Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Tuning Table-Sensible size  (Read 1206 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Tuning Table-Sensible size
« on: June 18, 2019, 10:26:32 PM »

Any suggestions as to a sensible size for the working surface of a tuning table?  Intending to use Lester's approach of using a spare reed block as "carrier" for individual reeds. Also intend using it to tune long plate reeds.

Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Tuning Table-Sensible size
« Reply #1 on: June 19, 2019, 08:49:34 AM »

If you plan to tune PA reed blocks, the big ones - sometimes 22 plates long - consider how far each side of the central table  holes it is going to protrude, when you are tuning an end reed.  If you have seen Lester's tuning rig I think it might be a bit narrow for PA blocks. But Lester might disagree...

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning Table-Sensible size
« Reply #2 on: June 19, 2019, 12:32:13 PM »

My suggestion for size (in the example which RogerT gives) would be to have the surface of your table long enough so that when the end reed is over the blow hole, you can let go of the block without it falling off! This could mean (depending what actual space you have) that your blow hole has to be off-centre.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Tuning Table-Sensible size
« Reply #3 on: June 19, 2019, 12:37:07 PM »

Mine is 330mm wide, this was driven by the bellows I had. The hole is in the middle so full support 160mm either side. A pokerwork reed block is 230mm so it overlaps the edge when tuning and a piano accordion block would overlap more but this has never ever caused a problem.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Tuning Table-Sensible size
« Reply #4 on: June 19, 2019, 06:16:52 PM »

Thanks Guys - I think that's enough information to let me make something functional. Photos to follow - that's a challenge to myself to actually make it!
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Tuning Table-Sensible size
« Reply #5 on: June 30, 2019, 12:37:13 AM »

Sometime later.....

Box is 50mm deep, 350 mm front to back and 400mm wide.

P.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning Table-Sensible size
« Reply #6 on: June 30, 2019, 06:46:07 AM »

Very nice, but I could imagine it becoming quite wearing on the arm and shoulder with constantly lifting the bellows against the restriction of dragging air through the small blow-hole. Time will tell.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Tuning Table-Sensible size
« Reply #7 on: June 30, 2019, 07:50:00 AM »

Lester has an air button to allow faster refill. I’m sure he will enlighten you.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal