Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Keyboard rebuild.  (Read 2127 times)

0 Members and 1 Guest are viewing this topic.

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Keyboard rebuild.
« on: April 04, 2019, 01:30:30 AM »

Okay it's daft, but I am rebuilding a blown out keyboard for an old Hohner, thought you might enjoy the progress.
If anyone has a used plastic one, I've got a few more boxes that have followed me home, and one of those needs one! (yes I know they're available new.)

Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #1 on: April 04, 2019, 01:40:19 AM »

Here's there new top layer and the old box cut down, ready to laminate,  I used fine grained maple (or possibly very fine grained beech?) from some wood from an old German flat backed bass bit I had around. Very similar material and needed only a little thinning on the belt sander.
Making the oval holes wasn't too bad, laid them out and drilled therm just under 1/2" diameter, then made a little plastic template to draw in the amount of elongation required and finished them by hand with a cuts all burr and a larger round file. I made a sort of double fence set up for the table saw to reduce the thickness of the old keyboard, and smoothed it with a hand plane.

« Last Edit: April 04, 2019, 02:41:40 AM by Mark Leue »
Logged

Pat McInnis

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 390
Re: Keyboard rebuild.
« Reply #2 on: April 04, 2019, 03:12:35 AM »

That's some really nice work!! I did a cut and paste repair with two busted early Hohner boards and it also worked out pretty good. I regretted not sanding it more before painting but I wasn't even sure if it would survive going over the buttons. It did and it just looks tough but not broken. Yours looks super slick.
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Keyboard rebuild.
« Reply #3 on: April 04, 2019, 07:30:26 AM »

Nicely done!
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Keyboard rebuild.
« Reply #4 on: April 04, 2019, 07:55:27 AM »

V good indeed. So...you removed the top of the old keyboard with your table saw? Can you say a bit more about the 'double fence' please?

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Keyboard rebuild.
« Reply #5 on: April 04, 2019, 09:05:21 AM »

very nice..I have at least 3-4 wooden keyboards needs that top layer job, why not make some extra for people like me with no tool or wood work skill?  8) 
Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #6 on: April 04, 2019, 11:03:29 AM »

As I was making the replacement top, I was thinking to myself I should be making this once out of polycarbonate instead.  That way I  can do this much faster with a pattern following router bit if I ever needed to do it again.  In fact with my milling machine and a jig or two I could just make a whole keyboard from scratch.
There is perhaps a strange variant of MAD out there, Melodeon Upgrading Disease.
Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #7 on: April 04, 2019, 11:16:35 AM »

V good indeed. So...you removed the top of the old keyboard with your table saw? Can you say a bit more about the 'double fence' please?

I think next time Id do it the SANE way with the bandsaw angling the table to match the angle of the bottom of the keyboard, and using the bandsaw fence.  I cant actually believe I did it on the table saw the way I did, although it did work well. You need to be removing exactly the blade kerf for it to work and the second fence is creating a tunnel for the keyboard to pass through... eh.  don't do it that way.
OR better yet, a router jig...
« Last Edit: April 04, 2019, 11:22:25 AM by Mark Leue »
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Keyboard rebuild.
« Reply #8 on: April 04, 2019, 10:32:35 PM »

'Router jig'...oh I think I understand...machine the top layer off?

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #9 on: April 04, 2019, 11:14:34 PM »

It's best to assemble the new top and make sure everything works before gluing, In fact I did my glue up with the whole keyboard assembly attached to the box, spread the glue, got a couple of clamps on, and went to remove it so I could finish clamping etc.
Surprise! you can easily assemble it in such a way that it works fine but you cant slide the assembly off the buttons anymore!
So after a couple of minutes of improvising I manage to get a piece of wire under the pallet levers and with a little help from my shop assistant who was luckily nearby managed to raise the pallets enough to slide it off and save the assembly process I had started.
Then after the glue dried I spent quite a while carving out enough wood so I could easily assemble and disassemble the keyboard as a unit. The issue was that although the total thickness of the thing was perfect, I made my keyboard surface piece a little thicker, and removed a bit more off the old bottom bit, leaving less hollow space inside.
After it dried I tweaked a couple of button holes that were out of line, and went to work on restricting the action.
What I came upon with after some trial and error was a shim covered with dense neoprene (high durometer sheet stock)  that was slightly wedge shaped to make the two rows have the same amount of travel. I decided to leave the playing surface natural and blackened the rest with a little black pigmented shellac. There is an amazingly deep indentation from the thumb wear of previous squeezers 
« Last Edit: April 04, 2019, 11:52:38 PM by Mark Leue »
Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #10 on: April 04, 2019, 11:15:37 PM »

Here's the wood and neoprene sandwich in place
Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #11 on: April 04, 2019, 11:17:40 PM »

And a shot of its shape from the end... the thicker side faces towards the keyboard as the longer inner row pallet arms have more travel until they bump the thicker bit of rail.
img][/img]
Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #12 on: April 04, 2019, 11:19:24 PM »

'Router jig'...oh I think I understand...machine the top layer off?

Yes that is the most sensible way to accomplish that.
Logged

Psuggmog Volbenz

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 318
    • musical whimsy
Re: Keyboard rebuild.
« Reply #13 on: April 05, 2019, 06:42:37 AM »

A well thought out and executed repair. I have resorted to a more tedious method of replacing the missing bits from a damaged keyboard similar to the one in your initial photho. I did so to retain the original decorative embossing on the keyboard, which is not present on your model. I believe that part of the reason for the common failure of these keyboards is excess flexing of the perforated board over time. On my repairs, I add several wooden compression posts to stiffen the keyboard. I also limit the keytravel as you did. Thanks for sharing. I noticed that the metal key levers have quite a bit of surface oxidation, are the reeds rusty as well?
« Last Edit: April 05, 2019, 06:44:54 AM by Psuggmog Volbenz »
Logged
I'm squeezin' and they're wheezin': old junker boxes

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Keyboard rebuild.
« Reply #14 on: April 05, 2019, 11:46:57 AM »

would it not be better to fix the new top with a few screws like old club models so you only remove the top when & as you need to rather than permanent fix? button limiting will be came easier and can be modified with a felt under the buttons... where do I send my damaged wooden key board for for new top  Mark  :D ?       
 
Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #15 on: April 05, 2019, 12:16:36 PM »

. I noticed that the metal key levers have quite a bit of surface oxidation, are the reeds rusty as well?
[/quote]

The reeds are a little puzzle. As near as I can tell they've all been replaced except for four treble reeds that are original zinc mounts.
either that or it was made with mixed reeds to start with. either way I think they're okay. Im wanting to change the key from CF to AD if I can, as I need a challenge and and AD box as well.  My MUD syndrome is bad...


 So is this amount of oxidation and small rust spots a problem? I'm a novice, so I know NOTHING about accordion reeds I haven't picked up on the internet. And so far, I haven't learned much there either.That's part of why I'm hanging around here, hoping to learn more.

And in reply to inquires about fixing other's keyboards. Not at this time, but if I ever gear up to make the tops with a router and make a proper jig to reduce thickness I'll let you know.
« Last Edit: April 05, 2019, 12:21:44 PM by Mark Leue »
Logged

Mark Leue

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 175
Re: Keyboard rebuild.
« Reply #16 on: April 05, 2019, 12:23:18 PM »

would it not be better to fix the new top with a few screws like old club models so you only remove the top when & as you need to rather than permanent fix?

Much better!  that's version 3.5
Logged
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal