Melodeon.net Forums

Please login or register.

Login with username, password and session length
Advanced search  

News:

Welcome to the new melodeon.net forum

Pages: [1]   Go Down

Author Topic: Hohner valve noise  (Read 1509 times)

0 Members and 1 Guest are viewing this topic.

John Stoutimore

  • Member
  • *
  • Offline Offline
  • Posts: 16
Hohner valve noise
« on: November 14, 2019, 12:30:17 PM »

I have three Hohner 3-rows, a $500 Panther, an $800 Compadre, and a $1600 Corona II Classic. The Panther and the Corona make what I believe is called "valve noise" on the low bass notes when playing hard. It's a rattling-rumbling sound. Somewhere I think I read that the Compadre has a feature to suppress valve noise. In any case, the Compadre never make this noise. What design feature would accomplish this? And if there is such a design feature, why would Hohner add it to a relatively low-budget model but not on more costly models?
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner valve noise
« Reply #1 on: November 14, 2019, 01:01:49 PM »

In my experience, there are two types of valve noise:

1. A transient rasp-like rattle which occurs when changing bellows direction whilst holding down a button. This is usually associated with plastic/vinyl valves on the lower notes (= larger reeds). The rattle can be much reduced by fitting leather valves, especially if you incorporate a booster spring on the larger valves.

2. A low rumbling noise which develops as a low bass note is played and sustained, especially under higher bellows pressure. Often the low rumble is perceived to be an octave lower than the main note itself. The cause is usually due to the reed tongue (often one with a brass weight) contacting the valve on the opposite side of the reed plate slot. The contact only occurs once the swing amplitude of the reed tongue becomes large enough to hit the valve. I guess this is the type of valve noise you are experiencing. A possible remedy is to install a valve which opens further, either by reducing the glued length of the valve at the hinge/rivet end, or else reducing the strength of any booster spring. (or play less vigorously!)
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner valve noise
« Reply #2 on: November 14, 2019, 02:10:12 PM »

To answer the specific question: the design feature that avoids valve noise is to use good quality leather or leather/plastic composite valves.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Hohner valve noise
« Reply #3 on: November 14, 2019, 02:43:54 PM »

2. A low rumbling noise which develops as a low bass note is played and sustained, especially under higher bellows pressure. Often the low rumble is perceived to be an octave lower than the main note itself. The cause is usually due to the reed tongue (often one with a brass weight) contacting the valve on the opposite side of the reed plate slot.

Huh, I think this may be a physical example of the under tone series/negative harmonic series. That's pretty cool!
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner valve noise
« Reply #4 on: November 14, 2019, 03:09:23 PM »

2. A low rumbling noise which develops as a low bass note is played and sustained, especially under higher bellows pressure. Often the low rumble is perceived to be an octave lower than the main note itself. The cause is usually due to the reed tongue (often one with a brass weight) contacting the valve on the opposite side of the reed plate slot.

Huh, I think this may be a physical example of the under tone series/negative harmonic series. That's pretty cool!
Nope! It's the valve contact. Remove the valve and the noise goes away!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

Rog

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 2525
  • Repair and tuning in Hants
Re: Hohner valve noise
« Reply #5 on: November 14, 2019, 03:29:40 PM »

If you can identify specific notes that rattle, I would try replacing the valve. Often this does solve the issue. If you can get the reed block out and onto a tuning table, you may be able to diagnose the problem by observing it working (on an outside/push bellows Reed). Valves make unwanted noises for all sorts of reasons. Replacing noisy valves saves the bother of trying to work out why/how a valve is misbehaving, and it can be a quick solution. Though if they are *all* making a noise then that’s a bigger job.

Gena Crisman

  • Hero Member
  • *****
  • Offline Offline
  • Posts: 1108
  • 🇬🇧
Re: Hohner valve noise
« Reply #6 on: November 14, 2019, 03:43:15 PM »

Apologies for the off topic nature, but, yes, I do mean specifically because of the two components acting together to form said impacts. I believe it would mimic tuning forks making incomplete contact with surfaces, and making lower frequency sounding buzzes, which was recently a popular way to demonstrate/produce the undertone series.

Said buzzing doesn't sound particularly good, I imagine, but perhaps an interesting relationship exists there.
Logged

Steve_freereeder

  • Content Manager
  • Hero Member
  • ***
  • Offline Offline
  • Posts: 7511
  • MAD is inevitable. Keep Calm and Carry On
    • Lizzie Dripping
Re: Hohner valve noise
« Reply #7 on: November 14, 2019, 03:53:50 PM »

Apologies for the off topic nature, but, yes, I do mean specifically because of the two components acting together to form said impacts. I believe it would mimic tuning forks making incomplete contact with surfaces, and making lower frequency sounding buzzes, which was recently a popular way to demonstrate/produce the undertone series.
Ah - I agree. I misunderstood your previous post, sorry!
The low-frequency vibration is indeed exactly like your tuning fork analogy!
Logged
Steve
Sheffield, UK.
www.lizziedripping.org.uk

John Stoutimore

  • Member
  • *
  • Offline Offline
  • Posts: 16
Re: Hohner valve noise
« Reply #8 on: November 14, 2019, 06:29:32 PM »

A possible remedy is to install a valve which opens further, either by reducing the glued length of the valve at the hinge/rivet end, or else reducing the strength of any booster spring.
[/quote]

So essentially, I would be looking for valves that are more flexible, not more rigid? Some opine that leather reeds are superior to plastic. But would that necessarily be the case if I'm looking for more flexible valves?
Logged

Theo

  • Administrator
  • Hero Member
  • *****
  • Offline Offline
  • Posts: 14475
  • Hohner Club Too
    • The Box Place
Re: Hohner valve noise
« Reply #9 on: November 14, 2019, 07:00:45 PM »

If the valves have more than one layer you can increase the opening by shortening, or removing the top layer.  Try removing a quarter of the length at a time.   Remove the whole top layer if necessary.
Logged
Theo Gibb - Gateshead UK

Proprietor of The Box Place for melodeon and concertina sales and service.
See my YouTube channel  for videos on repair and tuning
Pages: [1]   Go Up
 


Melodeon.net - (c) Theo Gibb; Clive Williams 2010. The access and use of this website and forum featuring these terms and conditions constitutes your acceptance of these terms and conditions.
SimplePortal 2.3.5 © 2008-2012, SimplePortal