Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Organ Blower?  (Read 4716 times)

0 Members and 1 Guest are viewing this topic.

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Organ Blower?
« on: September 23, 2019, 03:09:06 PM »

I came across an advert for an "Organ Blower" which is basically a fan unit which I assume is used in a reed organ as it doesn't seem large enough for a pipe organ of any size. My immediate thought was a wind driven tuning table of course. The stated output is circa 3" water gauge of pressure, which meant nothing to me. A quick Google informed me that 28" water gauge is roughly 1 psi which is not a lot, so 3"wg is tiny! The fan unit looks quite big and is described as "heavy", the motor output is 0.25 h.p. so a little under 200 Watts.


Does anyone know anything about 'Organ Blowers' and how much air pressure is needed to sound a reed? Pictures attached, two more to follow in another post.
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

Pete Dunk

  • Typo Expert
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 3706
Re: Organ Blower?
« Reply #1 on: September 23, 2019, 03:11:41 PM »

More pics
Logged
Squeezing on the Isle of Oxney, UK
Primo (Serenellini) D/G
Isis D/G
Hohner B/E, G/C, C/F, Bb/Eb G/C/F
Liliputs D/G (G scale), C/F, Bb/Eb, Albrecht Custom D/G (G scale)

folkloristmark

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 582
    • street entertainers
Re: Organ Blower?
« Reply #2 on: September 23, 2019, 03:41:22 PM »

The only thing I know is small busker organs have a two part bellows joined by a simple leather valve, so like a bag pipe the pressure is built up from the blower source and held in a reserve to maintain constant flow to retain good pitch. The crude  tuning table blowers I have seen are direct adapted electric motors that were calibrated by using a voltage regulator to set the required simulated pressure.I think an organ blower or vac cleaner would work but the supply would need to be regulated with a voltage drop. Some motors require a load peak to actually start that may need to be taken into account. In my 12 volt reed organ the car battery needs to be very good to actually start the motor if the battery gets flat the problem is a restart even when the battery will power the organ for quite a time longer. So you might need two settings one to start the moter and another to maintain a correct pressure.Trail and error.
If this helps
« Last Edit: September 23, 2019, 03:49:58 PM by folkloristmark »
Logged
Mark Taylor
Folkloristmark

hickory-wind

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 627
  • Lives in NY USA near the Erie Canal
    • Bellingers' Button Boxes
Re: Organ Blower?
« Reply #3 on: September 23, 2019, 04:04:04 PM »

I use a blower driven air tuning table. I actually connected a manometer to a Hohner two row and played to determine the pressure:
http://bellingersbuttonboxes.com/workshop/

I now use a +/- 2" water column pressure gauge for most button accordion tuning and a +/- 5" water column for concertinas as they have a smaller bellows cross section and correspondingly higher pressure.

You can see my table in action here:
https://youtu.be/un-AvLaCenU

I use a laboratory DC power supply to finely adjust the pressure. The pressure gauge is in the video but washed out since the light setting was not optimal.

I have the blower in an adjacent closet surrounded with lots of sound deadening materials so my tuning room is very quiet.

Scott
Logged
too many boxes...please buy one, or two, or

Nigel

  • Respected Sage
  • ****
  • Offline Offline
  • Posts: 398
Re: Organ Blower?
« Reply #4 on: September 23, 2019, 04:42:35 PM »

Winston. I bet you would like one of these in your attic workshop  >:E
Logged

Winston Smith

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 4066
  • AKA Edward Jennings
    • "Our Luxor B&B" Luxor life, slice by slice.
Re: Organ Blower?
« Reply #5 on: September 23, 2019, 06:35:01 PM »

Funnily enough, Nige, I've recently bought a Farfisa Pianorgan 111 which is fan driven. I thought that if I couldn't get it to work, that's the very use I'd put the little fan motor to. However, it's OK and just needs a couple of reeds sorting and it'll be fine. Actually, I'm quite taken by it!
Logged
At last, broken and resigned to accept conformity.
Oh, how I LOVE Big Brother!

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Organ Blower?
« Reply #6 on: September 23, 2019, 09:26:18 PM »

I came across an advert for an "Organ Blower" which is basically a fan unit which I assume is used in a reed organ as it doesn't seem large enough for a pipe organ of any size. My immediate thought was a wind driven tuning table of course. The stated output is circa 3" water gauge of pressure, which meant nothing to me. A quick Google informed me that 28" water gauge is roughly 1 psi which is not a lot, so 3"wg is tiny! The fan unit looks quite big and is described as "heavy", the motor output is 0.25 h.p. so a little under 200 Watts.


Does anyone know anything about 'Organ Blowers' and how much air pressure is needed to sound a reed? Pictures attached, two more to follow in another post.

I think we all tend to over estimate the pressure that melodeon reeds run on. Internal dimensions of a Hohner 2915/1040/3515 bellows are roughly 10 inch high by 6 inch wide. So that's 60 square inches. I'm damn sure I am not doing a 60lb push in (or draw out) . 6lbs may be - do that for an hour and my chest muscles ache the next morning. 6lbs on 60 square inches....That wouldn't be far away from the 3inch water gauge . Scott's 2inch (50mm) gauge pressure strikes me as pretty bang on mark.

Logged

John MacKenzie (Cugiok)

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2360
  • Fettling... Learning to reed and right.
Re: Organ Blower?
« Reply #7 on: September 24, 2019, 05:52:08 PM »

Do I misremember or has Owen Wood not got something to do with organ building in real life?

SJ
Logged
There is no beginning to my talent :)



: Hohner Club Modell 1. Bb/Eb, de-clubbed : Early Hohner Pressed Wood A/D : 1930's Varnished wood G/C:  Hohner Erika C/F: Bandoneon tuned D/G Pressed wood: Koch F/Bb; G/C Pre Corso

Mike Hirst

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1433
  • Black Dot B/C, Bastardo C#/D, Corona II GCF
Re: Organ Blower?
« Reply #8 on: September 24, 2019, 09:35:44 PM »

I have an uncle who owns on of these, which was previously used to run  a small (two manual) church organ in his 300 year old cottage in Derbyshire. The other main feature of which is a bar with optics. Hymns and whisky were the order of the day. The organ no longer functions, but B.O.B. (British Organ Blowers) are still active. Full details can be found on their website:

http://www.bobstevenson.com

This is an old school family run business, with a good reputation. I am sure that they would give good advice if contacted:

e-mail: sales@bobstevenson.co.uk
or stephen@bobstevenson.co.uk

Tel: +44 (0) 1332 574112
Fax: +44 (0) 1332 757286

B.O.B.Stevenson Ltd
Coleman Street
Derby
DE24 8NL
UK
Logged
Semper idem, sed non eodem modo
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal