Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Reed Plate Markings  (Read 2257 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Reed Plate Markings
« on: September 19, 2019, 10:47:08 PM »

I have a set of reads marked "O" what manfacturer does this suggest?

Is the deers head a trademark also? If so, whose?


Thanks....
« Last Edit: September 19, 2019, 11:08:03 PM by Peadar »
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Plate Markings
« Reply #1 on: September 19, 2019, 11:06:59 PM »

I believe they're Dix.
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reed Plate Markings
« Reply #2 on: September 19, 2019, 11:10:17 PM »

I believe they're Dix.
Thanks Edward, I thought they might be.

Any clue what Delta (i.e. a triangle) might be?
Logged

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reed Plate Markings
« Reply #3 on: September 19, 2019, 11:47:49 PM »

Logged

Graham Spencer

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3548
  • MAD as a wet Hohner........
Re: Reed Plate Markings
« Reply #4 on: September 20, 2019, 05:50:18 AM »

I believe they're Dix.
Thanks Edward, I thought they might be.

Any clue what Delta (i.e. a triangle) might be?

I have an unidentified but good quality well-built 3-voice box, probably just pre-WW2, which has its reeds numbered 1-10 and 1-11 from the chin end, and in each bank the number 5 is replaced by the triangle mark.  Having the number stamped into the reed plate makes it much easier to keep track of them when they're out of their blocks!  Incidentally I have a Koch with the mountain-goat (which is apparently what it is - thanks tirpous!) trademark reeds.

Graham
Logged
Among others, Saltarelle Pastourelle II D/G; Hohner 4-stop 1-rows in C & G; assorted Hohners; 3-voice German (?) G/C of uncertain parentage; lovely little Hlavacek 1-row Heligonka; Bâ™­/Eâ™­ Koch. Newly acquired G/C Hohner Viktoria. Also Fender Jazz bass, Telecaster, Stratocaster, Epiphone Sheraton, Charvel-Jackson 00-style acoustic guitar, Danelectro 12-string and other stuff..........

Squeezing in the Cyprus sunshine

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Plate Markings
« Reply #5 on: September 20, 2019, 09:22:17 AM »

"reeds numbered 1-10 and 1-11"

I seem to remember that the South American G/C Hering (21x8), which I had a while ago, had the treble reed plates numbered 1 to 21.

Edited to add....That's wrong, they were stamped all the way through to 42. Faulty memory!
« Last Edit: September 20, 2019, 05:53:15 PM by Winston Smith »
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reed Plate Markings
« Reply #6 on: September 20, 2019, 05:37:26 PM »

Here is another numbering scheme, with Roman numerals on the short edges.

(and no, the reeds are not from an Italian box !  ;D)
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Plate Markings
« Reply #7 on: September 23, 2019, 10:31:22 AM »

Surely those reedplates must start out as castings and are not just machined out of plate? I cannot imagine the numerals being machined, it would be very time consuming, even if possible. Which manufacturers instrument are they from?
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

tirpous

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1403
Re: Reed Plate Markings
« Reply #8 on: September 23, 2019, 03:53:54 PM »

The reeds are from a 2-row Globe Gold Medal (my avatar).  The plates are unusual: the sides of the slots are relieved, which must have complicated their fabrication too !
Logged

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reed Plate Markings
« Reply #9 on: September 23, 2019, 09:33:28 PM »

Surely those reedplates must start out as castings and are not just machined out of plate? I cannot imagine the numerals being machined, it would be very time consuming, even if possible. Which manufacturers instrument are they from?

The numbers wouldn't be machined they  would be stamped, with a hardened steel letter/number punch. Zinc and later Aluminium are soft metals and the reed plate blanks too would be stamped out of  plate /sheet. After stamping the plates might have been hand fettled but this is unlikely for mass produced boxes including hohners.
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Reed Plate Markings
« Reply #10 on: September 23, 2019, 11:07:48 PM »

I had a full set of letter/number punches, but they couldn't punch raised numbers or letters like these!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Reed Plate Markings
« Reply #11 on: September 23, 2019, 11:15:50 PM »

I had a full set of letter/number punches, but they couldn't punch raised numbers or letters like these!

Ooops. I stand corrected. The only possible process then is die casting.
Logged

Squeaky Pete

  • Squeaky Pete
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1327
  • Re-hohn a Hohner
Re: Reed Plate Markings
« Reply #12 on: September 23, 2019, 11:29:09 PM »

They look like they are die cast, but then the slot looks like it was cut after. Or maybe lengthened?
Maybe labour was very cheap in those days
Logged
Poker work DG.
Pariselle 2.6 DG, Ex-Club IIIBS CF,
Matching Liliputs in CF and DG,
Lots of sickly Hohners needing TLC,
Bassoon, Various Bagpipes........

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Reed Plate Markings
« Reply #13 on: September 24, 2019, 01:46:44 PM »

They look like they are die cast, but then the slot looks like it was cut after. Or maybe lengthened?
Maybe labour was very cheap in those days

Some reed plates are still made by casting, Italian bass reeds usually have cast plates.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

diatonix

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 622
Re: Reed Plate Markings
« Reply #14 on: September 24, 2019, 04:50:54 PM »

All that can be said is that reed plates marked with  "O" are from Eastern Germany (Saxony), usually associated with Weltmeister or one of its many predecessors. More often than not their quality is pretty basic.
Logged

Jesse Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 761
  • Buffalo, NY, USA
Re: Reed Plate Markings
« Reply #15 on: September 25, 2019, 02:58:48 AM »

Could the numerals be soldered or brazed on to the edge of the plate?
Logged
Hohner Pokerwork D/G (x2!), Hohner one row four stops in D and C, Hohner Presswood C/F.

Nick Collis Bird

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3785
  • Been squeezing melodeons for over 48 years (badly)
Re: Reed Plate Markings
« Reply #16 on: September 25, 2019, 05:51:29 AM »

Far too time consuming i would have thought. I’m pretty sure they’re cast.
Logged
Has anyone heard of the song. “ Broken Alarm-clock Blues” ? It starts   â€œI woke up this Afternoon”
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal