Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: 1 [2]   Go Down

Author Topic: Cardboard for bellows  (Read 3877 times)

0 Members and 1 Guest are viewing this topic.

malcolmbebb

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2628
  • In dampest Dorset, on the soggy south coast.
Re: Cardboard for bellows
« Reply #20 on: September 26, 2019, 09:02:41 AM »

Not in a position to check at the moment, but what would be the fold depth of say a Liliput or other small box? Charlie’s minimum is 2.7mm.
It’s not cheap, and I imagine could be quite wasteful to just tinker with or to make custom bellows for a small box.
On the other hand I have had a go at bending card and it’s not easy to get a presentable and consistent finish. My conclusion was that if I wanted a custom bellows for a small box, and wanted to make it myself, I would consider concertina style construction.
Logged
Dino BPII.
"Tradition is not the worship of ashes, but the preservation of fire."

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Cardboard for bellows
« Reply #21 on: September 26, 2019, 09:26:04 AM »

I costed the materials for a pair or bellows and it came out at about £60, including leather diamonds, corners, tape, covering etc. In the interests of wanting to learn how to do it (And notwithstanding Nick's warning) I plan to try it someday. Probably to replace some Lilliput bellows.
You can order them from Italy to be custom made. I think Theo offers this service (you need to ask him). When Igor was still making bellows I got some made about 3 yrs ago for a Lilliput for about €120!  The fold depth was a bit of an issue (Igor had two) but in the end it worked out without fouling the valves inside. I think now in 2019 it would cost at least double that. But then again, a Liliput with new bellows is a desirable thing  (:)
« Last Edit: September 26, 2019, 09:27:50 AM by RogerT »
Logged

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Cardboard for bellows
« Reply #22 on: September 26, 2019, 09:49:17 AM »

You’re right Malcolm. The best way to bend cardboard is with a straightedge and bone folder scoring parallel lines and not cutting into the material. BUT, you must get the grain direction right. It must run in line with the fold. All paper has a grain direction. This is much easier to demonstrate than to describe. Take for example a sheet of A4 paper, it has a long edge and a short edge. Bend the paper gently in one direction and then the other. It will curve much easier in one direction than the other. If it’s  easier on the short edge then that is long grain, and the other short grain. Imagine a piece of landscape corrugated cardboard. If the grooves  run top to bottom long grain , from side to side, short.
Confused? You will be. It’s vital to determine the grain for the folds.
  I’m pretty sure there’s something on YouTube , look for paper grain direction. I did one some years ago but it seems to have disappeared .
  Best of luck
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Cardboard for bellows
« Reply #23 on: September 27, 2019, 08:59:30 PM »

Wow..who’d a thunk it...paper grain.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Cardboard for bellows
« Reply #24 on: October 28, 2019, 10:55:27 PM »

When the bellows are made and the time comes to glue them to the frames it is advisable to pop a little weight on top to hold everything together until the glue goes off.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)
Pages: 1 [2]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal