Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1] 2 3   Go Down

Author Topic: Tuning Methodology- In the box or outside the box  (Read 6863 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Tuning Methodology- In the box or outside the box
« on: August 11, 2019, 08:47:23 AM »

I have just started trying to improve the tuning on my Hohner 1040/G.  This is my first attempt to seriously tune a melodeon and with some reed pairs are out at 20+ cents. (I should maybe work out the standard deviation!)

Detailed discussion in previous threads makes it clear that for very precise tuning reeds have to be tuned in situ.

There are however 3 places in which reeds can be tuned.

1. Tune As individual reeds on tuning table (easiest for scraping but frequency response of reed will change firstly when it is set in the reed block and secondly when the reed block is

2. Tune Set in the reed block ( more difficult but the inside reeds can be accessed through the ports in the soleplate of the reed block - minor frequeny shifts expected expected when block is put back in the instrument)

3. In situ (minimal frequency shift when bellows re-attached - but most difficult and with risks of pulling reed plates off the block and or creasing plastic valves in the process)

As a preliminary to tuning I went go through all the individual reeds tabulating their existing frequencies and found some quite irregular steps (+/- 20cent) both in absolute tuning and in the  offset between the M and M+ reed banks.

Step 2 isn't available in most 2 voice 1 rows  (Including Hohner 1040 & HA112), because the reed chest in these is a simple ladder arrangement glued to the fondo (The only exception I know of is the Chanson 7 key and it's variants).

So the question of the day is how much scatter in tuning is likely to result if I just take the reeds out and get them individually in good tune outside the box.

Anyone got any figures?



Logged

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama
Re: Tuning Methodology- In the box or outside the box
« Reply #1 on: August 11, 2019, 08:58:38 AM »

My method for 1040s etc is to tune the reeds outside the box on a scrap pokerwork reed block* I aim for +2/3 cents from the desired pitch. Then I wax them in place and fine tune by lowering the pitch whilst sounding them in the box.

*I use a pokerwork reed block as the cavity sizes are near enough to the 1040/114 cavities to remove that difference from the confusion.

For in box tuning I have a piece of plywood from which I suspend the bellows and the bass end so I can pop the treble end on sound the reed, pop it back off etc etc

Picture to replace a thousand words

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Methodology- In the box or outside the box
« Reply #2 on: August 11, 2019, 09:06:55 AM »

If you want to stay with the typical Hohner wet tuning then you can get away with tuning the reed plates outside the box,  because the errors that will result will be concealed by the strong tremolo.  It would still sound better with the reeds tuned inside the box, but many people would not be able to tell the difference.

On the other hand for tunings with minimum degrees of tremolo as found on many Italian boxes the only way to get it right is to tune with the reeds on the blocks, and the blocked fitted in the instrument.  I tune all instruments this way,  even those with flat mounted reeds like the 1040. 

Once you have built up some skill and have the right tools it’s also quicker than the fitting and the-fitting of reed blocks that you have to do with other methods.

I’d better take some photos and write up my method.

BTW the Hohner 112 (2 stop) does not have flat mounted reeds.  It has a single upright reed block on all the examples I’ve seen.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Tuning Methodology- In the box or outside the box
« Reply #3 on: August 11, 2019, 01:32:12 PM »

[quote author=Theo link=topic=24319.msg289813#msg289813 date=1565510815

BTW the Hohner 112 (2 stop) does not have flat mounted reeds.  It has a single upright reed block on all the examples I’ve seen.
[/quote]

Apologies- have opened up my 112 and Theo is absolutely right as usual. Wondering how I convinced myself that it was the same as the 1040  :|bl.
Peadar
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Tuning Methodology- In the box or outside the box
« Reply #4 on: August 11, 2019, 04:14:18 PM »


For in box tuning I have a piece of plywood from which I suspend the bellows and the bass end so I can pop the treble end on sound the reed, pop it back off etc etc




I got lucky when I built my tuning table. Completely by accident I made the table in front of the bellows just larger than a pokerw ork's casework. So far the surface fit between the table top and he rim of the 1040 treble end is good enough that I can sound the reeds just by putting the treble end down on the tuning table. This won't work once I try to tune something with an upstanding reed block but hey! one step at a time.

Tuning outside the box will do to start with.
Logged

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Tuning Methodology- In the box or outside the box
« Reply #5 on: August 12, 2019, 08:06:10 AM »

It v easy to knock up tuning bellows (if you happen to have some old accordion bellows and a couple of bits of plywood). In this photo you can see the bellows I made for tuning one-row instruments. The treble (or bass) case sits on the big hole and the bellows are clamped to the bench.
https://photos.app.goo.gl/mZ81onYdLAaJeZkC8

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Methodology- In the box or outside the box
« Reply #6 on: August 12, 2019, 09:17:54 AM »

It v easy to knock up tuning bellows (if you happen to have some old accordion bellows and a couple of bits of plywood). In this photo you can see the bellows I made for tuning one-row instruments. The treble (or bass) case sits on the big hole and the bellows are clamped to the bench.
https://photos.app.goo.gl/mZ81onYdLAaJeZkC8

My set-up is very similar to Roger's and works very well, especially for tuning with the reed blocks in-situ.
The dimensions of my large opening are such that most melodeons fit over the width just right. The length of the opening is generally slightly longer than most melodeons, so I have a separate piece of thin ply covered with chamois leather, which I can butt up to the end of the melodeon to close up the gap. See photos.

I find this set-up gives me very consistent results. For very accurate tuning, e.g. Castagnari with very light, slow tremolo, I still prefer to tune by off-sets rather than accept what the tuning meter tells me the pitch is when the instrument is sounded on the tuning bellows. The discrepency tends to be no more than about 1 - 2 cents from when sounded in the assembled instrument. I measure the tuning of each reed in the assembled instrument to establish the baseline, then measure the pitch on the tuning bellows and adjust the reed by the required amount. Works nicely.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Methodology- In the box or outside the box
« Reply #7 on: August 12, 2019, 09:19:20 AM »

More photos...
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning Methodology- In the box or outside the box
« Reply #8 on: August 12, 2019, 10:12:39 AM »

I must admit to being a bit mystified as to why you two professionals choose to use a separate bellows system for tuning "inside the box". I expect that there'll be some perfectly sound reason for this, which didn't even approach my conscientiousness, but it seems to me to be yet another time taking process, which could be missed out.
As Steve says, "I measure the tuning of each reed in the assembled instrument to establish the baseline, then measure the pitch on the tuning bellows and adjust the reed by the required amount."  Isn't that an extra job which could be by-passed?
Although I've yet to have a go at tuning reeds in a fixed-in block, I copied one of my tuning bellows arrangements (from somewhere or other) which uses the instruments own bellows straight away. I really don't have room for extra sets of bellows sitting around and getting in the way when not in use, either!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Methodology- In the box or outside the box
« Reply #9 on: August 12, 2019, 10:30:30 AM »

I must admit to being a bit mystified as to why you two professionals choose to use a separate bellows system for tuning "inside the box".

Me too.  I use the same system as you do Winston.  It's simple, quick, the reeds are in the exact environment where they will be played, there is no need for "offset tuning".  The equipment is simple, and cheap and easy to make an additional plywood bellows holder when you come across an unusual size of instrument.   I have half a dozen of different sizes that covers all the boxes in common use.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Methodology- In the box or outside the box
« Reply #10 on: August 12, 2019, 10:58:40 AM »

I must admit to being a bit mystified as to why you two professionals choose to use a separate bellows system for tuning "inside the box". I expect that there'll be some perfectly sound reason for this, which didn't even approach my conscientiousness, but it seems to me to be yet another time taking process, which could be missed out.
As Steve says, "I measure the tuning of each reed in the assembled instrument to establish the baseline, then measure the pitch on the tuning bellows and adjust the reed by the required amount."  Isn't that an extra job which could be by-passed?

I'm sure this has been explained before, by me and others.

The pitch of a reed on a tuning table, tuning bellows, etc. is always going to be different from the pitch in situ in the instrument, fully assembled with all bellows pins or screws in place. Depending on the design, dimensions and rigidity of the tuning bellows and the set-up you are using, that difference can be 5 cents or more astray. So you have to allow for that by comparing the tuning bellows pitch with the in situ instrument pitch. If you don't then the results of any tuning alteration which you carry out will be inaccurate.

Here's an example of my methodology. I will have previously measured the pitch of every reed in the fully assembled instrument. Just taking the example of just one reed, say the A4 'at pitch' reed, but it could be any of them:

1. Pitch difference from Equal Temperament as measured in fully assembled instrument: -4.5 cents (it's flat!)
2. Amount of correction needed: +4.5 cents
3. Pitch difference from ET measured with reed blocks in situ but instrument opened up on tuning bellows: -2.0 cents (the pitch is not quite as flat on the tuning bellows, but we still need to sharpen it by 4.5 cents - see step 2).
4. Sharpen the reed to +2.5 cents (-2.0 + 4.5 = +2.5)
5. Reassemble the instrument. The reed should now (hopefully!) be sounding at zero cents difference from ET.

In my experience the differences between the in situ assembled instrument and the tuning bellows value can vary something like this:
Unmounted reed plate in a holder: perhaps +10 cents or more.
Reed mounted on reed block sounded on top of the tuning bellows table: approx. +5 cents
Reed mounted on reed block in situ in instrument but sounded on a tuning bellows: 0 to +2 cents.

These values are based on my set-up. Other set-ups will probably give different off-set errors, but there will almost certainly be some difference.

Edited to correct arithmetic typo caused by trying to combine putting out wheelie bin for collection at the same time as posting on melnet. Multi-tasking clearly not my strong point.
« Last Edit: August 12, 2019, 11:15:49 AM by Steve_freereeder »
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Lester

  • MADman
  • Mods and volunteers
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 9327
  • Hohners'R'me
    • Lester's Melodeon Emporium and Tune-a-Rama

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Methodology- In the box or outside the box
« Reply #12 on: August 12, 2019, 11:12:08 AM »

Replying to Theo's point:
I agree that using the instrument's own bellows will replicate the environment in which it will be played very closely but even then, there will be differences once the instrument is fully assembled and rigid. Not much, but measurable (typically in the order of 1 to 2 cents)

The bench top set-up I use is convenient for the very limited work room space I have.

I will always measure the 'as received' pitches for every reed as the first step so I know just how out of tune an instrument is. Any discrepency from the as received pitch, once on the tuning bellows will show up straight away and can be allowed for if needed. It's no hardship to do a quick bit of mental arithmetic to work out any tuning bellows corrections 'on the fly'. I also write everything down so I can track down and recover any errors or quirks - such as a pitch of a reed being influenced/interfered by the resonant frequency of the set-up.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Methodology- In the box or outside the box
« Reply #13 on: August 12, 2019, 11:13:31 AM »

-2.0 + 4.5 = +2.0

??
Oh bugger! Well spotted Lester. Of course it should be -2.0 + 4.5 = +2.5   :|bl
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Tuning Methodology- In the box or outside the box
« Reply #14 on: August 12, 2019, 11:14:37 AM »



The pitch of a reed on a tuning table, tuning bellows, etc. is always going to be different from the pitch in situ in the instrument, fully assembled with all bellows pins or screws in place.

And if follows that if you do all the tuning in the fully assembled instrument there is no offset.

I tune in the fully assembled instrument with all screws in place.  Bellows pins are out, but I’ve been unable to detect a difference in pitch based on the presence or absence of bellows pins.  I do cover the bellows pin holes with tape to avoid air escaping.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Tuning Methodology- In the box or outside the box
« Reply #15 on: August 12, 2019, 11:25:35 AM »

Quote
I must admit to being a bit mystified as to why you two professionals choose to use a separate bellows system for tuning "inside the box". I expect that there'll be some perfectly sound reason for this, which didn't even approach my conscientiousness,
If I understand your puzzlement correctly (and forgive me if I have missed your point)...  I have plenty of old bellows and making another tuning bellows takes 10-15 mins, and saves a lot more than that during tuning. I'm not trying to make a piece of furniture, I just knock them up with a jigsaw, drill, glue, gaffer tape and bits of craft foam. When I can I just lift the end on and off the instrument itself, but sometimes (as with a 114) it won't sit on the bench on either the bass or the treble side.
« Last Edit: August 12, 2019, 11:27:18 AM by RogerT »
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Methodology- In the box or outside the box
« Reply #16 on: August 12, 2019, 11:25:54 AM »



The pitch of a reed on a tuning table, tuning bellows, etc. is always going to be different from the pitch in situ in the instrument, fully assembled with all bellows pins or screws in place.

And if follows that if you do all the tuning in the fully assembled instrument there is no offset.

I tune in the fully assembled instrument with all screws in place.  Bellows pins are out, but I’ve been unable to detect a difference in pitch based on the presence or absence of bellows pins.  I do cover the bellows pin holes with tape to avoid air escaping.
Yes - I cover the bellows pin holes too.
I've had a couple of frustrating experiences with tuning discrepencies which I eventually tracked down to the presence or absence of bellows pins affecting the rigidity and hence the pitch of the reeds in the instrument. I think it depends on the instrument; it doesn't always happen but sometimes it does.

More recently, working with concertinas, the pitch is definitely affected by whether or not all the end bolts are in place.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning Methodology- In the box or outside the box
« Reply #17 on: August 12, 2019, 11:33:53 AM »

"I'm sure this has been explained before, by me and others."

Yes, but in your explanation here, only the difference which could be made by the bellows pins/screws not being present when tuning (and using the rest of the instrument as the bellows) is cited as being a possible variant. Surely such a difference would be infinitesimal?

I'm not being deliberately obtuse here, or trying to antagonise anyone, but I still cannot see any benefit in using a separate, specially constructed, bellows for this method of tuning, sorry!

"The bench top set-up I use is convenient for the very limited work room space I have."

Steve, as some of your fellows were once quoted as saying....."You were lucky!" You should see my cramped conditions. They're a major consideration in only using the instruments original bellows, as my storage space for another "special" set is already overwhelmed!

"but sometimes (as with a 114) it won't sit on the bench on either the bass or the treble side."

??? It just sits there in the "U" shaped hanging device, no need to balance or anything.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Tuning Methodology- In the box or outside the box
« Reply #18 on: August 12, 2019, 01:18:18 PM »

"I'm sure this has been explained before, by me and others."

Yes, but in your explanation here, only the difference which could be made by the bellows pins/screws not being present when tuning (and using the rest of the instrument as the bellows) is cited as being a possible variant. Surely such a difference would be infinitesimal?

I'm not being deliberately obtuse here, or trying to antagonise anyone, but I still cannot see any benefit in using a separate, specially constructed, bellows for this method of tuning, sorry!
See my earlier reply to Theo.
I do use the suspension by bellows set-up sometimes, but for me my work top mounted bellows works for me and is very convenient. It's especially easy to seat the instrument end very firmly on the bellows top.

The other advantage of the work-top mounted bellows is that I can clamp an additional sheet of plywood on top which has a single vent in it. I use this to sound individual reeds mounted on the reed block outside the instrument. This is good for checking the reed response and adjusting the reed tip gap as needed. Also good for checking whether the valves are working properly, especially after fitting replacements. These adjustments would be harder more fiddly to do on the suspension by bellows method.

Ultimately we all have our favourite tools and methods; these are mine.
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Tuning Methodology- In the box or outside the box
« Reply #19 on: August 12, 2019, 01:27:10 PM »

"I can clamp an additional sheet of plywood on top which has a single vent in it. I use this to sound individual reeds mounted on the reed block outside the instrument. This is good for checking the reed response and adjusting the reed tip gap as needed. Also good for checking whether the valves are working properly, especially after fitting replacements. These adjustments would be harder more fiddly to do on the suspension by bellows method."

A single vent is a must for me, too, on occasion. And your method would eliminate the need for a second set of separate bellows, thus saving space again! I also have a separate device for this, as pictured.

"Ultimately we all have our favourite tools and methods"

Very true, personal preference can be the spice of life in many circumstances.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!
Pages: [1] 2 3   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal