Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Case work - broken glue joint repair (and another "old box" problem)  (Read 1009 times)

0 Members and 1 Guest are viewing this topic.

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039

The latest aquisition ( C/C# 19 key "German pattern" International - late 1890's/early 1900s) suffered a mishap as I tried to get the inevitable jammed stop  freed off.
I had opened the box up to get at the stop crosshead/slide arrangement and managed to pull the bottom edge of the casework frame off the fondo. The fondo is a flat board approx 3mm thick and fits into a rebate in the cframe inside edge.
Fortunately the break is entirely in the glue.

Question now is to make sure I use an appropriate technique to clean back the seperated parts  and an appropriate glue.

I suspect pearl glue is the way to go. I can't imagine that there would be any major interaction problems between this and any similar hide based glue that might have been used in Saxony at the time when Vicky R was Europe's international granny.

Surface preparation I am not so sure about.

Also - looking at the glue run round the inside of the fondo seam this is largely crazed. I suspect brushing a fresh layer of hot glue over those seams will help the overall airtightness of the box.

2) The gasket is still the original black candlewick. Can anyone recommend a supplier of - preferably black- candlewick though I could always dye some white candlewick if I had to. The Germans were world leaders in industrial chemistry in the late 19th century so it is very likely that the Black candlewick used in original manufacture would have been dyed with a synthetic dye anyway.

3) Inevitably one treble key sticks (the sticky bass key was sorted with a tiny drop of clock oil on the trunnion cheeks) keyboard is a semi enclosed type which appears to be same construction as modern hand built 1rows. It seats back after a very light touch but jams open if you go any further.
If anyone has experience of this particular problem and possible solutions information gratefully received.

4. Finally - and just as a matter of passing interest, it has steel reeds on zinc plates ("O" mark). Which seem fine- though not as strong sounding as the brass reeds in my AD. A bit of a rattle off the valves - but my experience over the last 9 months is that if you tolerate a tired leather valve which doesn't seat properly for a few hours playing most of them actually recover their flexibility, just like old dried out leather boots can be brought back to life by hard labour and dubbin.

Must go. The day job calls!

Peadar


Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Case work - broken glue joint repair (and another "old box" problem)
« Reply #1 on: October 04, 2019, 09:20:54 AM »

Point 1 - glue.  Almost certainly the original glue is a protein type eg pearl glue, hide glue etc.  So use something similar for the rebuild. But remove all the old glue first or you won’t get a tight joint.  The old glue can be softened with moist heat,  eg steam, or a hot wet cloth.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Peadar

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2039
Re: Case work - broken glue joint repair (and another "old box" problem)
« Reply #2 on: October 06, 2019, 05:12:15 PM »

Point 1 : Thanks Theo. Hide glue now on order.

Point 2: White candlewick is available by the spool.... I have ordered however some black cotton crotchet yarn. If that doesn't have enough body I will obtain candlewick.

Point 3: this may be helped by a dry household atmosphere.... which will depend on me getting a new CH boiler as the old one has recently died. After that I guess it's PTFE sprinkles...and or take the keyboard off to get a better look

Logged

pete /acorn

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 930
  • .Cast Trilly
    • Acorn Instruments
Re: Case work - broken glue joint repair (and another "old box" problem)
« Reply #3 on: October 08, 2019, 09:12:49 AM »

Somethin I would do,When you have re glued the joint I would fit a 10 or 15mm quadrant round the inside if the box on the pallet side.
If this is glued into place it will form a good seal and strengthen the joint between the fondo and the case.
Logged
Acorn Instruments are specialist retailers of Castagnari Instruments,and have an extensive stock of new instruments on the shelf for prompt delivery in standard layouts however these can easily be changed to customers special requirements,we have over 600 reeds in stock
 We also have the largest stock in the UK of  pre loved melodons all fully serviced,and with 12 months warranty
UK and international customers catered for
www.acorninstruments.co.uk
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal