasket at the base or the reed plate base was dipped in hot wax then placed? If so I would expect a little squeeze out of wax.

Anyone know..



Ps just wanted to add when cutting the new standing block divider I used a Japanese carpenter
saw running on guide boards that were clamp to it. Ripping it on its compound angle.
The saw I have (well one of them) has got a crosscut side and ripping side and a large flat blade that works great for laying up tight to runners for cutting.
I don’t know what I did before I got my hands on one of these saws!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Building a one row four stop
« Reply #29 on: May 07, 2019, 10:17:48 AM »

So I’m getting a head of myself but wondering about something. So as most of you know there's not much room for things inside the box side to side or front to back. The middle reed block reeds are tight up to the base of the flat reed block, almost no room for waxing at the big reed end.

So question is, what’s done here?
On my Beltuna it appears that there is no wax along the bottom of reeds in the stand up block, wax can be seen clearly along top and edges, I’m not sure how that would seal properly.  Unless there is a gasket at the base or the reed plate base was dipped in hot wax then placed? If so I would expect a little squeeze out of wax.

Anyone know..
Don't use wax. Fix the reed plates in place by screws on a gasket of olivisc. The screw heads hold the reed plates down on to the gasket. Pre-drill the screw holes first.

It's standard practice for many one-row builds. You will get a better sound too, as the reed plates are held more rigidly to the reed blocks than wax normally allows.

Photos are of the reed blocks in my Wesson Clipper (a superb instrument - thanks Rees!)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Building a one row four stop
« Reply #30 on: May 07, 2019, 10:51:32 AM »

Yes go with screwed down reed plates.  The special large headed screws are available from Carini.  Let me know if you can't find them and I'll dig out the part numbers.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #31 on: May 07, 2019, 03:12:12 PM »

Thank you both,
I’ll take another look at the Carini site, I was looking for other parts and could not make my way around to easy.

My concern with screws is do I have the correct spacing between plates, wax is more forgiving there I think, but I like the idea of the gasket.

Wouldn’t it be nice if melodeon build kits were available with all the parts gather up for you, hint hint.
You could have a couple of choices like button color, and etc. to make it your own.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

rees

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 5055
  • Windjammer
    • Wesson Accordions
Re: Building a one row four stop
« Reply #32 on: May 07, 2019, 04:24:21 PM »

Thank you both,
I’ll take another look at the Carini site, I was looking for other parts and could not make my way around to easy.

My concern with screws is do I have the correct spacing between plates, wax is more forgiving there I think, but I like the idea of the gasket.

Wouldn’t it be nice if melodeon build kits were available with all the parts gather up for you, hint hint.
You could have a couple of choices like button color, and etc. to make it your own.

If the spacing is too wide you could use washers on the screws.
Logged
Rees Wesson (accordion builder and mechanic)
Gungrog, Welshpool, Wales, UK
www.melodeons.com

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Building a one row four stop
« Reply #33 on: May 07, 2019, 04:50:58 PM »

Wouldn’t it be nice if melodeon build kits were available with all the parts gather up for you, hint hint.
You could have a couple of choices like button color, and etc. to make it your own.
That's sort of what happens with Emmanuel Pariselle's melodeon building courses. It's not quite like assembling a kit of parts in that there is some cutting, shaping and sanding (and very much more sanding!) and drilling of the wood parts before fixing it all together. But the reeds, bellows, buttons, pallets and pallet arms are all pre-made, ready and waiting.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Building a one row four stop
« Reply #34 on: May 07, 2019, 05:38:15 PM »

It's possible, if a bit awkward, to get wax in the channels at the foot of the standing block using a soldering iron fitted with an extension (made from a length of copper wire) as visible at right in the attached picture.

Probably it's child's play for an artist of the spoon to pour wax in there for 2-3 reed plates, fit the plates before the wax hardens, and repeat.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Building a one row four stop
« Reply #35 on: May 07, 2019, 05:43:55 PM »

Apply wax to the end of the reed plate, and then press into place while the wax is still soft.

Simples!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #36 on: May 07, 2019, 05:47:26 PM »

Wouldn’t it be nice if melodeon build kits were available with all the parts gather up for you, hint hint.
You could have a couple of choices like button color, and etc. to make it your own.
That's sort of what happens with Emmanuel Pariselle's melodeon building courses. It's not quite like assembling a kit of parts in that there is some cutting, shaping and sanding (and very much more sanding!) and drilling of the wood parts before fixing it all together. But the reeds, bellows, buttons, pallets and pallet arms are all pre-made, ready and waiting.
I'd love to do the course but it would be to costly for me at the moment, I'm sure I could learn some things , meet nice people and get a nice box when completed.

I'm trying to contact Martin accordions, his daughter sells parts but has not sent me her email.
I figured they would have the stuff save me from getting a piece here and a piece there. I'm not into window shopping >:E
yes a kit would be nice! (:)

sanding and shaping.... I been doing a fair amount of that!
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #37 on: May 07, 2019, 05:51:17 PM »

Apply wax to the end of the reed plate, and then press into place while the wax is still soft.

Simples!
kinda what I was thinking if I go the wax route.

I like simple (:)

I still like to know what Beltuna did, maybe wax is there under the plate but I don't see any runout.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Building a one row four stop
« Reply #38 on: May 07, 2019, 06:16:41 PM »

Quote
Apply wax to the end of the reed plate, and then press into place while the wax is still soft.

Simple indeed !  Too late for me this time, but I'll try it for the next project.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Building a one row four stop
« Reply #39 on: May 07, 2019, 09:16:28 PM »

Recycle anyone ?
I prefer when possible I’m pretty sure this would be a little to heavy, requiring a large hole in the lever, but I had to try it on an extra lever. It has a built in flat and almost the same angle as my beltuna. I got a pile of them to choose from ;)
Paint can openers if anyone doesn’t know.
If the metal was a little thinner it would work with a little bending I think.
Of course grind off the company name :D
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D
Pages: 1 [2] 3 4 5 6 7 ... 13   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal