Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Advice on finishing new veneer  (Read 1878 times)

0 Members and 1 Guest are viewing this topic.

ju

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 174
Advice on finishing new veneer
« on: April 17, 2019, 05:09:57 PM »

Just in the process of veneering a box and wondering what finish  I will apply ? Any experts out there with an informed opinion ?? Do I french polish ( for the first time ?) or go for varnish ?  Or any other options . The wood veneer is Zebrano , I will be filling the pores once all glued down and sanding back .
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Advice on finishing new veneer
« Reply #1 on: April 18, 2019, 04:41:21 AM »

French polish is v nice but I’d worry about its robustness on something that’s going to get handled quite a lot. The Pariselle boxes are varnished with a tough substance similar to what is used on guitars etc. However on balance I’d probably french polish if the instrument is for me. You can repair french polish, which is one of its virtues. And on some old Hohner the bass board (the bit under your hand) is french polished.

ju

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 174
Re: Advice on finishing new veneer
« Reply #2 on: April 18, 2019, 06:32:43 AM »

Does anyone have any experience of The Liberon “ Easy French polish “ ? thought if it was any good it might be easier for french polishing amateur .
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Advice on finishing new veneer
« Reply #3 on: April 18, 2019, 07:39:03 AM »

Does anyone have any experience of The Liberon “ Easy French polish “ ? thought if it was any good it might be easier for french polishing amateur .
Yes - I've used it. It works fine but it takes a bit of getting used to the technique of applying it. You need to spend a bit of time practicing on some spare bits of wood.
The key points for me are
(i) Ensure your wood surface is sanded down really well to a fine satin-like surface; finishing with 400 and then 600 grade sandpaper/carborundum paper is worth doing.
(ii) Follow the instructions about making a 'rubber' and apply the polish sparingly with light strokes and keeping the rubber moving all the time. When first contacting the wood with the rubber, imagine it's an aircraft landing, and similarly when finishing the contact, think of an aircraft taking off.
(iii) Don't apply too much polish at once. Build up the shine with successive layers.
(iv) Rags saturated with french polish can dry out and spontaneously combust :o, so wash them in hot water and detergent thoroughly after use and allow to dry.

Good luck!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Advice on finishing new veneer
« Reply #4 on: April 18, 2019, 08:04:55 AM »

I learned the basics of french polishing by watching this fellow..the videos are quite soothing too..
https://youtu.be/nOLdP752fMM
I keep my rubber in a screw-top jar.
A tip I got from Will the furniture restorer on The Repair Shop was to use 0000 wire wool after you applied your polish (and it had hardened overnight) then paint restorer (it’s like very fine T cut) to get a mirror image. I’d test this technique first however. But the great thing about french polish is it’s reversible and if you mess it up you can fix the problem.
Here is a picture I took to remind me of Will's advice.
https://photos.app.goo.gl/4HnTWBNA2Y51ngB57

ju

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 174
Re: Advice on finishing new veneer
« Reply #5 on: April 18, 2019, 08:12:29 AM »

Thanks for the tips  . Some more glueing to do yet , but will let you know how it turns out , will be a while though  .
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Advice on finishing new veneer
« Reply #6 on: April 18, 2019, 08:17:12 AM »

A couple of pictures would be great, ju, if you remember.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Advice on finishing new veneer
« Reply #7 on: April 18, 2019, 08:49:26 AM »

Just a thought, but if I were using a nice wood like zebrano I’d be looking for a clear finish. I think even the lightest French polish would take the colour down.
I’ve used black French polish, I think it was Liberon. Quite satisfying, especially as you have to work for it!
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Advice on finishing new veneer
« Reply #8 on: April 18, 2019, 12:30:35 PM »

not on a veneer but I have used tru oil on bare wood and wood dye, both came out beautifully..tru oil was suggested to me by a member and he was spot on  (:)
french polish is very hard to get it right for a beginner, I had a go at it a few times but never had the same finish as the videos from YouTube :o
tru oil is very easy to apply by your finger and a drop goes along way, a few coats give you a very nice and shiny ember colour finish and you can buff it to your preferred finish..and it gets better as it gets older..£10 a bottle will give you 3-4 finished boxes if not more,cheap to buy.easy to apply,no tool needed,apply as many coats as you like,buff it with fine steel wool when you happy with the look.
have a go you'll like it
           
Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Advice on finishing new veneer
« Reply #9 on: April 18, 2019, 12:44:21 PM »

I use Danish oil which is based on Tung oil. Again, best applied sparingly. I have been known to warm it first, before applying it, using my fingers.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Advice on finishing new veneer
« Reply #10 on: April 18, 2019, 03:22:41 PM »

It was Spanish/British guitarmaker Jose Romanillos who said about French Polish something like: you keep at it and eventually it will start working for you.  So expectations should be realistic for a first time.

+1 for Tru-Oil.  I tried it on my one-row project box and found it fairly easy to use.  It gives a nice shine in a thin coat (similar in that to French P) as opposed to the wood-wrapped-in-plastic look of some varnish or lacquer finishes.  Tru-Oil was designed for gunstock finish but information is available online for using it on musical instruments (on MandolinCafe among other places).   
Logged

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Advice on finishing new veneer
« Reply #11 on: April 18, 2019, 04:02:55 PM »

Liberon was mentioned: they also have a wide array of varnishes in different shades and colours. I regularly use them in my own boxes.
Logged

ju

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 174
Re: Advice on finishing new veneer
« Reply #12 on: April 18, 2019, 04:05:34 PM »

So many choices 🤔 . Maybe Liberons “EASY FRENCH POLISH “ is a bit of a misnomer . Would hate to mess it up at the finishing stage .
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Advice on finishing new veneer
« Reply #13 on: April 18, 2019, 04:09:30 PM »

Emmanuel uses Rustins Plastic Coating on the courses.  It is a two part coating, very easy to apply and supremely durable.  It doesn't look plasticky and can be burnished to a gloss or by using fine Scotchbrite or 00 steel wool for a nice satin finish.  Wax polish too if you want.

So many choices 🤔 . Maybe Liberons “EASY FRENCH POLISH “ is a bit of a misnomer . Would hate to mess it up at the finishing stage .

If you decide on French polish then spend some time practicing on spare wood first.  Large flat surfaces are less difficult than complicated shapes like melodeons.
« Last Edit: April 18, 2019, 04:11:20 PM by Theo »
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Advice on finishing new veneer
« Reply #14 on: April 18, 2019, 04:10:13 PM »

Liberon waxes are good, I use them to finish stuff I have turned on my lathe. I have a hankering to try their Pure Beeswax with Paraffin, as I reckon that would give a great finish. All their stuff I have tried so far, is good.

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Advice on finishing new veneer
« Reply #15 on: April 18, 2019, 06:11:39 PM »

Oooh..Tru oil..I need to give that a go... I think that’s what my restored English mandolin is finished with..and it’s great.
« Last Edit: April 18, 2019, 06:16:10 PM by RogerT »
Logged

invadm

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 613
Re: Advice on finishing new veneer
« Reply #16 on: April 18, 2019, 07:26:00 PM »

here it is, on single row and wood dye club, I think I only did 3 coats in total.
« Last Edit: April 18, 2019, 07:29:05 PM by invadm »
Logged

IanD

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1703
  • Too many melodeons...
Re: Advice on finishing new veneer
« Reply #17 on: April 19, 2019, 12:16:37 PM »

You could also look at Junckers Rustic Oil, gives an oiled wood look but is impervious to dirt and water, and is easy to refinish. Normally used on high-class hand-made furniture but I expect it will work just as well on a melodeon :-)
Logged
Oakwood Model 4 D/G, Castagnari Dony D/G/#, Castagnari Tommy G/C, Baffetti Binci D/G, Hohner Preciosa D/G, Melos Bb/Eb, Lightwave SL5 and Kala California fretless basses
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal