Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Soundboard Splits  (Read 2097 times)

0 Members and 1 Guest are viewing this topic.

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Soundboard Splits
« on: March 30, 2019, 03:10:44 PM »

I just started assessing a Hohner 1 row presswood and quickly learned of 2 splits in the sound board. I saw Theo's post about using wood veneer as a filler, but it seems to me that a lot of wood would have to be sanded out to make room for the veneer, in this situation.  Is that the way it needs to be, or are there other options for a quality repair? Thanks
Logged
Hohner Club IIB Victoria

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Soundboard Splits
« Reply #1 on: March 30, 2019, 03:28:44 PM »

Well that's a bummer. Assuming that the fondo is plywood, I'd be happy to use a wood filler, but others may disagree. Let's see what the experts think.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Soundboard Splits
« Reply #2 on: March 30, 2019, 03:38:57 PM »

I don't think it is plywood John, so it needs something with enough strength to resist further cracks.

You are going to have to remove the complete treble mechanism before you start.  Remove fingerboard, release all the springs then undo the screws holding the action. That bit is easy!

Most of those cracks look wide enough to fill with thin veneer. For thinner cracks you could use the sodium bicarbonate and superglue method.   You fill the gaps with bicarb then add thin superglue,   It sets almost immediately.   To do that you will need to tape over the cracks on one side so the bircarb doesn't just fall through.  That will mean taking out the reeds.

For a quick fix you could just apply a strip of adhesive tape over the length of the cracks, then re-cut the air vents.  You may still get air leaks between notes.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Soundboard Splits
« Reply #3 on: March 30, 2019, 04:15:21 PM »

I concur with Theo; bear in mind a wood veneer is VERY thin.  The splits look pretty straight, too - wood veneer is the way I'd go.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Kimric Smythe

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 712
    • Smythe's Accordion Center
Re: Soundboard Splits
« Reply #4 on: March 30, 2019, 04:28:45 PM »

For really thin cracks I have used pieces cut from a manilla folder, grocery bag paper, or pieces cut from a dollar bill depending on the crack width.
 The CA glue wicks in really well with these materials.
Logged
Smythe's Accordion Center
Pinole, California
Sales and repairs since 1997

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Soundboard Splits
« Reply #5 on: March 30, 2019, 04:29:07 PM »

Yep, if it's not ply, then veneer is the way to go. I'd still fill the cracks with OSMO wood filler, before I applied veneer, but  that's just a personal choice.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Soundboard Splits
« Reply #6 on: March 30, 2019, 04:46:49 PM »

Thanks for the feedback everyone. Apart from these splits, this box is in really nice shape. So...it looks like I'll do the repair with veneer before doing the "normal" repair work. This will be my first soundboard repair. It will be good to learn something new!  It sure was interesting the first time I pickup up this box...gave it a squeeze...and felt the wind blowing on my right hand!  Again, thanks to all. I appreciate the advise.
Logged
Hohner Club IIB Victoria

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Soundboard Splits
« Reply #7 on: March 30, 2019, 05:41:24 PM »

Splitting of soundboards is a fairly common problem on stringed instruments. Common repair methods include, for cracks too wide to clamp closed and glue, Vee out the crack and make a tightly fitting matching spline patch from the same species of wood. If the cracked can be closed, I temporarily glue small blocks of wood on either side of the crack with superglue. Several pairs may be needed. The blocks create a way to apply clamps across the crack to close it. After the glue applied in the crack is cured, the clamps and the temporary blocks are removed. This method works well for arched surfaces as well as flat. Traditionally, cracks in woodwinds were filled by melting hard shellac into the cracks. I have successfully used the spine method for gapping cracks and glue method for filling small cracks in accordion soundboards.
Logged
I'm squeezin' and they're wheezin': old junker boxes

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Soundboard Splits
« Reply #8 on: March 30, 2019, 05:51:25 PM »

Looks to me that the sound board is made of 3 the strips of edge jointed wood, if so they're not cracks but 'splits' where the joints have come apart due to shrinkage. You can see the line of the edge joint on the right hand side where the joints are still sound.

Presumably it's not possible to gently clamp them together with glue in the 'splits'.  A humidifier inside the box may possibly close the joints up, don't know if that would have any effect on the non wood parts.
Logged

boxcall

  • You got to love it!!!
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1801
Re: Soundboard Splits
« Reply #9 on: March 30, 2019, 10:35:56 PM »

For really thin cracks I have used pieces cut from a manilla folder, grocery bag paper, or pieces cut from a dollar bill depending on the crack width.
 The CA glue wicks in really well with these materials.

When I got a hohner presswood from my Papa, it had a piece of paper tape along a small but long crack, it was labeled O’Byrne Dewitt, so that’s what they did and it seemed to work for many years.
It was losing it grip so I did the super glue method, I had the reeds out so I could do both sides where possible. Most of mine was under the reed block wood also.
Logged
Hohner 1040 C, Beltuna one row four stop D, O'Byrne Dewitt/ Baldoni bros. D/C#, Paolo soprani "pepperpot" one row D

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re: Soundboard Splits
« Reply #10 on: March 31, 2019, 10:43:26 AM »

Looks to me that the sound board is made of 3 the strips of edge jointed wood,


I don't think the fondo is made from edge jointed timber, Ive never seen such construction used, (which is not to say it never happened),...   If you look carefully between some of the pallets at the split you can see evidence of grain tearing along the crack, Veneer or Superglue/Bicarb would seem the way to go
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Soundboard Splits
« Reply #11 on: March 31, 2019, 10:50:39 AM »

I have seen many one row (1040 and 114, 113, 112)  Hohners with solid timber fondo.  They were normal in the early examples of Hohner one row boxes. At a later period they switched over to ply.  The example here looks to me like solid timber, though it’s not possible to be sure just from a photo.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Henry Piper

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 368
Re: Soundboard Splits
« Reply #12 on: March 31, 2019, 11:55:54 AM »

Theo, if your last reply was in response to mine immediately before, I was not saying i'd never seen solid Fondo's, I have like you seen quite a few !!, My comment was in respect of Gromit's suggestion that the one in the box under discussion  was made of three pieces of Timber joined edge to edge !!, I have never seen this, Have you ??  I would have thought this would leave the whole fondo very prone to warping and general deformation
H
Logged
From Ottery St Mary Devon. Currently Playing Dino Baffetti BP2 in D/G, Hohner Student 1 P.A conversion  in D/G,  Hohner 3515 Pre-Pokerwork in A/D,   2 row "Beaver Brand" in Bb/Eb, Hohner Pre- Erica in G/C .  Single row permanent 4 voice, 4 bass in C from old Hohner single row and bits of a cheap Cajun box !!,

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Soundboard Splits
« Reply #13 on: March 31, 2019, 12:27:56 PM »

I can't recall if I've seen three edge jointed boards, but the timber does not have the usual appearance for the ply that Hohner used.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Soundboard Splits
« Reply #14 on: March 31, 2019, 12:31:00 PM »

Quote
I don't think the fondo is made from edge jointed timber, Ive never seen such construction used, (which is not to say it never happened),...   If you look carefully between some of the pallets at the split you can see evidence of grain tearing along the crack, Veneer or Superglue/Bicarb would seem the way to go

You can see that there are 3 separate strips which have been edge jointed - 1. The figure in the wood is different in each strip - 2. As I said before the glue line can be seen where it hasn't separated on the right of the pallets - 3. It's good practise in cabinet making to not use a solid piece of this width due to the danger of shrinkage and warping. The one small tear that's visible is not unusual when edge joints open up
Logged

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Soundboard Splits
« Reply #15 on: March 31, 2019, 01:28:54 PM »

I had an old Hohner 6 stop with two splits in the soundboard. The splits also were curling up on each side of the crack. I couldn't squeeze them shut so I glued them flat using CA glue then clamped with backing plates on the back side. After curing I filled the remaining now flat cracks with wood filler. This was an exposed soundboard design so I painted the filler with matching black paint. Here is a demo video with pictures of the repair both sides. The link starts at 1:20 when the pictures appear:
https://youtu.be/qn_7Wvr8L3I?t=80

Barry- I am running a repair, maintenance and tuning workshop in western NY June 6 & 7 and there are two spots left. I will be covering these kinds of repair during the course in case you are free and can drive over.

Scott

BellingersButtonBoxes.com
Logged
too many boxes...please buy one, or two, or

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Soundboard Splits
« Reply #16 on: March 31, 2019, 01:43:07 PM »

There are, surely, conflicting clues in the picture. At the extreme right, there are lines which continue to the end of the board, which look like joints. But as one proceeds across the pic, the tear between the two pallets does look as if it's the grain separating. However, yet further along, the crack has altered position altogether (twice, I think) before returning to its original line.
Very strange, I would have thought. The top line looks as if it could have been made with a pencil and straight edge, perfect!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Barry Tolson

  • Good talker
  • **
  • Offline Offline
  • Posts: 65
Re: Soundboard Splits
« Reply #17 on: March 31, 2019, 11:00:59 PM »

I've looked at this under bright light and magnification. It is solid timber, not ply..and the splits seem to be following the grain at a slight angle. I don't think it is edge glued.
« Last Edit: April 01, 2019, 10:00:50 PM by Barry Tolson »
Logged
Hohner Club IIB Victoria

Gromit

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 588
Re: Soundboard Splits
« Reply #18 on: April 02, 2019, 12:01:42 PM »

Although this video is about a guitar top repair there's some stuff here that could be used for repairing melodian splits, at approx. 2.20 the violin suction pad tip is useful..
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal