Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Accidental button reversal  (Read 1098 times)

0 Members and 1 Guest are viewing this topic.

Doug

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 105
Accidental button reversal
« on: June 29, 2019, 07:05:50 PM »

I want to reverse the push and pull on one of the chin end accidentals. Is it just a case of taking the pairs of reeds out and turning them over? Or is there a lot more to it?

Doug
Logged
Serenellini 3v, Dino Baffetti Oakwood Super 2v  and Castignari Giordy. All D/G.

Fred

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 719
  • G/C Pariselle, D/G Loffet & maybe too many Hohners
Re: Accidental button reversal
« Reply #1 on: June 29, 2019, 07:12:37 PM »

I want to reverse the push and pull on one of the chin end accidentals. Is it just a case of taking the pairs of reeds out and turning them over? Or is there a lot more to it?

Doug

It's just that.
Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Accidental button reversal
« Reply #2 on: June 29, 2019, 07:17:09 PM »

I want to reverse the push and pull on one of the chin end accidentals. Is it just a case of taking the pairs of reeds out and turning them over? Or is there a lot more to it?

Doug

It's just that.


Well you really need some method to reflow the wax, I use a soldering iron but a knife blade heated with a ciggy lighter would do.

Doug

  • Regular debater
  • ***
  • Offline Offline
  • Posts: 105
Re: Accidental button reversal
« Reply #3 on: June 29, 2019, 07:32:56 PM »

Thanks for the advice chaps. I can visualize your soldering iron, Lester.
Doug
Logged
Serenellini 3v, Dino Baffetti Oakwood Super 2v  and Castignari Giordy. All D/G.

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Accidental button reversal
« Reply #4 on: June 29, 2019, 07:39:45 PM »


Thanks for the advice chaps. I can visualize your soldering iron, Lester.
Doug



If you would like to check your visualisation
https://youtu.be/frzbE8P0t_o

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Accidental button reversal
« Reply #5 on: June 30, 2019, 08:40:03 AM »

Precautions when flipping reed plates

1. Valve length
You need to check that the valve which was on the outside does not foul the walls or end of the reed chamber when flipped to become the underneath valve. Often there is only a tiny gap between the chamber walls or end, so the valve length and its lateral placement are critical. If the valve does foul at all, the result will be a poor or buzzy sound and often a sudden change in volume and pitch with increasing air pressure as the caught valve suddenly frees itself halfway through a note. When the outside valves are originally installed, the length and lateral placement is not quite so critical, so sometimes these valves are slightly longer than strictly necessary, which may lead to fouling problems when flipped over.

You need to check the valve clearance as you re-position the flipped reed plate. Usually you can do this by eye as you offer the flipped plate into its new position just prior to re-waxing. A good test is to look through the air vent so you can see the underneath valve and at the same time depress the reed tongue into the slot with a cocktail stick. You should be able to see if the valve moves freely as the reed tongue descends on to it.

If the valve is fouling because it is too long, reduce the length by trimming a tiny sliver off the end with a sharp blade, while being careful not to expose the end of the reed plate slot nor damage the reed plate itself (use a small piece of card to act as a shield when cutting). If the valve is fouling the side wall of the reed chamber, ease the reed plate sideways a fraction until the valve is clear. You may even need to replace the valve with a new one, setting it just a fraction nearer the centre of the reed plate.

2. Tuning
Once you've done the reed plate reversal, you may find that the tuning is slightly out because of the different acoustic environment of reed tongues previously on the inside of the reed chamber now being on the outside. They will tend to be a fraction sharper than previously.

Most of the time this won't matter too much as the change in pitch is generally within what is acceptable as 'in tune' for most people. However, it might make an audible difference to the tremolo rate if the instrument is tuned with only a light, slow tremolo to begin with. There's no real way of predicting this in advance; you'll just have to wait and see what the result of flipping the reed plates is. If your instrument is tuned to a reasonably wet Hohner-ish tremolo, you will probably not notice anything untoward.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Accidental button reversal
« Reply #6 on: June 30, 2019, 05:22:03 PM »

Steve is covering every possible problem.  In practice it’s a simple process of flipping the reed plates, and rewaxing.  Tuning is likely to be acceptable, if not absolutely perfect without any further work.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Accidental button reversal
« Reply #7 on: June 30, 2019, 07:59:49 PM »

Steve is covering every possible problem. 
You know me - I like to be thorough!
 ;)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal